main
Ray Brief states the pinout check that actually ran (was an unconditional "Datasheet-verified pinout") 14423ab
{
  "schema_version": 1,
  "type": "component",
  "slug": "ncn8026amntxg",
  "title": "NCN8026AMNTXG",
  "brief": "onsemi Interface - Specialized, QFN-24-EP(4x4). Pinout extracted from the datasheet, KiCad symbol/footprint/3D.",
  "version": "0.1.0",
  "license": "CC-BY-SA-4.0",
  "tags": [
    "component",
    "communication interface chip-uart-485-232",
    "ncn8026amntxg"
  ],
  "component": {
    "mpn": "NCN8026AMNTXG",
    "manufacturer": "onsemi",
    "package": "QFN-24-EP(4x4)",
    "pin_count": 25,
    "category": "Communication Interface Chip/UART/485/232",
    "subcategory": "Interface - Specialized",
    "datasheet": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588930615567245312",
    "parts": {
      "symbol": "ncn8026amntxg.kicad_sym",
      "footprint": "ncn8026amntxg.kicad_mod",
      "model_3d": "ncn8026amntxg.glb",
      "model_3d_step": "ncn8026amntxg.step",
      "lbr": "ncn8026amntxg.lbr"
    },
    "distributor_links": {},
    "pins": [
      {
        "number": "1",
        "name": "VSEL0",
        "type": "input",
        "description": "Card VCC voltage-select bit 0. Combined with VSEL1 selects 5 V, 3 V or 1.8 V (5V/3V mode when VSEL0=Low; 1.8V/3V mode when VSEL0=High; VSEL1 selects between the two levels of the chosen mode)."
      },
      {
        "number": "2",
        "name": "CS",
        "type": "input",
        "description": "Active-low chip select. When CS is Low the control and signal pins are configured normally; when CS is High, CMDVCC, VSEL0, VSEL1, CLKDIV1, CLKDIV2 and RSTIN are latched, and I/Ouc, AUX1uc, AUX2uc go to high-impedance pull-up."
      },
      {
        "number": "3",
        "name": "VDDP",
        "type": "power_in",
        "description": "Regulator power supply (2.7-5.5 V depending on selected CVCC mode). When VDDP falls below ~2.5 V the card pins are disabled."
      },
      {
        "number": "4",
        "name": "PRES",
        "type": "input",
        "description": "Active-low card-presence input (card present when PRES=Low) with an ~8 ms built-in debounce timer. Intended for normally-open (NO) smart-card connectors; may be left open when unused."
      },
      {
        "number": "5",
        "name": "PRES",
        "type": "input",
        "description": "Active-high card-presence input (card present when PRES=High) with an ~8 ms built-in debounce timer. Intended for normally-closed (NC) smart-card connectors; may be left open when unused."
      },
      {
        "number": "6",
        "name": "CI/O",
        "type": "bidirectional",
        "description": "Bidirectional level-shifted I/O to smart-card connector pin C7. Internal ~11 kΩ pull-up to CVCC provides high-impedance idle state for the card I/O line."
      },
      {
        "number": "7",
        "name": "CAUX2",
        "type": "bidirectional",
        "description": "Bidirectional level-shifted auxiliary AUX2 I/O to smart-card connector pin C8. Internal ~11 kΩ pull-up to CVCC provides high-impedance idle state."
      },
      {
        "number": "8",
        "name": "CAUX1",
        "type": "bidirectional",
        "description": "Bidirectional level-shifted auxiliary AUX1 I/O to smart-card connector pin C4. Internal ~11 kΩ pull-up to CVCC provides high-impedance idle state."
      },
      {
        "number": "9",
        "name": "CCLK",
        "type": "output",
        "description": "Smart-card clock output (drives card pin C3). Derived from CLKIN through the internal clock divider and level shifter; supports up to 27 MHz."
      },
      {
        "number": "10",
        "name": "CRST",
        "type": "output",
        "description": "Smart-card RESET output to card connector pin C2. Level-shifted from the host RSTIN signal to CVCC level."
      },
      {
        "number": "11",
        "name": "CVCC",
        "type": "power_out",
        "description": "Programmable card power-supply output (card pin C1). Delivers 1.8 V / 3.0 V / 5.0 V (±5%) at up to 70 mA, programmable via VSEL0/VSEL1. Requires an external distributed ceramic capacitor 80 nF-1.2 µF (ESR < 100 mΩ) between CVCC and CGND."
      },
      {
        "number": "12",
        "name": "PORADJ",
        "type": "input",
        "description": "Power-on-reset threshold adjustment input. External resistor divider on VDD sets the VDD UVLO / POR threshold (rising ~1.24 V, falling ~1.19 V typical at PORADJ). Tie to GND when unused."
      },
      {
        "number": "13",
        "name": "CMDVCC",
        "type": "input",
        "description": "Active-low command-VCC / activation-enable input. Toggling CMDVCC High→Low with a card present starts the ISO7816 activation sequence; when CMDVCC=High the CVCC output is pulled low and the internal LDO is disabled (unless latched by CS)."
      },
      {
        "number": "14",
        "name": "RSTIN",
        "type": "input",
        "description": "Host-side reset input, referenced to VDD. Level-shifted internally and driven to the smart card via CRST at the CVCC-programmed voltage."
      },
      {
        "number": "15",
        "name": "VDD",
        "type": "power_in",
        "description": "System-controller (host) power supply, 1.6-5.5 V. Sets the host-side logic-level of the level shifters. A 0.1 µF decoupling capacitor is required. When VDD falls below ~1.45 V the card pins are disabled."
      },
      {
        "number": "16",
        "name": "GND",
        "type": "power_in",
        "description": "Digital / host-side ground reference."
      },
      {
        "number": "17",
        "name": "INT",
        "type": "output",
        "description": "Active-low interrupt request to the host. Asserted on card-presence changes detected via PRES/PRES and on faults (e.g. CVCC overload). Open-drain-like output with an ~50 kΩ pull-up (available with metal-change option)."
      },
      {
        "number": "18",
        "name": "CLKIN",
        "type": "input",
        "description": "External clock input to the internal clock divider (up to 27 MHz). Divider ratio (1/1, 1/2, 1/4, 1/8) is selected by CLKDIV1/CLKDIV2 and produces CCLK to the card."
      },
      {
        "number": "19",
        "name": "I/Ouc",
        "type": "bidirectional",
        "description": "Host-side bidirectional I/O corresponding to card CI/O. Level-translated between the microcontroller (VDD domain) and the smart card (CVCC domain). Built-in ~11 kΩ pull-up provides high-impedance state."
      },
      {
        "number": "20",
        "name": "AUX1uc",
        "type": "bidirectional",
        "description": "Host-side bidirectional auxiliary line corresponding to card CAUX1 (C4). Level-translated between the microcontroller (VDD) and the card (CVCC); built-in ~11 kΩ pull-up."
      },
      {
        "number": "21",
        "name": "AUX2uc",
        "type": "bidirectional",
        "description": "Host-side bidirectional auxiliary line corresponding to card CAUX2 (C8). Level-translated between the microcontroller (VDD) and the card (CVCC); built-in ~11 kΩ pull-up."
      },
      {
        "number": "22",
        "name": "CLKDIV1",
        "type": "input",
        "description": "Clock-divider select bit 1. Combined with CLKDIV2 programs CCLK = CLKIN divided by 1, 1/2, 1/4 or 1/8 (see clock-division table)."
      },
      {
        "number": "23",
        "name": "CLKDIV2",
        "type": "input",
        "description": "Clock-divider select bit 2. Combined with CLKDIV1 programs the CLKIN→CCLK division ratio."
      },
      {
        "number": "24",
        "name": "VSEL1",
        "type": "input",
        "description": "Card VCC voltage-select bit 1. Combined with VSEL0 chooses CVCC = 5 V, 3 V or 1.8 V (VSEL1=High picks the higher level of the mode chosen by VSEL0)."
      },
      {
        "number": "25",
        "name": "GND",
        "type": "power_in",
        "description": "Exposed thermal pad - regulator (card-side) power-supply ground. Must be soldered to the PCB ground plane for proper electrical operation and thermal dissipation."
      }
    ],
    "provenance": {
      "extractor": "ds2sf",
      "datasheet": {
        "url": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588930615567245312",
        "pages": 15,
        "sha256": "c3d6be7a248da33b",
        "source_tier": "lcsc"
      },
      "cad": "KiCad official (CC-BY-SA 4.0)",
      "pins": {
        "total": 25,
        "described": 25,
        "cites_pages": true,
        "refuses_to_fabricate": true
      }
    },
    "viewers": {
      "symbol": "viewers/symbol.html",
      "footprint": "viewers/footprint.html"
    }
  },
  "metadata": {
    "specs": {
      "Manufacturer": "onsemi",
      "Package": "QFN-24-EP(4x4)",
      "Category": "Communication Interface Chip/UART/485/232",
      "Pins": "25"
    }
  },
  "variants": [
    {
      "mpn": "NCN8026AMNTXG",
      "kind": "packaging"
    }
  ],
  "sections": [
    "hero",
    "viewers",
    "readme",
    "breadcrumbs",
    "info"
  ],
  "discovery_triggers": [
    "ncn8026amntxg"
  ],
  "discovery_pitch": "NCN8026AMNTXG (onsemi) component page with datasheet-verified CAD.",
  "author": {
    "name": "Ray"
  },
  "dependencies": {},
  "hero": {
    "type": "image",
    "path": "docs/hero.png"
  },
  "files": [
    "page.json",
    "README.md",
    "ncn8026amntxg.kicad_sym",
    "ncn8026amntxg.kicad_mod",
    "ncn8026amntxg.glb",
    "ncn8026amntxg.step",
    "ncn8026amntxg.lbr",
    "docs/hero.png",
    "docs/ncn8026amntxg-datasheet.pdf",
    "viewers/symbol.html",
    "viewers/footprint.html"
  ],
  "visibility": {
    "public": true
  },
  "updated_at": "2026-09-25T02:51:39.884Z"
}