← Commit history

ncp1397bdr2g: restore the component block (pinout + model declarations) from this page's own README and symbol

Ray ·0811d9cce9 · ·parent ba22bca
1 file changed +123−1
page.json+123−1
@@ -33,5 +33,127 @@   "author": {     "name": "Ray",     "email": "[email protected]"+  },+  "component": {+    "mpn": "NCP1397BDR2G",+    "manufacturer": "onsemi",+    "package": "SOIC-16",+    "pin_count": 16,+    "category": "AC-DC Controllers and Regulators",+    "datasheet": "https://www.onsemi.com/pdf/datasheet/ncp1397b-d.pdf",+    "parts": {+      "symbol": "ncp1397bdr2g.kicad_sym",+      "footprint": "ncp1397bdr2g.kicad_mod",+      "model_3d": "ncp1397bdr2g-etched.glb",+      "model_3d_plain": "ncp1397bdr2g.glb",+      "model_3d_step": "ncp1397bdr2g-etched.step",+      "model_3d_step_plain": "ncp1397bdr2g.step",+      "lbr": "ncp1397bdr2g.lbr"+    },+    "pins": [+      {+        "number": "1",+        "name": "CSS(dis)",+        "type": "passive",+        "description": "Soft-start capacitor discharge pin. Connect to the external soft-start capacitor to reset (discharge) it before startup or during overload conditions so the next startup ramp begins from zero."+      },+      {+        "number": "2",+        "name": "Fmax",+        "type": "passive",+        "description": "Maximum frequency clamp. A resistor to this pin sets the upper frequency excursion of the VCO (VCO range up to 500 kHz)."+      },+      {+        "number": "3",+        "name": "Ctimer",+        "type": "passive",+        "description": "Fault timer duration. An external capacitor to GND sets the duration the controller tolerates a fault at the Fault pin before shutting down."+      },+      {+        "number": "4",+        "name": "Rt",+        "type": "passive",+        "description": "Minimum frequency clamp. A resistor to this pin sets the minimum oscillator frequency reached when VFB = 1 V (lower limit of the VCO sweep, typically ≥50 kHz)."+      },+      {+        "number": "5",+        "name": "BO",+        "type": "input",+        "description": "Brown-out detection input. Senses a scaled image of the bulk voltage; when the pin is driven above Vlatch (~4 V) the controller fully latches off, providing brown-out and PFC-association protection."+      },+      {+        "number": "6",+        "name": "FB",+        "type": "input",+        "description": "Feedback input. Injecting current (typically from an optocoupler in common-collector configuration) into this pin increases the oscillation frequency up to Fmax, providing loop regulation."+      },+      {+        "number": "7",+        "name": "DT",+        "type": "passive",+        "description": "Deadtime adjustment. A single resistor to GND sets the half-bridge dead-time between high-side and low-side conduction, adjustable from ~100 ns to 2 µs to prevent shoot-through."+      },+      {+        "number": "8",+        "name": "Skip/Disable",+        "type": "input",+        "description": "Skip or Disable input. Pulling low enters skip/disable; upon release a clean soft-start sequence occurs if VFB < 0.3 V, otherwise the IC restarts without soft-start (skip-cycle mode)."+      },+      {+        "number": "9",+        "name": "Fault",+        "type": "input",+        "description": "Fault detection input. When asserted above the first threshold the external timer (Ctimer) starts counting down and shuts down the controller; the soft-start discharge switch is simultaneously activated so operating frequency rises to protect the power stage. A second higher threshold (~1.5 V) latches the IC off permanently on the 'B' variant (NCP1397B)."+      },+      {+        "number": "10",+        "name": "GND",+        "type": "power_in",+        "description": "Analog ground reference for the controller and low-side driver return."+      },+      {+        "number": "11",+        "name": "Mlower",+        "type": "output",+        "description": "Low-side gate driver output. Drives the gate of the lower half-bridge MOSFET, referenced to GND, with 1 A sink / 0.5 A source peak capability."+      },+      {+        "number": "12",+        "name": "VCC",+        "type": "power_in",+        "description": "Controller supply pin. Accepts up to 20 V; typical startup current is 300 µA. Decouple with a local ceramic capacitor to GND."+      },+      {+        "number": "13",+        "name": "NC",+        "type": "unconnected",+        "description": "Pin 13 is omitted from the package (SO-16 'Less Pin 13'). Its absence increases the creepage distance between the low-voltage (VCC, pin 12) and high-voltage floating (HB, pin 14) sections."+      },+      {+        "number": "14",+        "name": "HB",+        "type": "passive",+        "description": "Half-bridge switching node connection. Return/reference for the high-side driver and bootstrap capacitor; connects to the source of the upper MOSFET / drain of the lower MOSFET (switching node up to 600 V)."+      },+      {+        "number": "15",+        "name": "Mupper",+        "type": "output",+        "description": "High-side gate driver output. Drives the gate of the upper half-bridge MOSFET, floating between HB and Vboot; 1 A sink / 0.5 A source peak capability."+      },+      {+        "number": "16",+        "name": "Vboot",+        "type": "power_in",+        "description": "Bootstrap supply pin for the high-side floating driver. Connect a bootstrap capacitor between Vboot and HB (charged from VCC via an external bootstrap diode) to supply the upper gate driver."+      }+    ],+    "provenance": {+      "rebuilt": "component block rebuilt 2026-10-05 from this page's own README pinout table and .kicad_sym (pins cross-checked), no re-extraction"+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }   }-}\ No newline at end of file+}