component
NCP600SNADJT1G
Public Made by Adomby adom
onsemi Linear Voltage Regulators (LDO), TSOP-5. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownNCP600SNADJT1G
onsemi · Linear Voltage Regulators (LDO) · TSOP-5
NCP600SNADJT1G from onsemi, in a TSOP-5. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | Vin | power_in | Positive power supply input; the operating input voltage range is 1.75 V to 6 V, and Vin must be at least Vout + VDO. |
| 2 | GND | power_in | Power supply ground, also connected to the device substrate. |
| 3 | ENABLE | input | Enable input places the device into low-power standby when pulled below 0.4 V logic low; connect to Vin if the function is not used. |
| 4 | ADJ/NC | input | Output voltage adjust input for the adjustable version (ADJ), where the output is set by external resistors from 5.0 V down to 1.25 V and input bias current IADJ is typically less than 150 nA; no connection on fixed voltage versions. |
| 5 | Vout | output | Regulated output voltage, delivering up to 150 mA of output current. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | onsemi |
| Package | TSOP-5 |
| Category | Power Management ICs |
| Pins | 5 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Output Voltage | Vout | 1.231 | 1.25 | 1.269 | V | Iout = 1.0 mA to 150 mA; Vin = 1.75 V to 6.0 V; Vout = ADJ | 3 |
| Output Short Circuit Current | Isc | 300 | 550 | 800 | mA | Vout = 0 V | 3 |
| Dropout Voltage (1.25 V) | VDO | 175 | 250 | mV | Measured at: Vout, 2.0%, Iout = 150 mA | 3 | |
| Load Regulation | Regload | 2 | 15 | mV | Iout = 1.0 mA to 150 mA | 3 | |
| Line Regulation | Regline | 1 | 10 | mV | Vin = 1.750 V to 6.0 V, Iout = 1.0 mA | 3 | |
| Disable Current | IDIS | 0.01 | 1 | A | ENABLE = 0 V, Vin = 6 V; TA = −40°C to 85°C | 4 | |
| Ground Current (1.25 V Adjustable) | IGND | 100 | 135 | A | ENABLE = 0.9 V, Iout = 1.0 mA to 150 mA | 4 | |
| ADJ Input Bias Current | IADJ | -0.75 | 0.75 | A | 4 | ||
| ENABLE Input Threshold Voltage, Logic High | Vth(EN) | 0.9 | V | Voltage Increasing, Logic High | 4 | ||
| ENABLE Input Threshold Voltage, Logic Low | Vth(EN) | 0.4 | V | Voltage Decreasing, Logic Low | 4 | ||
| Enable Input Bias Current | IEN | 3 | 100 | nA | 4 | ||
| Output Turn On Time (1.25 V) | tEN | 15 | 25 | s | ENABLE = 0 V to Vin | 4 | |
| Operating Input Voltage | Vin | 1.75 | 6 | V | 2 | ||
| Adjustable Output Voltage | Vout | 1.25 | 5 | V | Adjustable Version Only | 2 | |
| Output Current | Iout | 0 | 150 | mA | 2 | ||
| Ambient Temperature | TA | -40 | 125 | °C | 2 | ||
| Input Voltage Range | Vin | -0.3 | 6.5 | V | 2 | ||
| Output, Enable, Adjustable Voltage Range | Vout, ENABLE, ADJ | -0.3 | 6.5 | V | or Vin + 0.3, whichever is lower | 2 | |
| Maximum Junction Temperature | TJ(max) | 150 | °C | 2 | |||
| Storage Temperature Range | TSTG | -65 | 150 | °C | 2 | ||
| ESD Capability, Human Body Model | ESDHBM | 3500 | V | Tested per AEC−Q100−002 (EIA/JESD22−A114) | 2 | ||
| ESD Capability, Machine Model | ESDMM | 200 | V | Tested per AEC−Q100−003 (EIA/JESD22−A115) | 2 | ||
| Power Supply Ripple Rejection at 120 Hz | PSRR | 62 | dB | Iout = 1.0 mA to 150 mA, f = 120 Hz | 3 | ||
| Power Supply Ripple Rejection at 1.0 kHz | PSRR | 55 | dB | Iout = 1.0 mA to 150 mA, f = 1.0 kHz | 3 | ||
| Power Supply Ripple Rejection at 10 kHz | PSRR | 38 | dB | Iout = 1.0 mA to 150 mA, f = 10 kHz | 3 | ||
| Output Noise Voltage | Vn | 50 | Vrms | f = 10 Hz to 100 kHz | 3 | ||
| Thermal Shutdown Temperature | TSD | 175 | °C | 4 | |||
| Thermal Shutdown Hysteresis | TSH | 10 | °C | 4 | |||
| Thermal Resistance, Junction-to-Air (TSOP-5) | RJA | 215 | °C/W | Values based on copper area of 645 mm2, 1 oz copper thickness | 2 |
CAD (KiCad official)
- Symbol:
NCP600SNADJT1G - Footprint:
Package_SO:TSOP-5_1.65x3.05mm_P0.95mm - 3D model: TSOP-5 (KiCad packages3D, STEP)
- 3D model files:
ncp600snadjt1g-etched.step/ncp600snadjt1g-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ncp600snadjt1g.step/ncp600snadjt1g.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: onsemi datasheet (15 pp, sha256
ea92c12502a32ad7, retrieved 2026-11-02, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).