Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

NCP1608BDR2G

onsemi · AC-DC Controllers and Regulators · SOIC-8

NCP1608BDR2G from onsemi, in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 FB input Inverting input of the internal transconductance error amplifier. A resistor divider scales VOUT to the internal 2.5 V VREF for regulation. Also used for OVP (~106% VREF) and UVP (VUVP ~0.31 V) protections; controller disables when forced above VOVP or below VUVP.
2 Control output Output of the internal error amplifier. A compensation network (typically Ccomp to GND) is connected here to set the loop bandwidth; low bandwidth yields high power factor and low THD. Control voltage range ~4.5-5.3 V above Ct offset.
3 Ct passive Timing capacitor pin. Sources ~275 µA (Icharge) to charge an external timing capacitor; on-time ends when Ct reaches an internal voltage derived from VControl. Ct is then discharged (~50 ns) at end of on-time. VCt(MAX) ~4.93 V.
4 CS input Current sense input for cycle-by-cycle current limiting through the power switch. When VCS exceeds VILIM (typ 0.5 V), the DRV output turns off. External sense resistor programs the maximum switch current; leading-edge blanking ~190 ns.
5 ZCD input Zero Current Detection input. Senses the voltage of an auxiliary (NZCD) winding to detect boost-inductor demagnetization for CrM operation. Arming threshold ~1.4 V, triggering ~0.7 V; internal clamps at ~+10 V / −0.7 V protect the pin.
6 GND power_in Analog ground reference for the controller. All signal thresholds and the VCC supply are referenced to this pin.
7 DRV output Totem-pole gate driver output for the external power MOSFET. Typical source impedance 12 Ω (500 mA source) and sink impedance 6 Ω (800 mA sink). Rise/fall times ~35/25 ns; internally clamped for MOSFET gate protection.
8 VCC power_in Positive supply for the controller. Enables when VCC exceeds VCC(on) (typ 12 V) and disables when VCC drops below VCC(off) (typ 9.5 V); UVLO hysteresis ~2.5 V. Absolute max 20 V; startup current ≤35 µA.

Key specifications

Parameter Value
Manufacturer onsemi
Package SOIC-8
Category PMIC
Pins 8

Ordering variants

Same part, different packaging or reel option.

  • NCP1608BDR2G

CAD (KiCad official)

  • Symbol: NCP1608BDR2G
  • Footprint: Package_SO:SOIC-8_3.9x4.9mm_P1.27mm
  • 3D model: SOIC-8 (KiCad packages3D, STEP)
  • 3D model files: ncp1608bdr2g-etched.step / ncp1608bdr2g-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ncp1608bdr2g.step / ncp1608bdr2g.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: onsemi datasheet (24 pp, sha256 425a342161af0228, retrieved 2026-08-17, tier: manufacturer)
  • Extractor: ds2sf (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF