main
Ray
Publish 0.1.0
91b9293
NCP1612ADR2G
onsemi · AC-DC Controllers & Regulators · SOP-10
NCP1612ADR2G from onsemi, in a SOP-10. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | FOVP | input | Fast over-voltage protection input that disables the driver when Vpin1 exceeds the FOVP threshold (2% above the soft OVP reference), also used for UVP2 and BUV detection on A/A1/A3/B versions, with a 250 nA internal sink current to ground if open; absolute maximum -0.3 to +10 V. |
| 2 | Feedback | input | Receives a portion of the PFC output voltage for regulation, the Dynamic Response Enhancer, soft OVP (above 105% of VREF) and UVP (below 12% of VREF), with a 250 nA internal sink current that disables the part if open; absolute maximum -0.3 to +10 V. |
| 3 | VCONTROL | output | Error amplifier output where the network to ground sets the regulation loop bandwidth (typically below 20 Hz) and provides soft-start by charging up from ground at startup. |
| 4 | VSENSE | input | Senses a portion of the instantaneous input voltage for brown-out detection (stops below 0.9 V for more than 50 ms, resumes above 1 V) and line range detection (high-line above 2.2 V, low-line below 1.7 V for more than 25 ms); recommended maximum 4.5 V. |
| 5 | FFcontrol | output | Sources a current representative of the line current into a resistor to ground, setting critical conduction mode above the 2.5 V reference and a longer dead-time below it, with cycle skipping below 0.65 V. |
| 6 | CS/ZCD | input | Monitors the MOSFET current for maximum current limiting and, through the auxiliary winding via a diode, detects zero current (core reset); absolute maximum -0.3 to +35 V with +5 mA injected current. |
| 7 | GND | power_in | Ground pin to be connected to the PFC stage ground. |
| 8 | DRV | output | Totem-pole gate drive output with -0.5/+0.8 A capability for driving high gate charge power MOSFETs. |
| 9 | VCC | power_in | Positive supply of the IC with operating range 9.5 V up to 35 V after start-up, starting at 10.5 V (A, A1, A2, A3) or 17.0 V (B, B2) and turning off below 9.0 V (typical values). |
| 10 | pfcOK | output | Grounded until the PFC output reaches its nominal level or when a fault is detected and high impedance otherwise; NCP1612A, A1, A3 and B latch off if Vpin10 exceeds 7.5 V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | onsemi |
| Package | SOP-10 |
| Category | Power Management |
| Pins | 10 |
CAD (KiCad official)
- Symbol:
NCP1612ADR2G - Footprint:
Package_SO:SOIC-10_3.9x4.9mm_P1mm - 3D model: SOP-10, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 1.75 mm nominal SOIC height). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions are nominal, not the manufacturer's CAD (STEP)
- 3D model files:
ncp1612adr2g-etched.step/ncp1612adr2g-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ncp1612adr2g.step/ncp1612adr2g.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: onsemi datasheet (33 pp, sha256
41e7fb35aef7ffc6, retrieved 2026-10-30, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(vision), consensusclaude-opus-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# NCP1612ADR2G
**onsemi** · AC-DC Controllers & Regulators · SOP-10
NCP1612ADR2G from onsemi, in a SOP-10. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | FOVP | input | Fast over-voltage protection input that disables the driver when Vpin1 exceeds the FOVP threshold (2% above the soft OVP reference), also used for UVP2 and BUV detection on A/A1/A3/B versions, with a 250 nA internal sink current to ground if open; absolute maximum -0.3 to +10 V. |
| 2 | Feedback | input | Receives a portion of the PFC output voltage for regulation, the Dynamic Response Enhancer, soft OVP (above 105% of VREF) and UVP (below 12% of VREF), with a 250 nA internal sink current that disables the part if open; absolute maximum -0.3 to +10 V. |
| 3 | VCONTROL | output | Error amplifier output where the network to ground sets the regulation loop bandwidth (typically below 20 Hz) and provides soft-start by charging up from ground at startup. |
| 4 | VSENSE | input | Senses a portion of the instantaneous input voltage for brown-out detection (stops below 0.9 V for more than 50 ms, resumes above 1 V) and line range detection (high-line above 2.2 V, low-line below 1.7 V for more than 25 ms); recommended maximum 4.5 V. |
| 5 | FFcontrol | output | Sources a current representative of the line current into a resistor to ground, setting critical conduction mode above the 2.5 V reference and a longer dead-time below it, with cycle skipping below 0.65 V. |
| 6 | CS/ZCD | input | Monitors the MOSFET current for maximum current limiting and, through the auxiliary winding via a diode, detects zero current (core reset); absolute maximum -0.3 to +35 V with +5 mA injected current. |
| 7 | GND | power_in | Ground pin to be connected to the PFC stage ground. |
| 8 | DRV | output | Totem-pole gate drive output with -0.5/+0.8 A capability for driving high gate charge power MOSFETs. |
| 9 | VCC | power_in | Positive supply of the IC with operating range 9.5 V up to 35 V after start-up, starting at 10.5 V (A, A1, A2, A3) or 17.0 V (B, B2) and turning off below 9.0 V (typical values). |
| 10 | pfcOK | output | Grounded until the PFC output reaches its nominal level or when a fault is detected and high impedance otherwise; NCP1612A, A1, A3 and B latch off if Vpin10 exceeds 7.5 V. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | onsemi |
| Package | SOP-10 |
| Category | Power Management |
| Pins | 10 |
## CAD (KiCad official)
- Symbol: `NCP1612ADR2G`
- Footprint: `Package_SO:SOIC-10_3.9x4.9mm_P1mm`
- 3D model: SOP-10, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 1.75 mm nominal SOIC height). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions are nominal, not the manufacturer's CAD (STEP)
- 3D model files: `ncp1612adr2g-etched.step` / `ncp1612adr2g-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `ncp1612adr2g.step` / `ncp1612adr2g.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [onsemi datasheet](docs/ncp1612adr2g-datasheet.pdf) (33 pp, sha256 `41e7fb35aef7ffc6`, retrieved 2026-10-30, tier: lcsc)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (vision), consensus `claude-opus-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/ncp1612adr2g-datasheet.pdf)