main
Ray Publish 0.1.0 42605a9

NCD57090BDWR2G

onsemi · Gate Drive ICs · SOIC-8-300mil

NCD57090BDWR2G from onsemi, in a SOIC-8-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VDD1 power_in Input-side power supply that needs a good-quality bypass capacitor to GND1 placed close to the pin, and the UVLO1 circuit enables operation only when a typical supply above VUVLO1-OUT-ON (3.1 V max) is present.
2 IN+ input Non-inverting gate driver input, internally clamped to GND1 with an equivalent 125 kΩ pull-down, and a minimum pulse width is required before OUT responds.
3 IN− input Inverting gate driver input, internally clamped to VDD1 with an equivalent 50 kΩ pull-up, and a minimum pulse width is required before OUT responds.
4 GND1 power_in Input-side ground reference.
5 VDD2 power_in Output-side positive power supply with an operating range from UVLO2 to 30 V, requiring a good-quality bypass capacitor to GND2 placed close to the pin.
6 OUT output Driver output that provides the drive voltage and source/sink current to the IGBT/MOSFET gate, and is actively pulled low during start-up.
7 GND2 power_in Output-side gate drive reference connecting to the IGBT emitter or MOSFET source (pin 7 for the NCD57090B variant).
8 VEE2 power_in Output-side negative power supply (NCD57090B) with an operating range of −15 V to 0 V relative to GND2, requiring a bypass capacitor to GND2; typical bipolar operation uses −5 V.

Key specifications

Parameter Value
Manufacturer onsemi
Package SOIC-8-300mil
Category Power Supply Chip
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply Voltage, Input Side VDD1−GND1 -0.3 22 V 7
Positive Power Supply, Output Side VDD2−GND2 -0.3 32 V 7
Negative Power Supply, Output Side VEE2−GND2 -18 0.3 V 7
Differential Power Supply, Output Side VDD2−VEE2 (VMAX2) 0 36 V NCD57090B 7
Gate-driver Output Low Voltage VOUT−GND2 / VOUTL−GND2 -0.3 V NCD57090A/B/D/F 7
Gate-driver Output Sourcing Current IPK−SRC 6.5 A maximum pulse width = 10 s, maximum duty cycle = 0.2%, VDD2 = 15 V, VEE2 = 0 V 7
Gate-driver Output Sinking Current IPK−SNK 6.5 A maximum pulse width = 10 s, maximum duty cycle = 0.2%, VDD2 = 15 V, VEE2 = 0 V 7
Clamp Sinking Current IPK−CLAMP 2.5 A maximum pulse width = 10 s, maximum duty cycle = 0.2%, VCLAMP = 2.5 V 7
Maximum Short Circuit Clamping Time tCLP 10 s IOUT_CLAMP = 500 mA 7
Voltage at IN+, IN− VLIM−GND1 -0.3 V 7
Clamp Voltage VCLAMP−GND2 -0.3 V 7
Power Dissipation (SOIC−8 Wide Package) PD 1470 mW 7
Maximum Junction Temperature TJ(max) -40 150 °C 8
Storage Temperature Range TSTG -65 150 °C 8
ESD Capability, Human Body Model ESDHBM -2 2 kV Note 2: HBM per AEC−Q100−002 8
Thermal Resistance, Junction−to−Air, 1-layer RJA 156 °C/W 1-layer; Note 5 (100 mm2 copper, 1 oz, FR4) 8
Thermal Resistance, Junction−to−Air, 4-layer RJA 85 °C/W 4-layer; Note 5 (100 mm2 copper, 1 oz, FR4) 8
Supply Voltage, Input Side VDD1−GND1 20 V 8
Positive Power Supply, Output Side VDD2−GND2 30 V 8
Negative Power Supply, Output Side VEE2−GND2 -15 0 V NCD57090B 8
Differential Power Supply, Output Side VDD2−VEE2 (VMAX2) 0 32 V NCD57090B 8
Low Level Input Voltage at IN+, IN− VIL 0 V Note 7 (valid for 3.3 V and 5 V VDD1) 8
Common Mode Transient Immunity /dVISO/dt/ 100 kV/s Note 8: ±1500 V pulses 8
Ambient Temperature TA -40 125 °C 8
UVLO1 Output Enabled VUVLO1−OUT−ON 3.1 V 9
UVLO1 Output Disabled VUVLO1−OUT−OFF 2.4 V 9
UVLO1 Hysteresis VUVLO1−HYST 0.1 V 9
UVLO2 Output Enabled VUVLO2−OUT−ON 12.4 12.9 13.4 V NCx57090y 9
UVLO2 Output Disabled VUVLO2−OUT−OFF 11.5 12 12.5 V NCx57090y 9
UVLO2 Hysteresis VUVLO2−HYST 0.7 1 V 9
Input Supply Quiescent Current IDD1−0−3.3 2 mA IN+ = Low, IN− = Low, VDD1 = 3.3 V 9
Input Supply Current IDD1−100−5 5.5 mA IN+ = High, IN− = Low 9
Output Positive Supply Quiescent Current IDD2−0 2 mA IN+ = Low, IN− = Low, no load 9
Output Positive Supply Current IDD2−100 2 mA IN+ = High, IN− = Low, no load 9
Output Negative Supply Quiescent Current (NCD57090B) IEE2−0 2 mA IN+ = Low, IN− = Low, no load, VEE2 = −8 V 9
Output Negative Supply Current (NCD57090B) IEE2−100 2 mA IN+ = High, IN− = Low, no load, VEE2 = −8 V 9
IN− Input Current IIN−L−3.3 100 A VIN− = 0 V, VDD1 = 3.3 V 9
IN+ Input Current IIN+H−3.3 100 A VIN+ = VDD1 = 3.3 V 9
Input Pulse Width for Guaranteed No Response at Output tON−MIN1 10 ns 9
Input Pulse Width for Guaranteed Response at Output tON−MIN2 40 ns 9
Output Low State VOUTL1 0.15 0.3 V ISINK = 200 mA 10
Output Low State VOUTL2 0.8 V ISINK = 1.0 A, TA = 25°C 10
Output High State VOUTH1 0.2 0.35 V ISRC = 200 mA 10
Output High State VOUTH2 1 V ISRC = 1.0 A, TA = 25°C 10
Clamping Voltage, Sourcing (VOUT / VOUTH − VDD2) VCLAMP−OUTH 0.7 0.9 V IN+ = Low, IN− = High, ICLAMP−OUT/OUTH = 500 mA, pulse test, tCLPmax = 10 s 10
Clamping Voltage, Sinking (VOUTL − VDD2) VCLAMP−OUTL 0.8 1.5 V IN+ = High, IN− = Low, ICLAMP−OUTL = 500 mA, pulse test, tCLPmax = 10 s 10
IN+, IN− to Output High Propagation Delay tPD−ON−3.3 40 60 90 ns VDD1 = VIN+ = 3.3 V, VIN− = 0 V; CLOAD = 10 nF, VIH to 10% of output change, pulse width > 150 ns 10
IN+, IN− to Output Low Propagation Delay tPD−OFF−3.3 40 60 90 ns VDD1 = VIN+ = 3.3 V, VIN− = 0 V; CLOAD = 10 nF, VIH to 10% of output change, pulse width > 150 ns 10
Propagation Delay Distortion (= tPD−ON − tPD−OFF) tDISTORT -25 25 ns TA = −40°C to 125°C, PW > 150 ns 10
Prop Delay Distortion between Parts tDISTORT_TOT -30 0 30 ns PW > 150 ns 10

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
housing ABS RIO Insulation Resistance at TS, VIO = 500 V 109 Table 3. ABSOLUTE MAXIMUM RATINGS (Note 1) 7

CAD (KiCad official)

  • Symbol: NCD57090BDWR2G
  • Footprint: Package_SO:SOIC-8_7.5x5.85mm_P1.27mm
  • 3D model: SOIC-8-300mil (KiCad packages3D, STEP)
  • 3D model files: ncd57090bdwr2g-etched.step / ncd57090bdwr2g-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ncd57090bdwr2g.step / ncd57090bdwr2g.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: onsemi datasheet (26 pp, sha256 26abe74476d9160c, retrieved 2026-11-11, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF