3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownNCP4318AHJDR2G
onsemi · Gate Drive ICs · SOIC-8
NCP4318AHJDR2G from onsemi, in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GATE1 | output | Gate drive output for SR MOSFET1, with absolute maximum pin voltage of −0.3 to 17 V. |
| 2 | GND | power_in | Ground reference; all voltage ratings are with respect to this pin. |
| 3 | VS1 | input | Synchronous rectifier source sense input for SR1, recommended −0.3 to 5 V (absolute maximum −0.3 to 5.5 V). |
| 4 | VD1 | input | Synchronous rectifier drain sense input for SR1 (recommended −0.7 to 180 V, absolute maximum −4 to 200 V); IOFFSET1 current source flows out of this pin so an external series resistor can adjust the turn-off threshold, and it is off when VDD is under-voltage or switching is disabled in green mode. |
| 5 | VS2 | input | Synchronous rectifier source sense input for SR2, recommended −0.3 to 5 V (absolute maximum −0.3 to 5.5 V). |
| 6 | VD2 | input | Synchronous rectifier drain sense input for SR2 (recommended −0.7 to 180 V, absolute maximum −4 to 200 V); IOFFSET2 current source flows out of this pin so an external series resistor can adjust the turn-off threshold, and it is off when VDD is under-voltage or switching is disabled in green mode. |
| 7 | VDD | power_in | Supply voltage input, recommended 0 to 35 V (absolute maximum −0.3 to 37 V). |
| 8 | GATE2 | output | Gate drive output for SR MOSFET2, with absolute maximum pin voltage of −0.3 to 17 V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | onsemi |
| Package | SOIC-8 |
| Category | Power Supply Chip |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Power supply input pin voltage | VDD | -0.3 | 37 | V | 4 | ||
| Drain sense input pin voltage | VD1, VD2 | -4 | 200 | V | 4 | ||
| Gate drive output pin voltage | VGATE1, VGATE2 | -0.3 | 17 | V | 4 | ||
| Source sense input pin voltage | VS1, VS2 | -0.3 | 5.5 | V | 4 | ||
| Source sense input dynamic voltage | VS1-DYN, VS2-DYN | -4 | 5.5 | V | Pulse Width = 200 ns | 4 | |
| Power dissipation SOIC-8 | PD | 0.625 | W | TA = 25°C | 4 | ||
| Junction temperature | TJ | -40 | 150 | °C | 4 | ||
| Storage temperature range | TSTG | -60 | 150 | °C | 4 | ||
| Lead temperature | TL | 260 | °C | Soldering, 10 Seconds | 4 | ||
| ESD HBM (except VD1, VD2) | ESD | 3 | kV | Human Body Model, ANSI/ESDA/JEDEC JS-001-2012 | 4 | ||
| ESD CDM | ESD | 1 | kV | Charged Device Model, JESD22-C101 | 4 | ||
| Thermal resistance junction-to-ambient SOIC-8 | RθJA | 165 | °C/W | SOIC-8 (Note 3) | 4 | ||
| Thermal characterization parameter junction to top SOIC-8 | ΨJT | 22 | °C/W | SOIC-8 (Note 3) | 4 | ||
| VDD supply voltage | VDD | 0 | 35 | V | VDD pin to GND (Note 5) | 4 | |
| Drain sense input voltage | VD1, VD2 | -0.7 | 180 | V | 4 | ||
| Source sense input voltage | VS1, VS2 | -0.3 | 5 | V | 4 | ||
| Operating junction temperature | TJ | -40 | 125 | °C | 4 | ||
| Turn-on threshold | VDD-ON | 4 | 4.3 | V | VDD rising with 4.3 V / 1 ms | 5 | |
| Turn-off threshold | VDD-OFF | 3.6 | 3.8 | V | VDD < VDD-OFF | 5 | |
| SR gate enable threshold voltage | VDD-GATE-ON | 6.5 | 7.1 | V | VDD > VDD-GATE-ON | 5 | |
| SR gate disable threshold voltage | VDD-GATE-OFF | 5 | 6 | V | VDD < VDD-GATE-OFF | 5 | |
| Operating current | IDD-OP1 | 8 | 10 | mA | fSW = 100 kHz, CGATE = 1 nF | 5 | |
| Operating current | IDD-OP0 | 6 | mA | fSW = 100 kHz, CGATE = 0 nF | 5 | ||
| Start-up current | IDD-START | 100 | µA | VDD = VDD-ON - 0.1 V | 5 | ||
| Operating current in green mode | IDD-GREEN | 100 | 210 | µA | VDD = 12 V (no VD1/2 switching), GREEN1 enable at TJ = 25°C | 5 | |
| Comparator input offset voltage | VOSI | -1 | 0 | 1 | mV | 5 | |
| Drain pin leakage current | IDRAIN-LKG | 1 | µA | VD1/2 = 200 V | 5 | ||
| Minimum off-time | tOFF-MIN | 750 | 1150 | 1550 | ns | From VD1/2 higher than VTH-HGH, in AHD, AHJ | 5 |
| Turn-on propagation delay | tON-DLY | 30 | 80 | ns | From VD1/2 = -0.2 to VGATE = 1 V, when DLY_EN = 0 | 5 | |
| Turn-off propagation delay | tOFF-DLY | 30 | 80 | ns | From VD1/2 = 0.6 to VGATE = 5.7 V | 5 | |
| Minimum SR conduction time to enable SR, DLY_EN = 0 | tGATE-SKIP1 | 350 | 550 | ns | Turn-on trigger to VD1/2 rising higher than VTH-HGH, DLY_EN = 0, in AHD, AHJ | 6 | |
| Adaptive minimum on time ratio, DLY_EN = 0 | KTON1 | 43 | 50 | 57 | % | DLY_EN=0 & tSRCOND(n-1) = 8 µs, in AHJ | 6 |
| Upper limit of minimum on-time, DLY_EN = 0 | tMIN-ON-U1 | 4 | 5 | 6 | µs | 200 ns < tMIN-ON < tMIN-ON-U1, DLY_EN = 0 | 6 |
| Upper limit of minimum on-time, DLY_EN = 1 | tMIN-ON-U2 | 2 | 2.5 | 3 | µs | 200 ns < tMIN-ON < tMIN-ON-U2, DLY_EN = 1 | 6 |
| SR current inversion detection window ratio, DLY_EN = 0 | KINV1 | 43 | 50 | 57 | % | KTON1 = KINV1, DLY_EN = 0, tINV-WIN = tMIN-ON | 6 |
| Maximum of adaptive offset current | IOFFSET | 285 | 310 | 335 | µA | VD1 = VD2 = 0 | 6 |
| Non-switching period to enter green mode | tGRN1-ENT | 25 | 40 | 55 | µs | SRCOND1, 2 both low for tGRN1-ENT, in AHD, AHJ | 7 |
| Non-switching period to reset VTH-OFF and set DLY_EN | tGRN2-ENT | 2.5 | 4 | 5.5 | µs | SRCOND1, 2 both low for tGRN2-ENT, in AHD, AHJ | 7 |
| Detection window time ratio for primary shutdown protection | KSD-PRI | 65 | 70 | 75 | % | LLD = 0, tVG1(n-1) = 8 µs | 7 |
| Gate clamping voltage | VGATE-MAX | 9 | 10.5 | 12 | V | 12 V < VDD < 33 V, CGATE = 4.7 nF at TJ < TOTP1 | 7 |
| Rise time | tR | 50 | 150 | ns | VDD = 12 V, CGATE = 3.3 nF, VGATE = 1 → 6 V at TJ = 25°C | 8 | |
| Fall time | tF | 30 | 50 | ns | VDD = 12 V, CGATE = 3.3 nF, VGATE = 6 → 1 V at TJ = 25°C | 8 | |
| Turn-on threshold | VTH-ON | -100 | mV | ROFFSET = 0 Ω (includes comparator input offset voltage) | 5 | ||
| Minimum turn-off threshold voltage | VTH-OFF-MIN | -14 | mV | ROFFSET = 0 Ω, in AHD, AHJ, ALGP | 5 | ||
| Step size of adaptive turn-off threshold | VTH-OFF-STEP | 4 | mV | ROFFSET = 0 Ω, in AHD, AHJ | 5 | ||
| Maximum turn-off threshold voltage | VTH-OFF-MAX | 110 | mV | ROFFSET = 0 Ω, in AHD, AHJ, ALGP | 5 | ||
| Reset value of turn-off threshold voltage | VTH-OFF-RST | -10 | mV | ROFFSET = 0 Ω, in AHJ, ALGP | 5 | ||
| Drain voltage high detect threshold | VTH-HGH | 0.85 | V | VD1/2 rising | 6 | ||
| Turn-on de-bounce time with additional delay | tON-DLY2 | 240 | ns | DLY_EN = 1, in AHJ | 5 | ||
| Lower band of dead time regulation | tDEAD-LBAND | 170 | ns | From VGATE falling below VGATE-LOW, in AHD, AHJ | 6 | ||
| Debounce time of SR current inversion detection | tINV | 170 | ns | VGATE1/2 > 4.5 V & VD1/2 > VSRCINV for tINV, in AHD, AHJ, ALGP | 7 | ||
| Drain threshold for primary shutdown protection | VSD-PRI | 100 | mV | in AHD, AHJ | 7 | ||
| Abnormal VD sensing protection threshold | VABN-VD | 0.85 | V | VABN-VD = VTH-HGH, in AHJ | 7 | ||
| Over temperature protection reducing VGATE | TOTP1 | 105 | °C | TJ > TOTP1 & VGATE=6.7V, in AHJ | 7 | ||
| Over temperature protection stopping gate operation | TOTP2 | 140 | °C | TJ > TOTP2 & No gate output, in AHJ | 7 | ||
| Peak sourcing current of gate driver | ISOURCE | 1.5 | A | 8 | |||
| Peak sinking current of gate driver | ISINK | 4.5 | A | 8 |
CAD (KiCad official)
- Symbol:
NCP4318AHJDR2G - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SOIC-8 (KiCad packages3D, STEP)
- 3D model files:
ncp4318ahjdr2g-etched.step/ncp4318ahjdr2g-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ncp4318ahjdr2g.step/ncp4318ahjdr2g.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: onsemi datasheet (24 pp, sha256
6e593a8dcde11a55, retrieved 2026-10-27, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).