main
Ray Publish 0.1.0 cd62d6c

NCP4318ALKDR2G

onsemi · Monitors & Reset Circuits · SOIC-8

NCP4318ALKDR2G from onsemi, in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 GATE1 output Gate drive output for SR MOSFET1; the gate output pin voltage is rated −0.3 to 17 V with respect to GND.
2 GND power_in Ground reference for the device; all pin voltage ratings are specified with respect to this GND pin.
3 VS1 input Synchronous rectifier source sense input for SR1; the source sense pin is rated −0.3 to 5.5 V (−4 to 5.5 V dynamic for 200 ns pulses) with a recommended range of −0.3 to 5 V.
4 VD1 input Synchronous rectifier drain sense input; the IOFFSET1 current source flows out of this pin so an external series resistor sets the SR turn-off threshold, and the current is off when VDD is under-voltage or switching is disabled in green mode; the drain sense pin is rated −4 to 200 V.
5 VS2 input Synchronous rectifier source sense input for SR2; the source sense pin is rated −0.3 to 5.5 V (−4 to 5.5 V dynamic for 200 ns pulses) with a recommended range of −0.3 to 5 V.
6 VD2 input Synchronous rectifier drain sense input; the IOFFSET2 current source flows out of this pin so an external series resistor sets the SR turn-off threshold, and the current is off when VDD is under-voltage or switching is disabled in green mode; the drain sense pin is rated −4 to 200 V.
7 VDD power_in Supply voltage input; the recommended VDD range is 0 to 35 V to GND, with an absolute maximum rating of −0.3 to 37 V.
8 GATE2 output Gate drive output for SR MOSFET2; the gate output pin voltage is rated −0.3 to 17 V with respect to GND.

Key specifications

Parameter Value
Manufacturer onsemi
Package SOIC-8
Category Power Supply Chip
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Power Supply Input Pin Voltage VDD -0.3 37 V 4
Drain Sense Input Pin Voltage VD1, VD2 -4 200 V 4
Gate Drive Output Pin Voltage VGATE1, VGATE2 -0.3 17 V 4
Source Sense Input Pin Voltage VS1, VS2 -0.3 5.5 V 4
Source Sense Input Pin Dynamic Voltage VS1-DYN, VS2-DYN -4 5.5 V Pulse Width = 200 ns 4
Power Dissipation PD 0.625 W TA = 25°C, SOIC-8 4
Maximum Junction Temperature TJ -40 150 °C 4
Storage Temperature Range TSTG -60 150 °C 4
Lead Temperature TL 260 °C Soldering, 10 seconds 4
Electrostatic Discharge Capability, Human Body Model 3 kV ANSI/ESDA/JEDEC JS-001-2012 (except VD1, VD2 pins) 4
Electrostatic Discharge Capability, Human Body Model VD1-GND, VD2-GND 2 kV VD1-GND, VD2-GND pin to pin with 330 pF capacitance on VD1 and VD2 pin 4
Electrostatic Discharge Capability, Charged Device Model 1 kV JESD22-C101 4
VDD Pin Supply Voltage to GND VDD 0 35 V 4
Drain Sense Input Pin Voltage VD1, VD2 -0.7 180 V 4
Source Sense Input Pin Voltage VS1, VS2 -0.3 5 V 4
Operating Junction Temperature TJ -40 125 °C 4
VDD Turn-on Threshold VDD-ON 4 4.3 V VDD rising with 4.3 V / 1 ms 5
Turn-off Threshold VDD-OFF 3.6 3.8 V VDD < VDD-OFF 5
SR Gate Enable Threshold Voltage VDD-GATE-ON 6.5 7.1 V VDD > VDD-GATE-ON 5
SR Gate Disable Threshold Voltage VDD-GATE-OFF 5 6 V VDD < VDD-GATE-OFF 5
Operating Current IDD-OP1 8 10 mA fSW = 100 kHz, CGATE = 1 nF 5
Operating Current IDD-OP0 6 mA fSW = 100 kHz, CGATE = 0 nF 5
Start-up Current IDD-START 100 A VDD = VDD-ON − 0.1 V 5
Operating Current in Green Mode IDD-GREEN 100 210 A VDD = 12 V (no VD1/2 switching), GREEN1 enable at TJ = 25°C 5
Comparator Input Offset Voltage VOSI -1 0 1 mV 5
Drain Pin Leakage Current IDRAIN-LKG 1 A VD1/2 = 200 V 5
Minimum Off-time tOFF-MIN 1150 1550 2800 ns From VD1/2 higher than VTH-HGH 5
Turn-on Propagation Delay tON-DLY 30 80 ns From VD1/2 = −0.2 to VGATE = 1 V, when DLY_EN = 0 5
Turn-off Propagation Delay tOFF-DLY 30 80 ns From VD1/2 = 0.6 to VGATE = 5.7 V 5
Minimum SR Conduction Time to Enable SR when DLY_EN = 0 tGATE-SKIP1 500 710 ns Duration from turn-on trigger to VD1/2 rising higher than VTH-HGH, DLY_EN = 0 6
Adaptive Minimum On Time Ratio when DLY_EN = 0 KTON1 43 50 57 % DLY_EN = 0 & tSRCOND(n-1) = 8 s 6
Upper Limit of Minimum On-time when DLY_EN = 0 tMIN-ON-U1 4 5 6 s 200 ns < tMIN-ON < tMIN-ON-U1, DLY_EN = 0 6
Upper Limit of Minimum On-time when DLY_EN = 1 tMIN-ON-U2 2 2.5 3 s 200 ns < tMIN-ON < tMIN-ON-U2, DLY_EN = 1 6
SR Current Inversion Detection Window Ratio when DLY_EN = 0 KINV1 43 50 57 % KTON1 = KINV1, DLY_EN = 0; tINV-WIN = tMIN-ON 6
Minimum Switching Frequency fMIN 0 kHz 1 / (tSR-MAX-ON-CH1 + tSR-MAX-ON-CH2) 6
Maximum of Adaptive Offset Current IOFFSET 285 310 335 A VD1 = VD2 = 0 6
Non-switching Period of SR Gate to Enter Green Mode tGRN1-ENT 45 60 75 s SRCOND1, 2 both low for tGRN1-ENT; GREEN1 = HIGH 7
Non-switching Period of SR Gate to Reset VTH-OFF and Set DLY_EN tGRN2-ENT 4.5 6 7.5 s SRCOND1, 2 both low for tGRN2-ENT; generate GREEN2 pulse 7
Detection Window Time Ratio for Primary Shutdown Protection KSD-PRI 65 70 75 % LLD = 0, tVG1(n-1) = 8 s, K2ND-TOFF * tVG1(n-1) > tMIN-ON 7
Gate Clamping Voltage VGATE-MAX 9 10.5 12 V 12 V < VDD < 33 V, CGATE = 4.7 nF, TJ < TOTP1 7
Adaptive Gate Control Enabling Switching Period tHFS-EN 4 5 6.1 s Time from VGATE1(n-1) rising edge to VGATE1(n) rising edge at TJ < TOTP1 8
Rise Time tR 50 150 ns VDD = 12 V, CGATE = 3.3 nF, VGATE = 1 → 6 V at TJ = 25°C 8
Fall Time tF 30 50 ns VDD = 12 V, CGATE = 3.3 nF, VGATE = 6 → 1 V at TJ = 25°C 8
Thermal Resistance, Junction-to-Ambient (SOIC-8) RJA 165 °C/W SOIC-8; JESD51-2 and JESD51-3 (1s0p) 4
Thermal Characterization Parameter, Junction to Center of Top of Package (SOIC-8) RJT 22 °C/W SOIC-8; JESD51-2 and JESD51-3 4

CAD (KiCad official)

  • Symbol: NCP4318ALKDR2G
  • Footprint: Package_SO:SOIC-8_3.9x4.9mm_P1.27mm
  • 3D model: SOIC-8 (KiCad packages3D, STEP)
  • 3D model files: ncp4318alkdr2g-etched.step / ncp4318alkdr2g-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ncp4318alkdr2g.step / ncp4318alkdr2g.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: onsemi datasheet (24 pp, sha256 6e593a8dcde11a55, retrieved 2026-10-30, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF