Generated by kicad-footprint-generator · KiCad file format 20260206
NCP51561DADWR2G
onsemi · Gate Drivers · SOIC-16-300mil
NCP51561DADWR2G from onsemi, in a SOIC-16-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | INA | input | Logic input for Channel A with an internal pull-down resistor to GND. |
| 2 | INB | input | Logic input for Channel B with an internal pull-down resistor to GND. |
| 3 | VDD | power_in | Input-side supply voltage; a bypass capacitor from VDD to GND is recommended. |
| 4 | GND | power_in | Input-side power ground; all input-side signals are referenced to this pin. |
| 5 | ENA/DIS | input | Enable/disable logic input: logic high enables both outputs with an internal pull-up in the ENABLE version, and logic high disables both outputs with an internal pull-down in the DISABLE version. |
| 6 | DT | input | Programmable dead-time input: floating gives Mode-A with dead time below a maximum of 20 ns and no cross-conduction, RDT sets tDT (ns) = 10 x RDT (kΩ) with RDT between 1 kΩ and 300 kΩ, and pulling DT to VDD gives Mode-C where cross-conduction is allowed. |
| 7 | ANB | input | Input configuration select with an internal pull-down to GND; when high, OUTA and OUTB are complementary outputs from the INA PWM input regardless of INB, and it is recommended to tie it to GND if unused. |
| 8 | VDD | power_in | Input-side supply voltage; a bypass capacitor from VDD to GND is recommended. |
| 9 | VSSB | power_in | Power ground for Channel B. |
| 10 | OUTB | output | Gate drive output for Channel B. |
| 11 | VCCB | power_in | Power supply for output Channel B; a bypass capacitor from VCCB to VSSB is recommended. |
| 12 | NC | unconnected | No connection; keep pin floating. |
| 13 | NC | unconnected | No connection; keep pin floating. |
| 14 | VSSA | power_in | Power ground for Channel A. |
| 15 | OUTA | output | Gate drive output for Channel A. |
| 16 | VCCA | power_in | Power supply for output Channel A; a bypass capacitor from VCCA to VSSA is recommended. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | onsemi |
| Package | SOIC-16-300mil |
| Category | Motor Driver ICs |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VDD Quiescent Current | IQVDD | 500 | 780 | 1000 | µA | VINA= VINB = 0 V, VENABLE = VDD or VDISABLE = 0 V | 9 |
| VDD Quiescent Current | IQVDD | 500 | 820 | 1000 | µA | VINA= VINB = 5 V, VENABLE = 0 V or VDISABLE = VDD | 9 |
| VDD Quiescent Current | IQVDD | 7 | 12 | 16 | mA | VINA = VINB = 5 V, VENABLE = VDD or VDISABLE = 0 V | 9 |
| VDD Operating Current | IVDD | 5 | 7.15 | 9 | mA | fIN = 500 kHz, 50% duty cycle, COUT = 100 pF | 9 |
| VDD Supply Under-Voltage Positive-Going Threshold | VDDUV+ | 2.7 | 2.8 | 2.9 | V | VDD = Sweep | 9 |
| VDD Supply Under-Voltage Negative-Going Threshold | VDDUV- | 2.6 | 2.7 | 2.8 | V | VDD = Sweep | 9 |
| VCCA and VCCB Quiescent Current | IQVCCA | 200 | 280 | 500 | µA | VINA = VINB = 0 V, per channel | 9 |
| VCCA and VCCB Quiescent Current | IQVCCB | 300 | 410 | 600 | µA | VINA = VINB = 5 V, per channel | 9 |
| VCCA and VCCB Operating Current | IVCCA | 2 | 3 | 5.5 | mA | Current per channel (fIN = 500 kHz, 50% duty cycle), COUT = 100 pF | 9 |
| VCCA and VCCB Supply Under-Voltage Positive-Going Threshold (17-V UVLO) | VCCAUV+ | 16 | 17 | 18 | V | 9 | |
| VCCA and VCCB Supply Under-Voltage Negative-Going Threshold (17-V UVLO) | VCCAUV- | 15 | 16 | 17 | V | 9 | |
| Under-Voltage Debounce Time (17-V UVLO) | tUVFLT | 10 | s | Note 19 | 9 | ||
| High Level Input Voltage | VINH | 1.4 | 1.6 | 1.8 | V | 9 | |
| Low Level Input Voltage | VINL | 0.9 | 1.1 | 1.3 | V | 9 | |
| High Level Logic Input Bias Current | IIN+ | 20 | 25 | 33 | µA | VIN = 5 V | 10 |
| Low Level Logic Input Bias Current | IIN- | 1 | µA | VIN = 0 V | 10 | ||
| Enable High Voltage | VENAH | 1.4 | 1.6 | 1.8 | V | ENABLE version only | 10 |
| Enable Low Voltage | VENAL | 0.9 | 1.1 | 1.3 | V | ENABLE version only | 10 |
| Minimum Dead-Time | tDT,MIN | 0 | 10 | 29 | ns | DT pin is left open | 10 |
| Dead-Time | tDT | 145 | 200 | 255 | ns | RDT = 20 k | 10 |
| Dead-Time | tDT | 800 | 1000 | 1200 | ns | RDT = 100 k | 10 |
| Dead-Time Mismatch between OUTB to OUTA and OUTA to OUTB | tDT | -30 | 30 | ns | RDT = 20 k | 10 | |
| Dead-Time Mismatch between OUTB to OUTA and OUTA to OUTB | tDT | -150 | 150 | ns | RDT = 100 k | 10 | |
| DT Threshold Voltage for OUTA and OUTB Overlap | VDT,SHORT | 0.85 | 0.9 | 0.95 | xVDD | DT pin Pulled to VDD | 10 |
| OUTA and OUTB Source Peak Current | IOUTA+ | 2.6 | 4.5 | A | VINA = VINB = 5 V, PW ≤ 5 s, VCCA = VCCB = 12 V | 10 | |
| OUTA and OUTB Sink Peak Current | IOUTA- | 7 | 9 | A | VINA = VINB = 5 V, PW ≤ 5 s, VCCA = VCCB = 12 V | 10 | |
| Output Resistance at High State | ROH | 1.4 | 2.7 | IOUTH = 100 mA | 10 | ||
| Output Resistance at Low State | ROL | 0.5 | 1 | IOUTL = 100 mA | 10 | ||
| High Level Output Voltage (VCC - VOUT) | VOHA, VOHB | 270 | mV | IOUT = 100 mA | 10 | ||
| Low Level Output Voltage (VOUT - VSS) | VOLA, VOLB | 100 | mV | IOUT = 100 mA | 10 | ||
| Turn-On Propagation Delay from INx to OUTx | tPDON | 22 | 36 | 55 | ns | VCCA = VCCB = 12 V, CLOAD = 0 nF | 10 |
| Turn-On Propagation Delay from INx to OUTx | tPDON | 25 | 39 | 58 | ns | VCCA = VCCB = 20 V, CLOAD = 0 nF | 10 |
| Turn-Off Propagation Delay from INx to OUTx | tPDOFF | 22 | 36 | 55 | ns | VCCA = VCCB = 12 V, CLOAD = 0 nF | 10 |
| Turn-Off Propagation Delay from INx to OUTx | tPDOFF | 25 | 39 | 58 | ns | VCCA = VCCB = 20 V, CLOAD = 0 nF | 10 |
| Pulse Width Distortion (tPDON - tPDOFF) | tPWD | -5 | 5 | ns | 10 | ||
| Turn-On Rise Time | tR | 9 | 16 | ns | VCCA = VCCB = 12 V, CLOAD = 1.8 nF | 10 | |
| Turn-On Rise Time | tR | 11 | 19 | ns | VCCA = VCCB = 20 V, CLOAD = 1.8 nF | 10 | |
| Turn-Off Fall Time | tF | 8 | 16 | ns | VCCA = VCCB = 12 V, CLOAD = 1.8 nF | 10 | |
| Turn-Off Fall Time | tF | 10 | 19 | ns | VCCA = VCCB = 20 V, CLOAD = 1.8 nF | 10 | |
| ENABLE to OUTx Turn-On Propagation Delay | TENABLE,OUT | 22 | 36 | 55 | ns | VCCA = VCCB = 12 V | 10 |
| ENABLE to OUTx Turn-On Propagation Delay | TENABLE,OUT | 25 | 39 | 58 | ns | VCCA = VCCB = 20 V | 10 |
| Glitch Filter on the ANB Pin | TFLT,ANB | 2 | 3.3 | 4.5 | s | 11 | |
| Common Mode Transient Immunity | CMTI | 200 | V/ns | Slew rate of GND versus VSSA and VSSB. INA and INB both are tied to VDD or GND. VCM = 1500 V | 11 | ||
| VDD to GND Power Supply Voltage - Input Side | VDD | -0.3 | 5.5 | V | 7 | ||
| VCCA-VSSA, VCCB-VSSB Power Supply Voltage - Driver Side | VCCA | -0.3 | 33 | V | 7 | ||
| INA, INB, and ANB Input Signal Voltages | VIN | -0.3 | 20 | V | 7 | ||
| ENA/DIS Input Signal Voltages | VENA/DIS | -0.3 | 5.5 | V | 7 | ||
| Junction Temperature | TJ | -40 | 150 | °C | 7 | ||
| Storage Temperature | TS | -65 | 150 | °C | 7 | ||
| Power Supply Voltage - Input Side | VDD | 3 | 5 | V | 8 | ||
| Power Supply Voltage - Driver Side (17-V UVLO Version) | VCCA, VCCB | 18.5 | 30 | V | 17-V UVLO Version | 8 | |
| Logic Input Voltage at Pins INA, INB, and ANB | VIN | 0 | 18 | V | 8 | ||
| Logic Input Voltage at Pin ENA/DIS | VENA/DIS | 0 | 5 | V | 8 | ||
| Ambient Temperature | TA | -40 | 125 | C | 8 | ||
| Junction Temperature | TJ | -40 | 125 | C | 8 | ||
| Supply Under-Voltage Lockout Hysteresis (17-V UVLO) | VCCHYS | 1 | V | 9 | |||
| Thermal Resistance Junction-Air 16-SOIC-WB, 100 mm2 1 oz Copper 1S0P | RJA | 120 | °C/W | 100 mm2, 1 oz Copper, 1 Surface Layer (1S0P) | 8 | ||
| Thermal Resistance Junction-Air 16-SOIC-WB, 100 mm2 2 oz Copper 1S0P | RJA | 81 | °C/W | 100 mm2, 2 oz Copper, 1 Surface Layer (1S0P) | 8 | ||
| Thermal Resistance Junction-Case | RJC | 38 | °C/W | 100 mm2, 1 oz Copper, 1 Surface Layer (1S0P) | 8 |
CAD (KiCad official)
- Symbol:
NCP51561DADWR2G - Footprint:
Package_SO:SOIC-16W_7.5x10.3mm_P1.27mm - 3D model: SOIC-16-300mil (KiCad packages3D, STEP)
- 3D model files:
ncp51561dadwr2g-etched.step/ncp51561dadwr2g-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ncp51561dadwr2g.step/ncp51561dadwr2g.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: onsemi datasheet (33 pp, sha256
deb63419d48eaf1b, retrieved 2026-11-20) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).