← Commit history
README.mdadded+56@@ -0,0 +1,56 @@+# NCP1397BDR2G++**onsemi** · AC-DC Controllers and Regulators · SOIC-16++NCP1397BDR2G from onsemi, in a SOIC-16. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | CSS(dis) | passive | Soft-start capacitor discharge pin. Connect to the external soft-start capacitor to reset (discharge) it before startup or during overload conditions so the next startup ramp begins from zero. |+| 2 | Fmax | passive | Maximum frequency clamp. A resistor to this pin sets the upper frequency excursion of the VCO (VCO range up to 500 kHz). |+| 3 | Ctimer | passive | Fault timer duration. An external capacitor to GND sets the duration the controller tolerates a fault at the Fault pin before shutting down. |+| 4 | Rt | passive | Minimum frequency clamp. A resistor to this pin sets the minimum oscillator frequency reached when VFB = 1 V (lower limit of the VCO sweep, typically ≥50 kHz). |+| 5 | BO | input | Brown-out detection input. Senses a scaled image of the bulk voltage; when the pin is driven above Vlatch (~4 V) the controller fully latches off, providing brown-out and PFC-association protection. |+| 6 | FB | input | Feedback input. Injecting current (typically from an optocoupler in common-collector configuration) into this pin increases the oscillation frequency up to Fmax, providing loop regulation. |+| 7 | DT | passive | Deadtime adjustment. A single resistor to GND sets the half-bridge dead-time between high-side and low-side conduction, adjustable from ~100 ns to 2 µs to prevent shoot-through. |+| 8 | Skip/Disable | input | Skip or Disable input. Pulling low enters skip/disable; upon release a clean soft-start sequence occurs if VFB < 0.3 V, otherwise the IC restarts without soft-start (skip-cycle mode). |+| 9 | Fault | input | Fault detection input. When asserted above the first threshold the external timer (Ctimer) starts counting down and shuts down the controller; the soft-start discharge switch is simultaneously activated so operating frequency rises to protect the power stage. A second higher threshold (~1.5 V) latches the IC off permanently on the 'B' variant (NCP1397B). |+| 10 | GND | power_in | Analog ground reference for the controller and low-side driver return. |+| 11 | Mlower | output | Low-side gate driver output. Drives the gate of the lower half-bridge MOSFET, referenced to GND, with 1 A sink / 0.5 A source peak capability. |+| 12 | VCC | power_in | Controller supply pin. Accepts up to 20 V; typical startup current is 300 µA. Decouple with a local ceramic capacitor to GND. |+| 13 | NC | unconnected | Pin 13 is omitted from the package (SO-16 'Less Pin 13'). Its absence increases the creepage distance between the low-voltage (VCC, pin 12) and high-voltage floating (HB, pin 14) sections. |+| 14 | HB | passive | Half-bridge switching node connection. Return/reference for the high-side driver and bootstrap capacitor; connects to the source of the upper MOSFET / drain of the lower MOSFET (switching node up to 600 V). |+| 15 | Mupper | output | High-side gate driver output. Drives the gate of the upper half-bridge MOSFET, floating between HB and Vboot; 1 A sink / 0.5 A source peak capability. |+| 16 | Vboot | power_in | Bootstrap supply pin for the high-side floating driver. Connect a bootstrap capacitor between Vboot and HB (charged from VCC via an external bootstrap diode) to supply the upper gate driver. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | onsemi |+| Package | SOIC-16 |+| Category | PMIC |+| Pins | 16 |++## Ordering variants++- `NCP1397BDR2GADR2G`+- `NCP1397BDR2G`++## CAD (KiCad official)++- Symbol: `NCP1397BDR2G`+- Footprint: `Package_SO:SOIC-16_3.9x9.9mm_P1.27mm`+- 3D model: SOIC-16 (KiCad packages3D, STEP)++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [onsemi datasheet](https://www.onsemi.com/pdf/datasheet/ncp1397b-d.pdf) (None pp, sha256 `cee5e90dc431cbdf`, retrieved 2026-08-17, tier: manufacturer)+- **Extractor:** `ds2sf` (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/ncp1397bdr2g-datasheet.pdf)
page.jsonadded+34@@ -0,0 +1,34 @@+{+ "slug": "ncp1397bdr2g",+ "version": "0.1.0",+ "type": "component",+ "description": "onsemi AC-DC Controllers and Regulators, SOIC-16. Datasheet-verified pinout, KiCad symbol/footprint/3D.",+ "tags": [+ "component",+ "pmic",+ "ncp1397bdr2g"+ ],+ "dependencies": {},+ "hero": {+ "type": "image",+ "path": "docs/hero.png"+ },+ "files": [+ "page.json",+ "README.md",+ "ncp1397bdr2g.kicad_sym",+ "ncp1397bdr2g.kicad_mod",+ "ncp1397bdr2g.glb",+ "ncp1397bdr2g.step",+ "ncp1397bdr2g.lbr",+ "docs/hero.png",+ "docs/ncp1397bdr2g-datasheet.pdf",+ "viewers/symbol.html",+ "viewers/footprint.html"+ ],+ "visibility": "public",+ "author": {+ "name": "Ray",+ "email": "[email protected]"+ }+}