3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownNCP3066MNTXG
onsemi · LED Drivers · DFN-8-EP(4x4)
NCP3066MNTXG from onsemi, in a DFN-8-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | Switch Collector | passive | Internal Darlington switch collector, rated -0.3 to +42 V with switch current up to 1.5 A. |
| 2 | Switch Emitter | passive | Internal Darlington switch emitter, rated -0.6 V to VCC when the transistor is off. |
| 3 | Timing Capacitor | passive | Timing capacitor pin that sets the switching frequency, with pin voltage rated -0.2 to +1.4 V. |
| 4 | GND | power_in | Ground pin for all internal circuits; the EP flag must be tied to this pin on the PCB. |
| 5 | Comparator Inverting Input | input | Inverting input of the internal comparator with 235 mV threshold, rated -0.3 V to VCC. |
| 6 | VCC | power_in | Voltage supply pin, operating range 3.0 V to 40 V, absolute maximum 0 to +42 V. |
| 7 | Ipk Sense | input | Peak current sense input that monitors the voltage drop across an external resistor to limit peak current, with a 200 mV nominal threshold relative to VCC. |
| 8 | ON/OFF | input | ON/OFF pin; pulling it below 0.8 V or leaving it floating disables the device, and above 2.4 V (max 25 V) enables it. |
| 9 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | onsemi |
| Package | DFN-8-EP(4x4) |
| Category | Display Modules / LED Drivers / Display Drivers |
| Pins | 9 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VCC supply voltage | VCC | 0 | 42 | V | Measured vs. Pin 4 | 3 | |
| Darlington switch collector voltage | VSWC | -0.3 | 42 | V | Pin 1 | 3 | |
| Darlington switch collector to emitter voltage | VSWCE | -0.3 | 42 | V | Pins 1-2 | 3 | |
| Darlington switch current | ISW | 1.5 | A | 3 | |||
| Comparator inverting input voltage | VCII | -0.3 | V | Pin 5; upper limit printed as +VCC | 3 | ||
| Darlington switch emitter voltage (transistor OFF) | VSWE | -0.6 | V | Pin 2, transistor OFF; upper limit printed as +VCC | 3 | ||
| Ipk sense voltage | VIPK | -0.3 | V | Pin 7; upper limit printed as VCC+0.3 V | 3 | ||
| Timing capacitor pin voltage | VTC | -0.2 | 1.4 | V | Pin 3 | 3 | |
| ON/OFF pin voltage | VON/OFF | -0.3 | 25 | V | Printed as < VCC | 3 | |
| Lead temperature soldering | TSLD | 260 | °C | 3 | |||
| Storage temperature range | TSTG | -65 | 150 | °C | 3 | ||
| Maximum junction temperature | TJMAX | 150 | °C | 3 | |||
| Operating junction temperature range | TJ | 0 | 85 | °C | NCP3066 | 3 | |
| Thermal resistance junction-to-air, DFN-8 | RJA | 78 | °C/W | DFN−8 (Note 5: 35 m copper, 10 cm2 copper area) | 3 | ||
| Thermal resistance junction-to-case, DFN-8 | RJC | 14 | °C/W | DFN−8 | 3 | ||
| Oscillator frequency | fOSC | 110 | 150 | 190 | kHz | VPin5 = 0 V, CT = 2.2 nF, TJ = 25°C | 4 |
| Current limit sense voltage | VIPK(Sense) | 165 | 200 | 235 | mV | TJ = 25°C (Note 7) | 4 |
| Discharge to charge current ratio | IDISCHG/ICHG | 5.5 | 6 | 6.5 | − | Pin 7 to VCC, TJ = 25°C | 4 |
| Darlington switch collector to emitter voltage drop | VSWCE(DROP) | 1 | 1.3 | V | ISW = 1.0 A, TJ = 25°C (Note 6) | 4 | |
| Collector off-state current | IC(OFF) | 1 | 10 | A | VCE = 40 V | 4 | |
| Threshold voltage line regulation | REGLiNE | -6 | 2 | 6 | mV | VCC = 3.0 V to 40 V | 4 |
| Input bias current | ICII | -1000 | -100 | 1000 | nA | Vin = Vth | 4 |
| ON/OFF pin logic input level high | VIH | 2.2 | V | VOUT = 0 V, TJ = 25°C | 4 | ||
| ON/OFF pin logic input level high | VIH | 2.4 | V | VOUT = 0 V, TJ = 0°C to +85°C | 4 | ||
| ON/OFF pin logic input level low | VIL | 1 | V | VOUT = Nominal Output Voltage, TJ = 25°C | 4 | ||
| ON/OFF pin logic input level low | VIL | 0.8 | V | VOUT = Nominal Output Voltage, TJ = 0°C to +85°C | 4 | ||
| ON/OFF pin input current high | IIH | 15 | A | ON/OFF Pin = 5 V (ON), TJ = 25°C | 4 | ||
| ON/OFF pin input current low | IIL | 1 | A | ON/OFF Pin = 0 V (OFF), TJ = 25°C | 4 | ||
| ON/OFF pin minimum width | TON_MIN | 50 | s | TJ = 25°C | 4 | ||
| Supply current | ICC | 7 | mA | VCC = 5.0 V to 40 V, CT = 2.2 nF, Pin 7 = VCC, VPin 5 > Vth, Pin 2 = GND, remaining pins open | 4 | ||
| Standby quiescent current | ISTBY | 85 | 120 | A | ON/OFF Pin = 5.0 V (OFF), TJ = 25°C | 4 | |
| Standby quiescent current | ISTBY | 120 | A | ON/OFF Pin = 5.0 V (OFF), TJ = −40°C to +125°C | 4 | ||
| Threshold voltage tolerance | VTH | -5 | 5 | % | TJ = 0°C to 85°C, nominal 235 mV | 4 | |
| Threshold voltage tolerance | VTH | -10 | 10 | % | TJ = −40°C to +125°C, nominal 235 mV | 4 | |
| Threshold voltage | VTH | 235 | mV | TJ = 25°C | 4 | ||
| Thermal shutdown threshold | TSHD | 160 | °C | 4 | |||
| Thermal shutdown hysteresis | TSHDHYS | 10 | °C | 4 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | 4. The pins which are not defined may not be loaded by external signals. 5. 35 m copper, 10 cm2 copper area. | 3 |
CAD (KiCad official)
- Symbol:
NCP3066MNTXG - Footprint:
Package_DFN_QFN:DFN-8-1EP_4x4mm_P0.8mm_EP2.5x3.6mm - 3D model: DFN-8-EP(4x4) (KiCad packages3D, STEP)
- 3D model files:
ncp3066mntxg-etched.step/ncp3066mntxg-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ncp3066mntxg.step/ncp3066mntxg.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: onsemi datasheet (20 pp, sha256
f3f39aff95d13b06, retrieved 2026-11-07, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).