component
NCP1200D100R2G
Public Made by Adomby adom
onsemi AC-DC Controllers and Regulators, SOIC-8. Datasheet-verified pinout, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads on click. Unloads only if this page sits in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads on click. Unloads only if this page sits in the background.
PCB Footprint
Open full view ↗Loads on click. Unloads only if this page sits in the background.
Datasheet
Open in new tab ↗Loads on click. Unloads only if this page sits in the background.
README
markdownNCP1200D100R2G
onsemi · AC-DC Controllers and Regulators · SOIC-8
NCP1200D100R2G from onsemi, in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | Adj | input | Skip-cycle peak-current adjust. Sets the level below which the controller enters skip-cycle mode for light-load efficiency. Default Vskip ~1.4 V; internal output impedance ~25 kOhm. |
| 2 | FB | input | Feedback input; connect an optocoupler collector here to adjust the peak-current setpoint according to output power demand. Internally pulled up (Rup ~8 kOhm) to internal reference; FB-to-Ipk division ratio ~4. |
| 3 | CS | input | Current sense input. Senses the primary switch current via a sense resistor and routes it through a 250 ns leading-edge blanking network to the internal PWM comparator. Max internal current setpoint ~1.0 V. |
| 4 | GND | power_in | IC ground reference for all internal circuitry. |
| 5 | Drv | output | Gate drive output to an external MOSFET or IGBT. +/-250 mA peak source/sink; Roh ~40 Ohm (typ), Rol ~12 Ohm (typ). Rise ~67 ns, fall ~28 ns into 1 nF. |
| 6 | VCC | power_in | Supply pin for the IC. Connect an external bulk capacitor of typically 10 uF. UVLO: VCCON ~9.8 V (start), VCCOFF ~11.4 V (stop during dynamic self-supply). Absolute max 16 V. |
| 7 | NC | unconnected | No connection. Left un-connected to ensure adequate creepage distance between the low-voltage side (VCC) and the high-voltage HV pin. |
| 8 | HV | power_in | High-voltage start-up / self-supply pin. Connect directly to the rectified high-voltage rail; injects a constant current (~4 mA) into the VCC bulk cap to eliminate the auxiliary winding. Minimum operating voltage 30 V; max 450 V (VCC grounded) or 500 V (VCC decoupled with 10 uF). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | onsemi |
| Package | SOIC-8 |
| Category | PMIC |
| Pins | 8 |
Ordering variants
Same part, different packaging or reel option.
NCP1200D100R2GNCP1200D100R2GP100G
CAD (KiCad official)
- Symbol:
NCP1200D100R2G - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SOIC-8 (KiCad packages3D, STEP)
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: onsemi datasheet (18 pp, sha256
6af2476d5e861a8b, retrieved 2026-08-17, tier: lcsc) - Extractor:
ds2sf(Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate. - CAD: KiCad official libraries (CC-BY-SA 4.0).