3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownN32WB452CEQ6
Nations Technologies Inc · Other Processors and Microcontrollers (MCUs) · QFN-48-EP(6x6)
N32WB452CEQ6 from Nations Technologies Inc, in a QFN-48-EP(6x6). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VBAT | power_in | Backup-domain supply, 1.8 V to 3.6 V, powers the RTC, the 32 kHz oscillator and the backup registers when VDD is off. |
| 2 | PC13-TAMPER-RTC | bidirectional | Backup-domain I/O (TC) that defaults to PC13 and TAMPER-RTC; as an output it is limited to 2 MHz, a 30 pF load and cannot source current for LEDs because the backup supply switch is limited to 3 mA. |
| 3 | PC14-OSC32_IN | bidirectional | Backup-domain I/O (TC) that defaults to PC14 and serves as the OSC32_IN input of the 32.768 kHz LSE crystal; the same 3 mA backup-switch output limits apply (2 MHz, 30 pF, no LED drive). |
| 4 | PC15-OSC32_OUT | bidirectional | Backup-domain I/O (TC) that defaults to PC15 and serves as the OSC32_OUT output of the 32.768 kHz LSE crystal; the same 3 mA backup-switch output limits apply (2 MHz, 30 pF, no LED drive). |
| 5 | OSC_IN | input | HSE oscillator input for a 4 MHz to 32 MHz crystal or resonator, and this pin resets to OSC_IN and can be remapped by software to PD0 (note 7). |
| 6 | OSC_OUT | output | HSE oscillator output for a 4 MHz to 32 MHz crystal or resonator, and this pin resets to OSC_OUT and can be remapped by software to PD1 (note 7). |
| 7 | NRST | bidirectional | Active-low reset pin with an internal pull-up of about 40 kΩ (20 kΩ to 50 kΩ), where VIL is at most 0.8 V and input pulses shorter than 100 ns are filtered. |
| 8 | VSSA | power_in | Analog ground for the ADC, DAC, RC oscillators and PLL, which must be connected to VSS. |
| 9 | VDDA | power_in | Analog supply, 1.8 V to 3.6 V, for the ADC, DAC, RC oscillators and PLL, which must be connected to VDD (at most 300 mV difference). |
| 10 | PA0-WKUP | bidirectional | TTa-level GPIO (not 5 V tolerant) that also serves as the WKUP pin, where a rising edge wakes the device from STANDBY, and as ADC1_IN1. |
| 11 | PA4 | bidirectional | TTa-level GPIO that defaults to PA4 and also provides DAC_OUT1 and ADC2_IN1, with alternates SPI1_NSS, USART2_CK, DVP_D0, TSC_CHN0 and I2C2_SCL. |
| 12 | PA5 | bidirectional | TTa-level GPIO that defaults to PA5 and also provides DAC_OUT2 and ADC2_IN2, with alternates SPI1_SCK, DVP_D1, TSC_CHN1 and I2C2_SDA. |
| 13 | PA6 | bidirectional | TTa-level GPIO that defaults to PA6 and also provides ADC1_IN3, with alternates SPI1_MISO, TIM8_BKIN, TIM3_CH1, DVP_D2 and TIM1_BKIN. |
| 14 | PA7 | bidirectional | TTa-level GPIO that defaults to PA7 and also provides ADC2_IN4, with alternates SPI1_MOSI, TIM8_CH1N, TIM3_CH2, DVP_D3 and TIM1_CH1N. |
| 15 | PB2/BOOT1 | bidirectional | TTa-level GPIO that defaults to PB2/BOOT1, where BOOT1 is an input with pull-down used with BOOT0 to select the startup mode, and it also provides ADC2_IN13, with alternates DVP_D3, UART4_TX and SPI1_NSS. |
| 16 | PB10 | bidirectional | TTa-level GPIO that defaults to PB10 with alternates I2C2_SCL, USART3_TX, TIM2_CH3, XFMC_D11 and DVP_D4. |
| 17 | PB11 | bidirectional | TTa-level GPIO that defaults to PB11 with alternates I2C2_SDA, USART3_RX, TIM2_CH4, XFMC_D12 and DVP_D5. |
| 18 | VSS_1 | power_in | Ground pin for the digital I/O and core domain. |
| 19 | VDD_1 | power_in | Supply pin, 1.8 V to 3.6 V, for the I/O pins and the internal regulator. |
| 20 | PB12 | bidirectional | TTa-level GPIO that defaults to PB12 with alternates SPI2_NSS, I2S2_WS, I2C2_SMBA, USART3_CK, TIM1_BKIN and CAN2_RX. |
| 21 | BLE_SWITCH | passive | BLE pin shown in the BLE DCDC-mode reference circuit (Figure 3-4), with no further electrical limits given in the text. |
| 22 | PB13 | bidirectional | TTa-level GPIO that defaults to PB13 with alternates SPI2_SCK, I2S2_CK, USART3_CTS, TIM1_CH1N, CAN2_TX and UART5_TX. |
| 23 | PB14 | bidirectional | TTa-level GPIO that defaults to PB14 with alternates SPI2_MISO, TIM1_CH2N, USART3_RTS, TSC_CHN2 and UART5_RX. |
| 24 | PB15 | bidirectional | TTa-level GPIO that defaults to PB15 with alternates SPI2_MOSI, I2S2_SD, TIM1_CH3N and TSC_CHN3. |
| 25 | BLE_VDCDC | passive | BLE DC-DC output node that connects to an external inductor (1.5 µH to 3 µH, 2.2 µH typical) and output capacitor (0.8 µF to 5 µF) in DCDC mode. |
| 26 | BLE_VCC | power_in | Supply for the BLE RF circuit, 1.8 V to 3.6 V. |
| 27 | PA8 | bidirectional | 5 V tolerant (FT) GPIO that defaults to PA8 with alternates USART1_CK, TIM1_CH1 and MCO. |
| 28 | PA9 | bidirectional | 5 V tolerant (FT) GPIO that defaults to PA9 with alternates USART1_TX, TIM1_CH2, TSC_DOUT and I2C4_SCL. |
| 29 | PA11 | bidirectional | 5 V tolerant (FT) GPIO that defaults to PA11 with alternates USART1_CTS, USBDM, CAN1_RX and TIM1_CH4. |
| 30 | PA12 | bidirectional | 5 V tolerant (FT) GPIO that defaults to PA12 with alternates USART1_RTS, USBDP, CAN1_TX and TIM1_ETR. |
| 31 | BLE_RFIOP | passive | BLE RF I/O pin that connects to the external antenna. |
| 32 | BLE_VDCDCCRF | passive | BLE DC-DC-related pin shown in the BLE reference circuits (Figure 3-4), with no further function or limit stated in the text. |
| 33 | PA13 | bidirectional | 5 V tolerant (FT) GPIO that defaults to the JTMS/SWDIO debug function, with alternate UART4_TX. |
| 34 | VSS_2 | power_in | Ground pin for the digital I/O and core domain. |
| 35 | VDD_2 | power_in | Supply pin, 1.8 V to 3.6 V, for the I/O pins and the internal regulator. |
| 36 | PA14 | bidirectional | 5 V tolerant (FT) GPIO that defaults to the JTCK/SWCLK debug function, with alternate UART4_RX. |
| 37 | PA15 | bidirectional | 5 V tolerant (FT) GPIO that defaults to the JTDI debug function, with alternates SPI1_NSS, USART2_CTS, TIM8_CH1N, SPI3_NSS, I2S3_WS and TIM2_CH1_ETR. |
| 38 | PB3 | bidirectional | 5 V tolerant (FT) GPIO that defaults to the JTDO function, with alternates TRACESWO, TIM2_CH2, SPI1_SCK, USART2_RTS, TIM8_BKIN and SPI3_SCK. |
| 39 | PB4 | bidirectional | 5 V tolerant (FT) GPIO that defaults to the NJTRST function, with alternates TIM3_CH1, SPI1_MISO, USART2_TX, TIM8_ETR and SPI3_MISO. |
| 40 | PB5 | bidirectional | 5 V tolerant (FT) GPIO that defaults to PB5 with alternates I2C1_SMBA, SPI3_MOSI, I2S3_SD, TIM3_CH2, SPI1_MOSI, CAN2_RX, USART2_RX and TIM1_BKIN. |
| 41 | BLE_DVDD | power_in | Supply for the BLE control module and internal regulator, 1.8 V to 3.6 V, with an external capacitor. |
| 42 | BLE_XO32MM | passive | BLE 32 MHz crystal oscillator terminal (XO32M negative side) for the external 32 MHz crystal. |
| 43 | BLE_XO32MP | passive | BLE 32 MHz crystal oscillator terminal (XO32M positive side) for the external 32 MHz crystal. |
| 44 | PB6 | bidirectional | TTa-level GPIO that defaults to PB6 with alternates I2C1_SCL, TIM4_CH1, TSC_CHN20, USART1_TX, CAN2_TX, XFMC_NE2 and XFMC_NCE3. |
| 45 | PB7 | bidirectional | TTa-level GPIO that defaults to PB7 with alternates I2C1_SDA, XFMC_NADV, TIM4_CH2, TSC_CHN21 and USART1_RX. |
| 46 | BOOT0 | input | Boot-mode select input with an internal pull-down that, together with BOOT1, selects flash, system memory or internal SRAM boot at startup. |
| 47 | VSS_3 | power_in | Ground pin for the digital I/O and core domain. |
| 48 | VDD_3 | power_in | Supply pin, 1.8 V to 3.6 V, for the I/O pins and the internal regulator (pin position taken from Figure 3-1 only). |
| 49 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Nations Technologies Inc |
| Package | QFN-48-EP(6x6) |
| Category | Embedded Processors & Controllers |
| Pins | 49 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VDD-VSS external main supply voltage (includes VDDA and VDD) | VDD-VSS | -0.3 | 4 | V | 包含VDDA和VDD | 48 | |
| Input voltage on 5V-tolerant pins | VIN | 5.5 | V | 5V容忍的引脚 | 48 | ||
| Voltage difference between supply pins | /ΔVDDx/ | 50 | mV | 不同供电引脚之间 | 48 | ||
| Voltage difference between ground pins | /VSSx-VSS/ | 50 | mV | 不同接地引脚之间 | 48 | ||
| Total current through VDD/VDDA supply line | IVDD | 150 | mA | 48 | |||
| Total current through VSS ground line | IVSS | 150 | mA | 48 | |||
| Output sink current on any I/O and control pin | IIO | 12 | mA | 任意I/O和控制引脚上的输出灌电流 | 48 | ||
| Output current on any I/O and control pin | IIO | -12 | mA | 任意I/O和控制引脚上的输出电流 | 48 | ||
| Injection current on NRST pin | IINJ(PIN) | -5 | 5 | mA | NRST引脚的注入电流 | 48 | |
| Injection current on HSE OSC_IN and LSE OSC_IN pins | IINJ(PIN) | -5 | 5 | mA | HSE的OSC_IN引脚和LSE的OSC_IN引脚的注入电流 | 48 | |
| Injection current on other pins | IINJ(PIN) | -5 | 5 | mA | 其他引脚的注入电流 | 48 | |
| Storage temperature range | TSTG | -60 | 150 | ℃ | 49 | ||
| Maximum junction temperature | TJ | 150 | ℃ | 49 | |||
| Normal operating supply voltage (Bluetooth) | VCC(op) | 1.8 | 3 | 3.6 | V | 正常工作电源电压 | 49 |
| Internal memory operating voltage (Bluetooth) | VCC(sto) | -0.3 | 3.6 | V | 内部存储器工作电压 | 49 | |
| RF input signal amplitude | 10 | dBm | RF输入信号的幅度 | 49 | |||
| DCDC external inductance | 1.5 | 2.2 | 3 | uH | DCDC外部电感 | 49 | |
| DCDC load capacitance | COUT | 0.8 | 1 | 5 | uF | DCDC负载电容 | 49 |
| Receiver saturation level (1-Mbps GFSK BLE RX) | 10 | dBm | 误码率=1‰ | 50 | |||
| Single-ended output power into 50 ohm load (1-Mbps GFSK BLE TX) | Pout | -20 | 0 | 3 | dBm | 单端发射功率(接50ohm负载) | 50 |
| Normal operating HCLK (AHB) frequency | fHCLK | 0 | 144 | MHz | 50 | ||
| APB1 clock frequency | fPCLK1 | 0 | 36 | MHz | 50 | ||
| APB2 clock frequency | fPCLK2 | 0 | 72 | MHz | 50 | ||
| Standard operating voltage | VDD | 1.8 | 3.6 | V | 50 | ||
| Analog operating voltage | VDDA | 1.8 | 3.6 | V | 必须与VDD相同 | 50 | |
| Backup domain operating voltage | VBAT | 1.8 | 3.6 | V | 50 | ||
| Ambient temperature (max power consumption) | TA | -40 | 85 | ℃ | 温度标号7; 最大功率消耗 | 50 | |
| Ambient temperature (low power consumption) | TA | -40 | 105 | ℃ | 温度标号7; 低功率消耗 | 50 | |
| Junction temperature range | TJ | -40 | 105 | ℃ | 温度标号7 | 50 | |
| Supply voltage for USB operation | VDD | 3 | 3.6 | V | USB操作电压 | 77 | |
| Common-mode range for USB differential input | VCM | 0.8 | 2.5 | V | 包含VDI范围 | 77 | |
| Single-ended receiver threshold (USB) | VSE | 1.3 | 2 | 77 | |||
| Static output low level (USB) | VOL | 0.3 | V | 1.5kΩ的RL接至3.6V | 78 | ||
| Static output high level (USB) | VOH | 2.8 | 3.6 | V | 15kΩ的RL接至VSS | 78 | |
| USB rise time | tr | 4 | 20 | ns | CL ≤ 50pF | 78 | |
| USB fall time | tf | 4 | 20 | ns | CL ≤ 50pF | 78 | |
| USB rise/fall time matching | trfm | 90 | 110 | % | tr / tf | 78 | |
| USB output signal crossover voltage | VCRS | 1.3 | 2 | V | 78 | ||
| USB output series matching resistor | Rs | 27 | 39 | Ohm | 需匹配电阻外置,靠近芯片引脚 | 78 | |
| ADC supply voltage | VDDA | 1.8 | 3.6 | V | 78 | ||
| ADC clock frequency | fADC | 72 | MHz | 78 | |||
| ADC sampling rate | fs | 5 | MHz | 78 | |||
| ADC sampling time | tS | 1.5 | 239.5 | 1/fADC | 79 | ||
| ADC power-up time | tSTAB | 0 | 0 | 20 | μs | 79 | |
| ADC total conversion time (including sampling) | tCONV | 14 | 252 | 1/fADC | 包括采样时间 | 79 | |
| ADC integral error ET (total unadjusted error) | ET | -5 | 1.3 | 5 | LSB | fHCLK=72MHz, fADC=72MHz, 1.75Msps, VDDA=3.3V, TA=25°C, VREF+=VDDA, after calibration | 79 |
| ADC offset error EO | EO | -2 | 1 | 2 | LSB | fHCLK=72MHz, fADC=72MHz, 1.75Msps, VDDA=3.3V, TA=25°C, VREF+=VDDA, after calibration | 79 |
| ADC differential linearity error ED | ED | -1 | 0.7 | 1 | LSB | fHCLK=72MHz, fADC=72MHz, 1.75Msps, VDDA=3.3V, TA=25°C, VREF+=VDDA, after calibration | 79 |
| ADC integral linearity error EL | EL | -2 | 0.8 | 2 | LSB | fHCLK=72MHz, fADC=72MHz, 1.75Msps, VDDA=3.3V, TA=25°C, VREF+=VDDA, after calibration | 79 |
| SD/MMC clock frequency in data transfer mode | fPP | 0 | 48 | MHz | CL ≤ 30pF | 77 | |
| Clock low time | tW(CKL) | 32 | ns | fPP = 16 MHz, CL ≤ 30pF | 77 | ||
| Clock high time | tW(CKH) | 30 | ns | CL ≤ 30pF | 77 | ||
| Clock rise time | tr | 6 | ns | CL ≤ 30pF | 77 | ||
| Clock fall time | tf | 6 | ns | CL ≤ 30pF | 77 | ||
| CMD, D input setup time (referenced to CK) | tISU | 2 | ns | CL ≤ 30pF | 77 | ||
| CMD, D input hold time (referenced to CK) | tIH | 2 | ns | CL ≤ 30pF | 77 | ||
| CMD, D output valid time, MMC and SD high-speed mode (referenced to CK) | tOV | 14 | ns | CL ≤ 30pF | 77 | ||
| CMD, D output hold time, MMC and SD high-speed mode (referenced to CK) | tOH | 2.5 | ns | CL ≤ 30pF | 77 | ||
| CMD, D output valid default time, SD default mode (referenced to CK) | tOVD | 9 | ns | CL ≤ 30pF | 77 | ||
| CMD, D output hold default time, SD default mode (referenced to CK) | tOHD | -2 | ns | CL ≤ 30pF | 77 |
CAD (KiCad official)
- Symbol:
N32WB452CEQ6 - Footprint:
Package_DFN_QFN:QFN-48-1EP_6x6mm_P0.4mm_EP4.2x4.2mm - 3D model: QFN-48-EP(6x6), generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 0.9 mm nominal QFN height). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions are nominal, not the manufacturer's CAD (STEP)
- 3D model files:
n32wb452ceq6-etched.step/n32wb452ceq6-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);n32wb452ceq6.step/n32wb452ceq6.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Nations Technologies Inc datasheet (88 pp, sha256
082b04b4fedea011, retrieved 2026-11-05, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).