← Commit history

Initial commit: component/ncp59744mn2adjtbg

Ray ·aead891a20 ·
2 files changed +95
README.mdadded+61
@@ -0,0 +1,61 @@+# NCP59744MN2ADJTBG++**onsemi** · Voltage Regulators - Linear, Low Drop Out (LDO) Regulators · QFN-20(5x5)++NCP59744MN2ADJTBG from onsemi, in a QFN-20(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | OUT | power_out | Regulated output voltage (0.8 V to 3.6 V). One of four paralleled OUT pins (1, 18, 19, 20). Recommended COUT >= 2.2 uF ceramic. |+| 2 | NC | unconnected | No connection. May be left floating or tied to GND for improved thermal contact to the top-side plane. |+| 3 | NC | unconnected | No connection. May be left floating or tied to GND for improved thermal contact to the top-side plane. |+| 4 | NC | unconnected | No connection. May be left floating or tied to GND for improved thermal contact to the top-side plane. |+| 5 | IN | power_in | Unregulated input to the pass device (VIN 0.8 V to 5.5 V). One of four paralleled IN pins (5, 6, 7, 8). |+| 6 | IN | power_in | Unregulated input to the pass device (VIN 0.8 V to 5.5 V). One of four paralleled IN pins (5, 6, 7, 8). |+| 7 | IN | power_in | Unregulated input to the pass device (VIN 0.8 V to 5.5 V). One of four paralleled IN pins (5, 6, 7, 8). |+| 8 | IN | power_in | Unregulated input to the pass device (VIN 0.8 V to 5.5 V). One of four paralleled IN pins (5, 6, 7, 8). |+| 9 | PG | output | Power-Good open-drain, active-high output. Goes high-Z when VOUT exceeds the PG trip threshold (~90% of nominal) and is pulled low otherwise. Requires an external 10 kOhm to 1 MOhm pull-up to a supply up to 5.5 V. May be left floating if unused. |+| 10 | BIAS | power_in | Bias input voltage (2.2 V to 5.5 V) for the error amplifier, reference, and internal control circuits. Typical IBIAS ~1.3 mA. |+| 11 | EN | input | Enable pin. Driving high (>=1.1 V) enables the regulator; driving low (<=0.4 V) puts it into shutdown. Must not be left floating. 100 mV hysteresis and ~20 us deglitch. |+| 12 | GND | power_in | Ground reference for the regulator. |+| 13 | NC | unconnected | No connection. May be left floating or tied to GND for improved thermal contact to the top-side plane. |+| 14 | NC | unconnected | No connection. May be left floating or tied to GND for improved thermal contact to the top-side plane. |+| 15 | SS | passive | Soft-Start pin. A capacitor from this pin to GND sets the startup time using ISS ~0.45 uA charging. If left floating, soft-start ramp is typically 200 us. Must not be left floating for user-programmed soft-start. |+| 16 | FB | input | Feedback input to the error amplifier. Connect to the center tap of an external resistor divider that sets the output voltage (VREF = 0.8 V). Must not be left floating. |+| 17 | NC | unconnected | No connection. May be left floating or tied to GND for improved thermal contact to the top-side plane. |+| 18 | OUT | power_out | Regulated output voltage. One of four paralleled OUT pins (1, 18, 19, 20). |+| 19 | OUT | power_out | Regulated output voltage. One of four paralleled OUT pins (1, 18, 19, 20). |+| 20 | OUT | power_out | Regulated output voltage. One of four paralleled OUT pins (1, 18, 19, 20). |+| PAD | GND | power_in | Exposed thermal pad on the underside of the package. Must be soldered to the PCB ground plane for proper thermal performance and electrical grounding. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | onsemi |+| Package | QFN-20(5x5) |+| Category | PMIC |+| Pins | 21 |++## Ordering variants++- `NCP59744MN2ADJTBG`+- `NCP59744MN2ADJTBGNCP59744MN1ADJTBG`++## CAD (KiCad official)++- Symbol: `NCP59744MN2ADJTBG`+- Footprint: `Package_DFN_QFN:QFN-20-1EP_5x5mm_P0.65mm_EP3.35x3.35mm`+- 3D model: QFN-20(5x5) (KiCad packages3D, STEP)++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [onsemi datasheet](docs/ncp59744mn2adjtbg-datasheet.pdf) (12 pp, sha256 `85f37db2e0c8407b`, retrieved 2026-08-17, tier: lcsc)+- **Extractor:** `ds2sf` (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/ncp59744mn2adjtbg-datasheet.pdf)
page.jsonadded+34
@@ -0,0 +1,34 @@+{+  "slug": "ncp59744mn2adjtbg",+  "version": "0.1.0",+  "type": "component",+  "description": "onsemi Voltage Regulators - Linear, Low Drop Out (LDO) Regulators, QFN-20(5x5). Datasheet-verified pinout, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "pmic",+    "ncp59744mn2adjtbg"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "ncp59744mn2adjtbg.kicad_sym",+    "ncp59744mn2adjtbg.kicad_mod",+    "ncp59744mn2adjtbg.glb",+    "ncp59744mn2adjtbg.step",+    "ncp59744mn2adjtbg.lbr",+    "docs/hero.png",+    "docs/ncp59744mn2adjtbg-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "visibility": "public",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file