3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownNCL30186BDR2G
onsemi · LED Drivers · SOP-10
NCL30186BDR2G from onsemi, in a SOP-10. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | DIM | input | Used for analog or PWM dimming control; an analog signal varied between VDIM0 and VDIM100 or a PWM signal adjusts the LED current. |
| 2 | ZCD | input | Connected to the auxiliary winding, this pin detects the core reset event. |
| 3 | VS | power_in | Monitors the input voltage rail for power factor correction, valley lockout and brownout detection, with brownout declared if VS stays below VBO(off) of 0.9 V typical for more than the 25 ms blanking time. |
| 4 | COMP | passive | Receives a filtering capacitor for power factor correction, with typical values ranging from 1 to 4.7 µF. |
| 5 | SD | input | An NTC connected here programs the thermal current foldback threshold and slope, and a Zener diode can pull it up for adjustable OVP while stopping the controller. |
| 6 | CS | input | Monitors the primary peak current; the controller stops operating if the measured CS impedance at start-up does not exceed 120 Ω typically. |
| 7 | GND | power_in | Controller ground pin. |
| 8 | DRV | output | Driver output to an external MOSFET. |
| 9 | VCC | power_in | Positive supply of the IC; the circuit starts when VCC exceeds 18 V and turns off below 8.8 V (typical), with an operating range of 9.4 V up to 26 V after start-up. |
| 10 | NC | unconnected | Not connected. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | onsemi |
| Package | SOP-10 |
| Category | LED Drivers |
| Pins | 10 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Maximum power supply voltage VCC continuous | VCC(MAX) | -0.3 | 30 | V | VCC pin, continuous voltage | 5 | |
| Maximum driver pin voltage DRV continuous | VDRV(MAX) | -0.3 | V | DRV pin, continuous voltage | 5 | ||
| Maximum current for DRV pin | IDRV(MAX) | -300 | 500 | mA | 5 | ||
| Maximum voltage on low power pins | VMAX | -0.3 | 5.5 | V | Except DRV and VCC pins | 5 | |
| Current range for low power pins | IMAX | -2 | 5 | mA | Except DRV and VCC pins | 5 | |
| Maximum junction temperature | TJ(MAX) | 150 | °C | 5 | |||
| Storage temperature range | -60 | 150 | °C | 5 | |||
| Operating temperature range | -40 | 125 | °C | 5 | |||
| VCC operating range after start-up | 9.4 | 26 | V | After start-up (VCC(OVP) minimum level) | 3 | ||
| Startup threshold VCC(on) | VCC(on) | 16 | 18 | 20 | V | VCC rising | 5 |
| Minimum operating voltage VCC(off) | VCC(off) | 8.2 | 8.8 | 9.4 | V | VCC falling | 5 |
| Hysteresis VCC(on) - VCC(off) | VCC(HYS) | 8 | V | 5 | |||
| Internal logic reset VCC(reset) | VCC(reset) | 4 | 5 | 6 | V | Internal logic reset | 5 |
| VCC Over Voltage Protection threshold | VCC(OVP) | 25.5 | 26.8 | 28.5 | V | 5 | |
| Startup current | ICC(start) | 13 | 30 | A | 5 | ||
| Startup current in fault mode | ICC(Fault) | 58 | 75 | A | 5 | ||
| Supply current device disabled/fault | ICC1 | 0.8 | 1 | 1.2 | mA | VCC > VCC(off) | 5 |
| Supply current device enabled/no output load | ICC2 | 2.6 | 4 | mA | Fsw = 65 kHz | 5 | |
| Supply current device switching | ICC3 | 3 | 4.5 | mA | CDRV = 470 pF, Fsw = 65 kHz | 5 | |
| Maximum internal current limit | VILIM | 0.95 | 1 | 1.05 | V | 5 | |
| Leading edge blanking duration for VILIM | tLEB | 240 | 300 | 360 | ns | 5 | |
| Propagation delay from current detection to gate off-state | tILIM | 100 | 150 | ns | 5 | ||
| Maximum on-time | ton(MAX) | 26 | 36 | 46 | s | 6 | |
| Threshold for immediate fault protection activation | VCS(stop) | 1.35 | 1.5 | 1.65 | V | 6 | |
| Current source for CS to GND short detection | ICS(short) | 400 | 500 | 600 | A | 6 | |
| Current sense threshold for CS to GND short detection | VCS(low) | 30 | 65 | 100 | mV | VCS rising | 6 |
| DRV low voltage | VDRV(low) | 8 | V | VCC = VCC(off)+0.2 V, CDRV = 470 pF, RDRV = 33 k | 6 | ||
| DRV high voltage | VDRV(high) | 10 | 12 | 14 | V | VCC = VCC(MAX), CDRV = 470 pF, RDRV = 33 k | 6 |
| Upper ZCD threshold voltage | VZCD(rising) | 90 | 150 | mV | VZCD rising | 6 | |
| Lower ZCD threshold voltage | VZCD(falling) | 35 | 55 | mV | VZCD falling | 6 | |
| ZCD hysteresis | VZCD(HYS) | 15 | mV | 6 | |||
| Propagation delay from valley detection to DRV high | TDEM | 100 | 300 | ns | VZCD falling | 6 | |
| Blanking delay after on-time | TZCD(blank1) | 1.12 | 1.5 | 1.88 | s | VREFX > 30% VREF | 6 |
| Blanking delay at light load | TZCD(blank2) | 0.56 | 0.75 | 0.94 | s | VREFX < 25% VREF | 6 |
| Timeout after last DEMAG transition | TTIMO | 5 | 6.5 | 8 | s | 6 | |
| Reference voltage at TJ = 25°C (A and B versions) | VREF | 245 | 250 | 255 | mV | TJ = 25°C, A and B versions | 6 |
| Reference voltage TJ = 25°C to 100°C (A and B versions) | VREF | 242.5 | 250 | 257.5 | mV | TJ = 25°C to 100°C, A and B versions | 6 |
| Reference voltage TJ = −40°C to 125°C (A and B versions) | VREF | 240 | 250 | 260 | mV | TJ = −40°C to 125°C, A and B versions | 6 |
| Error amplifier gain | GEA | 40 | 50 | 60 | S | VREFX = VREF | 6 |
| Error amplifier current capability | IEA | -60 | 60 | A | VREFX = VREF (no dimming) | 7 | |
| VVS to ICS(offset) conversion ratio | KLFF | 18 | 20 | 22 | S | 7 | |
| Line feed-forward current on CS pin | IFF | 35 | 40 | 45 | A | DRV high, VVS = 2 V | 7 |
| Offset current maximum value | Ioffset(MAX) | 80 | 100 | 120 | A | 7 | |
| Threshold for high-line range detection | VHL | 2.28 | 2.4 | 2.52 | V | VVS rising | 7 |
| Threshold for low-line range detection | VLL | 2.18 | 2.3 | 2.42 | V | VVS falling | 7 |
| Thermal shutdown | TSHDN | 130 | 150 | 170 | °C | FSW = 65 kHz | 7 |
| SD pin clamped voltage SD pin open | VSD(clamp) | 1.13 | 1.35 | 1.57 | V | SD pin open | 7 |
| SD pin detection level for OVP | VOVP | 2.35 | 2.5 | 2.65 | V | VSD rising | 7 |
| Delay before OVP or OTP confirmation | TSD(delay) | 22.5 | 30 | 37.5 | s | 7 | |
| Reference current for direct connection of an NTC | IOTP(REF) | 80 | 85 | 90 | A | 7 | |
| Fault detection level for OTP | VOTP(off) | 0.47 | 0.5 | 0.53 | V | VSD falling | 7 |
| SD pin level for operation recovery after OTP | VOTP(on) | 0.66 | 0.7 | 0.74 | V | VSD rising | 7 |
| SD pin voltage where thermal fold-back starts | VTF(start) | 0.94 | 1 | 1.06 | V | VREF is decreased | 7 |
| SD pin voltage at which thermal fold-back stops | VTF(stop) | 0.64 | 0.69 | 0.74 | V | VREF is clamped to VREF50 | 7 |
| Brown-Out ON level | VBO(on) | 0.95 | 1 | 1.05 | V | VS rising | 8 |
| Brown-Out OFF level | VBO(off) | 0.85 | 0.9 | 0.95 | V | VS falling | 8 |
| DIM pin voltage for zero output current | VDIM0 | 0.66 | 0.7 | 0.74 | V | VDIM falling | 8 |
| DIM pin voltage for maximum output current | VDIM100 | 2.32 | 2.45 | 2.6 | V | TJ = −40°C to +125°C, VDIM rising | 8 |
| DIM pin voltage for 50% output current | VDIM50 | 1.35 | 1.57 | 1.75 | V | VDIM rising or falling | 8 |
| Thermal resistance junction-to-air | RθJ-A | 180 | °C/W | 5 |
CAD (KiCad official)
- Symbol:
NCL30186BDR2G - Footprint:
Package_SO:SOIC-10_3.9x4.9mm_P1mm - 3D model: SOP-10 (KiCad packages3D, STEP)
- 3D model files:
ncl30186bdr2g-etched.step/ncl30186bdr2g-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ncl30186bdr2g.step/ncl30186bdr2g.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: onsemi datasheet (29 pp, sha256
f2992f1a48dda216, retrieved 2026-10-28, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).