main
Ray
Publish 0.1.0
595b793
N32G457VEL7
Nations Technologies Inc · Microcontroller Units (MCUs/MPUs/SOCs) · LQFP-100(14x14)
N32G457VEL7 from Nations Technologies Inc, in a LQFP-100(14x14). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | PE2 | bidirectional | 5V tolerant GPIO with default function PE2; alternates include TRACECK, UART6_TX and DVP_HSYNC. |
| 2 | PE3 | bidirectional | 5V tolerant GPIO with default function PE3; alternates include TRACED0, UART6_RX and DVP_VSYNC. |
| 3 | PE4 | bidirectional | 5V tolerant GPIO with default function PE4; alternates include TRACED1 and DVP_PCLK. |
| 4 | PE5 | bidirectional | 5V tolerant GPIO with default function PE5; alternates include TRACED2 and DVP_D0. |
| 5 | PE6 | bidirectional | 5V tolerant GPIO with default function PE6; alternates include TRACED3 and DVP_D1. |
| 6 | VBAT | power_in | Backup supply 1.8~3.6V that powers the RTC, the external 32kHz oscillator and backup registers when VDD is off. |
| 7 | PC13-TAMPER-RTC | bidirectional | Standard 3.3V I/O powered through a switch limited to 3mA; as output it is limited to 2MHz mode, 30pF maximum load and no current sourcing. |
| 8 | PC14-OSC32_IN | bidirectional | Standard 3.3V I/O powered through a switch limited to 3mA; as output it is limited to 2MHz mode and 30pF maximum load. |
| 9 | PC15-OSC32_OUT | bidirectional | Standard 3.3V I/O powered through a switch limited to 3mA; as output it is limited to 2MHz mode and 30pF maximum load. |
| 10 | VSS_5 | power_in | Ground pin; all voltages are referenced to VSS. |
| 11 | VDD_5 | power_in | Digital supply pin; VDD 1.8~3.6V powers the I/O pins and internal regulator. |
| 12 | OSC_IN | input | HSE oscillator input for a 4~32MHz crystal or resonator or an external clock, with high level 0.8VDD to VDD. |
| 13 | OSC_OUT | output | HSE oscillator output for the 4~32MHz crystal or resonator. |
| 14 | NRST | bidirectional | Active-low external reset pin with internal pull-up resistor of 30~70kOhm. |
| 15 | PC0 | bidirectional | 3.3V tolerant I/O with analog function; alternates include ADC12_IN6, I2C3_SCL, COMP7_INM, DVP_D2 and UART6_TX. |
| 16 | PC1 | bidirectional | 3.3V tolerant I/O with analog function; alternates include ADC12_IN7, ETH_MII_MDC, ETH_RMII_MDC, I2C3_SDA, COMP7_INP and UART6_RX. |
| 17 | PC2 | bidirectional | 3.3V tolerant I/O with analog function; alternates include ADC12_IN8, ETH_MII_TXD2, COMP7_OUT, UART7_TX, SPI3_NSS and I2S3_WS. |
| 18 | PC3 | bidirectional | 3.3V tolerant I/O with analog function; alternates include ADC12_IN9, ETH_MII_TX_CLK, UART7_RX, SPI3_SCK, I2S3_CK, OPAMP3_VINP, OPAMP4_VINP and COMP5_INP. |
| 19 | VSSA | power_in | Analog ground for ADC, DAC, OPAMP, COMP and TSC; must be connected to VSS. |
| 20 | VREF- | power_in | Negative ADC reference voltage; ADC input range is VREF- to VREF+. |
| 21 | VREF+ | power_in | Positive reference voltage for the ADC and DAC; it must always be below VDDA for the DAC. |
| 22 | VDDA | power_in | Analog supply 1.8~3.6V for ADC, DAC, OPAMP, COMP and TSC; must be the same as VDD. |
| 23 | PA0-WKUP | bidirectional | 3.3V tolerant I/O with analog function and WKUP wake-up input; alternates include ADC1_IN1, TIM2_CH1_ETR, USART2_CTS and COMP1_INM. |
| 24 | PA1 | bidirectional | 3.3V tolerant I/O with analog function; alternates include ADC1_IN2, USART2_RTS, TIM5_CH2, ETH_RMII_REF_CLK, DVP_HSYNC, COMP1_INP and OPAMP1_VINP. |
| 25 | PA2 | bidirectional | 3.3V tolerant I/O with analog function; alternates include ADC12_IN11, USART2_TX, TIM5_CH3, ETH_RMII_MDIO, DVP_VSYNC, OPAMP1_INM and COMP3_OUT. |
| 26 | PA3 | bidirectional | 3.3V tolerant I/O with analog function; alternates include ADC1_IN4, USART2_RX, TIM5_CH4, ETH_MII_COL, DVP_PCLK, OPAMP1_VINM, OPAMP1_VINP and COMP5_INP. |
| 27 | VSS_4 | power_in | Ground pin; all voltages are referenced to VSS. |
| 28 | VDD_4 | power_in | Digital supply pin; VDD 1.8~3.6V powers the I/O pins and internal regulator. |
| 29 | PA4 | bidirectional | 3.3V tolerant I/O with analog function; alternates include SPI1_NSS, USART2_CK, DAC_OUT1, ADC2_IN1, DVP_D0, QSPI_NSS, TSC_CHN0 and I2C2_SCL. |
| 30 | PA5 | bidirectional | 3.3V tolerant I/O with analog function; alternates include SPI1_SCK, DAC_OUT2, ADC2_IN2, DVP_D1, QSPI_SCK, TSC_CHN1 and I2C2_SDA. |
| 31 | PA6 | bidirectional | 3.3V tolerant I/O with analog function; alternates include SPI1_MISO, TIM8_BKIN, ADC1_IN3, TIM3_CH1, DVP_D2, QSPI_IO0, COMP2_OUT, TIM1_BKIN and OPAMP1_VOUT. |
| 32 | PA7 | bidirectional | 3.3V tolerant I/O with analog function; alternates include SPI1_MOSI, TIM8_CH1N, ADC2_IN4, TIM3_CH2, DVP_D3, ETH_RMII_CRS_DV, QSPI_IO1, TIM1_CH1N and COMP2_INP. |
| 33 | PC4 | bidirectional | 3.3V tolerant I/O with analog function; alternates include ADC2_IN5, DVP_D4, ETH_RMII_RXD0, QSPI_IO2, UART7_TX, I2C3_SCL, OPAMP3_VINM and COMP4_INM. |
| 34 | PC5 | bidirectional | 3.3V tolerant I/O with analog function; alternates include ADC2_IN12, ETH_RMII_RXD1, DVP_D5, QSPI_IO3, UART7_RX, COMP4_OUT, I2C3_SDA, OPAMP4_VINP and COMP6_INP. |
| 35 | PB0 | bidirectional | 3.3V tolerant I/O with analog function; alternates include ADC3_IN12, TIM3_CH3, TIM8_CH2N, ETH_MII_RXD2, DVP_D6, COMP5_OUT, TIM1_CH2N, UART6_TX, OPAMP2_VINP and COMP3_INP. |
| 36 | PB1 | bidirectional | 3.3V tolerant I/O with analog function; alternates include ADC2_IN3, TIM3_CH4, TIM8_CH3N, ETH_MII_RXD3, DVP_D7, TIM1_CH3N, OPAMP2_VOUT, UART6_RX, COMP2_INM and COMP1_OUT. |
| 37 | PB2-BOOT1 | bidirectional | 3.3V tolerant I/O with analog function; BOOT1 is an input with pull-down; alternates include ADC2_IN13, DVP_D3, UART4_TX and SPI1_NSS. |
| 38 | PE7 | bidirectional | 3.3V tolerant I/O with analog function; alternates include ADC3_IN13, TIM1_ETR, UART4_RX, SPI1_SCK and COMP3_INM. |
| 39 | PE8 | bidirectional | 3.3V tolerant I/O with analog function; alternates include ADC34_IN6, TIM1_CH1N, UART5_TX, SDIO_D0, SPI1_MISO, OPAMP2_INP and COMP2_INM. |
| 40 | PE9 | bidirectional | 3.3V tolerant I/O with analog function; alternates include ADC3_IN2, TIM1_CH1, UART5_RX, SDIO_D1 and SPI1_MOSI. |
| 41 | PE10 | bidirectional | 3.3V tolerant I/O with analog function; alternates include ADC3_IN14, TIM1_CH2N, SDIO_D2, SPI2_NSS and I2S2_WS. |
| 42 | PE11 | bidirectional | 3.3V tolerant I/O with analog function; alternates include ADC3_IN15, TIM1_CH2, SDIO_D3, SPI2_SCK and I2S2_CK. |
| 43 | PE12 | bidirectional | 3.3V tolerant I/O with analog function; alternates include ADC3_IN4, TIM1_CH3N, SDIO_CK and SPI2_MISO. |
| 44 | PE13 | bidirectional | 3.3V tolerant I/O with analog function; alternates include ADC3_IN3, TIM1_CH3, SPI2_MOSI, I2S2_SD and SDIO_CMD. |
| 45 | PE14 | bidirectional | 3.3V tolerant I/O with analog function; alternates include ADC4_IN1 and TIM1_CH4. |
| 46 | PE15 | bidirectional | 3.3V tolerant I/O with analog function; alternates include ADC4_IN2 and TIM1_BKIN. |
| 47 | PB10 | bidirectional | 3.3V tolerant I/O with analog function and fail-safe capability; alternates include I2C2_SCL, USART3_TX, ETH_MII_RX_ER, COMP3_OUT, TIM2_CH3, OPAMP3_VINM and DVP_D4. |
| 48 | PB11 | bidirectional | 3.3V tolerant I/O with analog function; alternates include I2C2_SDA, USART3_RX, ETH_MII_TX_EN, ADC3_IN1, TIM2_CH4, OPAMP3_VOUT, COMP2_INP, COMP5_OUT and DVP_D5. |
| 49 | VSS_1 | power_in | Ground pin; all voltages are referenced to VSS. |
| 50 | VDD_1 | power_in | Digital supply pin; VDD 1.8~3.6V powers the I/O pins and internal regulator. |
| 51 | PB12 | bidirectional | 3.3V tolerant I/O with analog function; alternates include SPI2_NSS, I2S2_WS, I2C2_SMBA, USART3_CK, TIM1_BKIN, CAN2_RX, ETH_MII_TXD0, ADC4_IN3, COMP3_INM and OPAMP4_VOUT. |
| 52 | PB13 | bidirectional | 3.3V tolerant I/O with analog function; alternates include SPI2_SCK, I2S2_CK, USART3_CTS, TIM1_CH1N, CAN2_TX, ETH_MII_TXD1, ADC3_IN5, UART5_TX and COMP4_INM. |
| 53 | PB14 | bidirectional | 3.3V tolerant I/O with analog function; alternates include SPI2_MISO, TIM1_CH2N, USART3_RTS, ADC4_IN4, TSC_CHN2, COMP3_INP and UART5_RX. |
| 54 | PB15 | bidirectional | 3.3V tolerant I/O with analog function; alternates include SPI2_MOSI, I2S2_SD, TIM1_CH3N, ADC4_IN5, TSC_CHN3 and COMP4_INP. |
| 55 | PD8 | bidirectional | 3.3V tolerant I/O with analog function; alternates include ADC4_IN12, TSC_CHN4, USART3_TX, ETH_RMII_CRS_DV, OPAMP4_VINM, SPI3_NSS, I2S3_WS, CAN1_RX and COMP6_INM. |
| 56 | PD9 | bidirectional | 3.3V tolerant I/O with analog function; alternates include ADC4_IN13, TSC_CHN5, USART3_RX, ETH_RMII_RXD0, SPI3_SCK, I2S3_CK, CAN1_TX and COMP6_INP. |
| 57 | PD10 | bidirectional | 3.3V tolerant I/O with analog function; alternates include ADC34_IN7, USART3_CK, ETH_RMII_RXD1, CAN2_RX and COMP5_INM. |
| 58 | PD11 | bidirectional | 3.3V tolerant I/O with analog function; alternates include ADC34_IN8, TSC_CHN6, USART3_CTS, ETH_MII_RXD2, CAN2_TX and SPI3_MISO. |
| 59 | PD12 | bidirectional | 3.3V tolerant I/O with analog function; alternates include ADC34_IN9, TSC_CHN7, TIM4F_CH1, USART3_RTS, ETH_MII_RXD3, SPI3_MOSI, I2S3_SD and COMP7_OUT. |
| 60 | PD13 | bidirectional | 3.3V tolerant I/O with analog function; alternates include ADC34_IN10 and TIM4F_CH2. |
| 61 | PD14 | bidirectional | 3.3V tolerant I/O with analog function; alternates include ADC34_IN11, TIM4F_CH3, I2C4_SCL and TIM8_CH1. |
| 62 | PD15 | bidirectional | 5V tolerant GPIO with fail-safe capability; alternates include TIM4F_CH4, I2C4_SDA and TIM8_CH2. |
| 63 | PC6 | bidirectional | 3.3V tolerant I/O with fail-safe capability; alternates include I2S2_MCK, TIM8_CH1, SDIO_D6, I2C4_SCL, TSC_CHN8, TIM3_CH1, SPI2_NSS, I2S2_WS and USART2_CTS. |
| 64 | PC7 | bidirectional | 3.3V tolerant I/O with fail-safe capability; alternates include I2S3_MCK, TIM8_CH2, SDIO_D7, I2C4_SDA, TSC_CHN9, TIM3_CH2, SPI2_SCK, I2S2_CK and USART2_RTS. |
| 65 | PC8 | bidirectional | 3.3V tolerant I/O with fail-safe capability; alternates include TIM8_CH3, SDIO_D0, TSC_CHN10, TIM3_CH3, SPI2_MISO and USART2_TX. |
| 66 | PC9 | bidirectional | 3.3V tolerant I/O with fail-safe capability; alternates include TIM8_CH4, SDIO_D1, TSC_CHN11, COMP6_OUT, TIM3_CH4, SPI2_MOSI, I2S2_SD, USART2_RX, OPAMP3_INP and OPAMP4_INM. |
| 67 | PA8 | bidirectional | 5V tolerant GPIO with fail-safe capability; alternates include USART1_CK, TIM1_CH1 and MCO. |
| 68 | PA9 | bidirectional | 5V tolerant GPIO with fail-safe capability; alternates include USART1_TX, TIM1_CH2, TSC_DOUT and I2C4_SCL. |
| 69 | PA10 | bidirectional | 5V tolerant GPIO with fail-safe capability; alternates include USART1_RX, TIM1_CH3 and I2C4_SDA. |
| 70 | PA11 | bidirectional | 5V tolerant GPIO with fail-safe capability; alternates include USART1_CTS, USBDM, CAN1_RX, TIM1_CH4, COMP5_OUT and COMP1_OUT. |
| 71 | PA12 | bidirectional | 5V tolerant GPIO with fail-safe capability; alternates include USART1_RTS, USBDP, CAN1_TX, TIM1_ETR, COMP6_OUT and COMP2_OUT. |
| 72 | PA13 | bidirectional | 5V tolerant GPIO with fail-safe capability; default function JTMS-SWDIO, alternate UART4_TX. |
| 73 | NC | unconnected | Listed as Not connected for the LQFP100 package in table 3-1. |
| 74 | VSS_2 | power_in | Ground pin; all voltages are referenced to VSS. |
| 75 | VDD_2 | power_in | Digital supply pin; VDD 1.8~3.6V powers the I/O pins and internal regulator. |
| 76 | PA14 | bidirectional | 5V tolerant GPIO with fail-safe capability; default function JTCK-SWCLK, alternate UART4_RX. |
| 77 | PA15 | bidirectional | 5V tolerant GPIO with fail-safe capability; default function JTDI, alternates include SPI3_NSS, I2S3_WS, TIM2_CH1_ETR, SPI1_NSS, USART2_CTS and TIM8_CH1N. |
| 78 | PC10 | bidirectional | 3.3V tolerant I/O with fail-safe capability; alternates include UART4_TX, SDIO_D2, TSC_CHN12, USART3_TX, SPI3_SCK, I2S3_CK, QSPI_NSS and COMP3_OUT. |
| 79 | PC11 | bidirectional | 3.3V tolerant I/O with fail-safe capability; alternates include UART4_RX, SDIO_D3, TSC_CHN13, USART3_RX, SPI3_MISO, QSPI_SCK and COMP4_OUT. |
| 80 | PC12 | bidirectional | 3.3V tolerant I/O with fail-safe capability; alternates include UART5_TX, SDIO_CK, TSC_CHN14, USART3_CK, SPI3_MOSI, I2S3_SD, QSPI_IO0 and TIM8_CH2N. |
| 81 | PD0 | bidirectional | 5V tolerant GPIO with fail-safe capability; PD0 is an inherent function pin on LQFP100 needing no remap; alternates include CAN1_RX, UART4_TX and QSPI_IO1. |
| 82 | PD1 | bidirectional | 5V tolerant GPIO with fail-safe capability; PD1 is an inherent function pin on LQFP100 needing no remap; alternates include CAN1_TX, UART4_RX and QSPI_IO2. |
| 83 | PD2 | bidirectional | 3.3V tolerant I/O with fail-safe capability; alternates include TIM3_ETR, UART5_RX, SDIO_CMD, TSC_CHN15, SPI3_NSS, I2S3_WS, QSPI_IO3 and TIM8_CH3N. |
| 84 | PD3 | bidirectional | 5V tolerant GPIO with fail-safe capability; alternate USART2_CTS. |
| 85 | PD4 | bidirectional | 3.3V tolerant I/O with fail-safe capability; alternates include TSC_CHN16 and USART2_RTS. |
| 86 | PD5 | bidirectional | 3.3V tolerant I/O with fail-safe capability; alternates include TSC_CHN17 and USART2_TX. |
| 87 | PD6 | bidirectional | 3.3V tolerant I/O with fail-safe capability; alternates include TSC_CHN18 and USART2_RX. |
| 88 | PD7 | bidirectional | 3.3V tolerant I/O with fail-safe capability; alternates include TSC_CHN19 and USART2_CK. |
| 89 | PB3 | bidirectional | 5V tolerant GPIO with fail-safe capability; default function JTDO, alternates include TRACESWO, TIM2_CH2, SPI1_SCK, USART2_RTS, SPI3_SCK and TIM8_BKIN. |
| 90 | PB4 | bidirectional | 5V tolerant GPIO with fail-safe capability; default function NJTRST, alternates include TIM3_CH1, SPI1_MISO, USART2_TX, SPI3_MISO and TIM8_ETR. |
| 91 | PB5 | bidirectional | 5V tolerant GPIO with fail-safe capability; alternates include I2C1_SMBA, SPI3_MOSI, I2S3_SD, ETH_MII_PPS_OUT, TIM3_CH2, SPI1_MOSI, CAN2_RX, USART2_RX and TIM1_BKIN. |
| 92 | PB6 | bidirectional | 3.3V tolerant I/O with fail-safe capability; alternates include I2C1_SCL, TIM4F_CH1, TSC_CHN20, USART1_TX, CAN2_TX, ETH_MII_PPS_OUT and COMP5_OUT. |
| 93 | PB7 | bidirectional | 3.3V tolerant I/O with fail-safe capability; alternates include I2C1_SDA, TIM4F_CH2, TSC_CHN21, USART1_RX, ETH_MII_TXD3 and COMP6_OUT. |
| 94 | BOOT0 | input | Boot mode select input with input pull-down. |
| 95 | PB8 | bidirectional | 3.3V tolerant I/O with fail-safe capability; alternates include TIM4F_CH3, SDIO_D4, ETH_MII_TXD3, TSC_CN22, I2C1_SCL, CAN1_RX, UART5_TX and COMP1_OUT. |
| 96 | PB9 | bidirectional | 3.3V tolerant I/O with fail-safe capability; alternates include TIM4F_CH4, SDIO_D5, TSC_CHN23, I2C1_SDA, CAN1_TX, UART5_RX and COMP2_OUT. |
| 97 | PE0 | bidirectional | 5V tolerant GPIO with fail-safe capability; alternate TIM4F_ETR. |
| 98 | PE1 | bidirectional | 5V tolerant GPIO with fail-safe capability; no alternate function is listed in table 3-1. |
| 99 | VSS_3 | power_in | Ground pin; all voltages are referenced to VSS. |
| 100 | VDD_3 | power_in | Digital supply pin; VDD 1.8~3.6V powers the I/O pins and internal regulator. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Nations Technologies Inc |
| Package | LQFP-100(14x14) |
| Category | Embedded Processors & Controllers |
| Pins | 100 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Output low-level voltage | VOL | 0.4 | V | VDD=3.3V,IOL(4)= 2/4/8/12 | 62 | ||
| Output high-level voltage | VOH | 2.4 | V | VDD=3.3V,IOH(4)= 2/4/8/12 | 62 | ||
| Output high-level voltage | VOH | 1.8 | V | VDD=2.5V,IOH(4)= 2/4/8/12 | 62 | ||
| NRST input low-level voltage | VIL(NRST) | 0.8 | V | VDD=3.3V | 64 | ||
| NRST input high-level voltage | VIH(NRST) | 2 | V | VDD=3.3V | 64 | ||
| NRST input filtered pulse | VF(NRST) | 100 | ns | 64 | |||
| NRST input non-filtered pulse | VNF(NRST) | 300 | ns | 64 | |||
| NRST weak pull-up equivalent resistance | RPU | 30 | 50 | 70 | kΩ | VIN= VIH | 64 |
| Timer resolution time | tres(TIM) | 6.95 | ns | fTIMxCLK= 144MHz | 64 | ||
| Timer external clock frequency on CH1 to CH4 | fEXT | 0 | 72 | MHz | fTIMxCLK= 144MHz | 64 | |
| Timer resolution | ResTIM | 16 | 位 | 64 | |||
| 16-bit counter clock period, internal clock selected | tCOUNTER | 1 | 65536 | tTIMxCLK | 选择了内部时钟时 | 64 | |
| 16-bit counter clock period, internal clock selected | tCOUNTER | 0.00695 | 455 | μs | fTIMxCLK= 144MHz | 64 | |
| Maximum possible count | tMAX_COUNT | 29.8 | s | fTIMxCLK= 144MHz | 64 | ||
| I2C interface frequency, standard mode | fSCL | 0 | 100 | KHz | 标准模式 | 65 | |
| I2C interface frequency, fast mode | fSCL | 0 | 400 | KHz | 快速模式 | 65 | |
| I2C interface frequency, fast+ mode | fSCL | 0 | 1000 | KHz | 快速+模式 | 65 | |
| SDA setup time, standard mode | tsu(SDA) | 250 | ns | 标准模式 | 65 | ||
| SDA setup time, fast mode | tsu(SDA) | 100 | ns | 快速模式 | 65 | ||
| SDA setup time, fast+ mode | tsu(SDA) | 50 | ns | 快速+模式 | 65 | ||
| SPI1 clock frequency, master mode | fSCLK | 36 | MHz | 主模式 | 66 | ||
| SPI1 clock frequency, slave mode | fSCLK | 36 | MHz | 从模式 | 66 | ||
| SPI1 SCLK rise and fall time | tr(SCLK)tf(SCLK) | 6 | ns | 负载电容:C = 30pF | 66 | ||
| SPI1 slave input clock duty cycle | DuCy(SCK) | 30 | 70 | % | SPI从模式 | 66 | |
| SPI1 data input setup time, master | tsu(MI) | 3.5 | ns | 主模式 | 66 | ||
| SPI1 data input setup time, slave | tsu(SI) | 3 | ns | 从模式 | 66 | ||
| SPI1 data input hold time, master | th(MI) | 3 | ns | 主模式 | 66 | ||
| SPI1 data input hold time, slave | th(SI) | 3 | ns | 从模式 | 66 | ||
| SPI1 data output valid time, slave | tv(SO) | 12.5 | ns | 从模式(使能边沿之后) | 66 | ||
| SPI1 data output valid time, master | tv(MO) | 6.5 | ns | 主模式(使能边沿之后) | 66 | ||
| SPI1 data output hold time, slave | th(SO) | 5 | ns | 从模式(使能边沿之后) | 66 | ||
| USB operating voltage | VDD | 3 | 3.6 | V | 73 | ||
| USB transceiver startup time | tSTARTUP | 1 | μs | 73 | |||
| Differential input sensitivity | VDI | 0.2 | V | 73 | |||
| Differential common-mode range | VCM | 0.8 | 2.5 | V | 包含VDI范围 | 73 | |
| Single-ended receiver threshold | VSE | 1.3 | 2 | V | 73 | ||
| Static output low level | VOL | 0.3 | V | 1.5kΩ的RL接至3.6V | 73 | ||
| Static output high level | VOH | 2.8 | 3.6 | V | 15kΩ的RL接至VSS | 73 | |
| USB data rise time | tr | 4 | 20 | ns | CL ≤ 50pF | 74 | |
| USB data fall time | tf | 4 | 20 | ns | CL ≤ 50pF | 74 | |
| Output signal crossover voltage | VCRS | 1.3 | 2 | V | 74 | ||
| Output series matching resistance | Rs | 27 | 39 | Ohm | 需匹配电阻外置,靠近芯片引脚 | 74 | |
| Ethernet operating voltage | VDD | 3 | 3.6 | V | 74 | ||
| MDC clock period (2.38MHz) | tMDC | 400 | 400 | 403 | ns | 75 | |
| MDC write data valid time | td(MDIO) | 4.5 | 10 | 12 | ns | MDC写数据有效时间 | 75 |
| Read data setup time | tsu(MDIO) | 14 | ns | 75 | |||
| Read data hold time | th(MDIO) | 0 | ns | 75 | |||
| Receive data setup time (RMII) | tsu(RXD) | 3.5 | ns | 75 | |||
| Receive data hold time (RMII) | tih(RXD) | 2 | ns | 75 | |||
| Carrier sense setup time (RMII) | tsu(DV) | 4 | ns | 75 | |||
| Carrier sense hold time (RMII) | tih(DV) | 2 | ns | 75 | |||
| Transmit enable valid delay (RMII) | td(TXEN) | 3.5 | 6.5 | 12.5 | ns | 75 | |
| Clock frequency in data transfer mode | fPP | 0 | 48 | MHz | CL ≤ 30pF | 73 | |
| Clock low time | tW(CKL) | 32 | ns | fPP = 16 MHz, CL ≤ 30pF | 73 | ||
| Clock high time | tW(CKH) | 30 | ns | CL ≤ 30pF | 73 | ||
| CMD and D input setup time | tISU | 1 | ns | CL ≤ 30pF | 73 | ||
| CMD and D input hold time | tIH | 1 | ns | CL ≤ 30pF | 73 | ||
| CMD and D output valid time (MMC and SD high speed) | tOV | 6 | ns | CL ≤ 30pF | 73 |
CAD (KiCad official)
- Symbol:
N32G457VEL7 - Footprint:
Package_QFP:LQFP-100_14x14mm_P0.5mm - 3D model: LQFP-100(14x14) (KiCad packages3D, STEP)
- 3D model files:
n32g457vel7-etched.step/n32g457vel7-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);n32g457vel7.step/n32g457vel7.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Nations Technologies Inc datasheet (91 pp, sha256
4b9a0eb90ea66c24, retrieved 2026-11-05, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# N32G457VEL7
**Nations Technologies Inc** · Microcontroller Units (MCUs/MPUs/SOCs) · LQFP-100(14x14)
N32G457VEL7 from Nations Technologies Inc, in a LQFP-100(14x14). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | PE2 | bidirectional | 5V tolerant GPIO with default function PE2; alternates include TRACECK, UART6_TX and DVP_HSYNC. |
| 2 | PE3 | bidirectional | 5V tolerant GPIO with default function PE3; alternates include TRACED0, UART6_RX and DVP_VSYNC. |
| 3 | PE4 | bidirectional | 5V tolerant GPIO with default function PE4; alternates include TRACED1 and DVP_PCLK. |
| 4 | PE5 | bidirectional | 5V tolerant GPIO with default function PE5; alternates include TRACED2 and DVP_D0. |
| 5 | PE6 | bidirectional | 5V tolerant GPIO with default function PE6; alternates include TRACED3 and DVP_D1. |
| 6 | VBAT | power_in | Backup supply 1.8~3.6V that powers the RTC, the external 32kHz oscillator and backup registers when VDD is off. |
| 7 | PC13-TAMPER-RTC | bidirectional | Standard 3.3V I/O powered through a switch limited to 3mA; as output it is limited to 2MHz mode, 30pF maximum load and no current sourcing. |
| 8 | PC14-OSC32_IN | bidirectional | Standard 3.3V I/O powered through a switch limited to 3mA; as output it is limited to 2MHz mode and 30pF maximum load. |
| 9 | PC15-OSC32_OUT | bidirectional | Standard 3.3V I/O powered through a switch limited to 3mA; as output it is limited to 2MHz mode and 30pF maximum load. |
| 10 | VSS_5 | power_in | Ground pin; all voltages are referenced to VSS. |
| 11 | VDD_5 | power_in | Digital supply pin; VDD 1.8~3.6V powers the I/O pins and internal regulator. |
| 12 | OSC_IN | input | HSE oscillator input for a 4~32MHz crystal or resonator or an external clock, with high level 0.8VDD to VDD. |
| 13 | OSC_OUT | output | HSE oscillator output for the 4~32MHz crystal or resonator. |
| 14 | NRST | bidirectional | Active-low external reset pin with internal pull-up resistor of 30~70kOhm. |
| 15 | PC0 | bidirectional | 3.3V tolerant I/O with analog function; alternates include ADC12_IN6, I2C3_SCL, COMP7_INM, DVP_D2 and UART6_TX. |
| 16 | PC1 | bidirectional | 3.3V tolerant I/O with analog function; alternates include ADC12_IN7, ETH_MII_MDC, ETH_RMII_MDC, I2C3_SDA, COMP7_INP and UART6_RX. |
| 17 | PC2 | bidirectional | 3.3V tolerant I/O with analog function; alternates include ADC12_IN8, ETH_MII_TXD2, COMP7_OUT, UART7_TX, SPI3_NSS and I2S3_WS. |
| 18 | PC3 | bidirectional | 3.3V tolerant I/O with analog function; alternates include ADC12_IN9, ETH_MII_TX_CLK, UART7_RX, SPI3_SCK, I2S3_CK, OPAMP3_VINP, OPAMP4_VINP and COMP5_INP. |
| 19 | VSSA | power_in | Analog ground for ADC, DAC, OPAMP, COMP and TSC; must be connected to VSS. |
| 20 | VREF- | power_in | Negative ADC reference voltage; ADC input range is VREF- to VREF+. |
| 21 | VREF+ | power_in | Positive reference voltage for the ADC and DAC; it must always be below VDDA for the DAC. |
| 22 | VDDA | power_in | Analog supply 1.8~3.6V for ADC, DAC, OPAMP, COMP and TSC; must be the same as VDD. |
| 23 | PA0-WKUP | bidirectional | 3.3V tolerant I/O with analog function and WKUP wake-up input; alternates include ADC1_IN1, TIM2_CH1_ETR, USART2_CTS and COMP1_INM. |
| 24 | PA1 | bidirectional | 3.3V tolerant I/O with analog function; alternates include ADC1_IN2, USART2_RTS, TIM5_CH2, ETH_RMII_REF_CLK, DVP_HSYNC, COMP1_INP and OPAMP1_VINP. |
| 25 | PA2 | bidirectional | 3.3V tolerant I/O with analog function; alternates include ADC12_IN11, USART2_TX, TIM5_CH3, ETH_RMII_MDIO, DVP_VSYNC, OPAMP1_INM and COMP3_OUT. |
| 26 | PA3 | bidirectional | 3.3V tolerant I/O with analog function; alternates include ADC1_IN4, USART2_RX, TIM5_CH4, ETH_MII_COL, DVP_PCLK, OPAMP1_VINM, OPAMP1_VINP and COMP5_INP. |
| 27 | VSS_4 | power_in | Ground pin; all voltages are referenced to VSS. |
| 28 | VDD_4 | power_in | Digital supply pin; VDD 1.8~3.6V powers the I/O pins and internal regulator. |
| 29 | PA4 | bidirectional | 3.3V tolerant I/O with analog function; alternates include SPI1_NSS, USART2_CK, DAC_OUT1, ADC2_IN1, DVP_D0, QSPI_NSS, TSC_CHN0 and I2C2_SCL. |
| 30 | PA5 | bidirectional | 3.3V tolerant I/O with analog function; alternates include SPI1_SCK, DAC_OUT2, ADC2_IN2, DVP_D1, QSPI_SCK, TSC_CHN1 and I2C2_SDA. |
| 31 | PA6 | bidirectional | 3.3V tolerant I/O with analog function; alternates include SPI1_MISO, TIM8_BKIN, ADC1_IN3, TIM3_CH1, DVP_D2, QSPI_IO0, COMP2_OUT, TIM1_BKIN and OPAMP1_VOUT. |
| 32 | PA7 | bidirectional | 3.3V tolerant I/O with analog function; alternates include SPI1_MOSI, TIM8_CH1N, ADC2_IN4, TIM3_CH2, DVP_D3, ETH_RMII_CRS_DV, QSPI_IO1, TIM1_CH1N and COMP2_INP. |
| 33 | PC4 | bidirectional | 3.3V tolerant I/O with analog function; alternates include ADC2_IN5, DVP_D4, ETH_RMII_RXD0, QSPI_IO2, UART7_TX, I2C3_SCL, OPAMP3_VINM and COMP4_INM. |
| 34 | PC5 | bidirectional | 3.3V tolerant I/O with analog function; alternates include ADC2_IN12, ETH_RMII_RXD1, DVP_D5, QSPI_IO3, UART7_RX, COMP4_OUT, I2C3_SDA, OPAMP4_VINP and COMP6_INP. |
| 35 | PB0 | bidirectional | 3.3V tolerant I/O with analog function; alternates include ADC3_IN12, TIM3_CH3, TIM8_CH2N, ETH_MII_RXD2, DVP_D6, COMP5_OUT, TIM1_CH2N, UART6_TX, OPAMP2_VINP and COMP3_INP. |
| 36 | PB1 | bidirectional | 3.3V tolerant I/O with analog function; alternates include ADC2_IN3, TIM3_CH4, TIM8_CH3N, ETH_MII_RXD3, DVP_D7, TIM1_CH3N, OPAMP2_VOUT, UART6_RX, COMP2_INM and COMP1_OUT. |
| 37 | PB2-BOOT1 | bidirectional | 3.3V tolerant I/O with analog function; BOOT1 is an input with pull-down; alternates include ADC2_IN13, DVP_D3, UART4_TX and SPI1_NSS. |
| 38 | PE7 | bidirectional | 3.3V tolerant I/O with analog function; alternates include ADC3_IN13, TIM1_ETR, UART4_RX, SPI1_SCK and COMP3_INM. |
| 39 | PE8 | bidirectional | 3.3V tolerant I/O with analog function; alternates include ADC34_IN6, TIM1_CH1N, UART5_TX, SDIO_D0, SPI1_MISO, OPAMP2_INP and COMP2_INM. |
| 40 | PE9 | bidirectional | 3.3V tolerant I/O with analog function; alternates include ADC3_IN2, TIM1_CH1, UART5_RX, SDIO_D1 and SPI1_MOSI. |
| 41 | PE10 | bidirectional | 3.3V tolerant I/O with analog function; alternates include ADC3_IN14, TIM1_CH2N, SDIO_D2, SPI2_NSS and I2S2_WS. |
| 42 | PE11 | bidirectional | 3.3V tolerant I/O with analog function; alternates include ADC3_IN15, TIM1_CH2, SDIO_D3, SPI2_SCK and I2S2_CK. |
| 43 | PE12 | bidirectional | 3.3V tolerant I/O with analog function; alternates include ADC3_IN4, TIM1_CH3N, SDIO_CK and SPI2_MISO. |
| 44 | PE13 | bidirectional | 3.3V tolerant I/O with analog function; alternates include ADC3_IN3, TIM1_CH3, SPI2_MOSI, I2S2_SD and SDIO_CMD. |
| 45 | PE14 | bidirectional | 3.3V tolerant I/O with analog function; alternates include ADC4_IN1 and TIM1_CH4. |
| 46 | PE15 | bidirectional | 3.3V tolerant I/O with analog function; alternates include ADC4_IN2 and TIM1_BKIN. |
| 47 | PB10 | bidirectional | 3.3V tolerant I/O with analog function and fail-safe capability; alternates include I2C2_SCL, USART3_TX, ETH_MII_RX_ER, COMP3_OUT, TIM2_CH3, OPAMP3_VINM and DVP_D4. |
| 48 | PB11 | bidirectional | 3.3V tolerant I/O with analog function; alternates include I2C2_SDA, USART3_RX, ETH_MII_TX_EN, ADC3_IN1, TIM2_CH4, OPAMP3_VOUT, COMP2_INP, COMP5_OUT and DVP_D5. |
| 49 | VSS_1 | power_in | Ground pin; all voltages are referenced to VSS. |
| 50 | VDD_1 | power_in | Digital supply pin; VDD 1.8~3.6V powers the I/O pins and internal regulator. |
| 51 | PB12 | bidirectional | 3.3V tolerant I/O with analog function; alternates include SPI2_NSS, I2S2_WS, I2C2_SMBA, USART3_CK, TIM1_BKIN, CAN2_RX, ETH_MII_TXD0, ADC4_IN3, COMP3_INM and OPAMP4_VOUT. |
| 52 | PB13 | bidirectional | 3.3V tolerant I/O with analog function; alternates include SPI2_SCK, I2S2_CK, USART3_CTS, TIM1_CH1N, CAN2_TX, ETH_MII_TXD1, ADC3_IN5, UART5_TX and COMP4_INM. |
| 53 | PB14 | bidirectional | 3.3V tolerant I/O with analog function; alternates include SPI2_MISO, TIM1_CH2N, USART3_RTS, ADC4_IN4, TSC_CHN2, COMP3_INP and UART5_RX. |
| 54 | PB15 | bidirectional | 3.3V tolerant I/O with analog function; alternates include SPI2_MOSI, I2S2_SD, TIM1_CH3N, ADC4_IN5, TSC_CHN3 and COMP4_INP. |
| 55 | PD8 | bidirectional | 3.3V tolerant I/O with analog function; alternates include ADC4_IN12, TSC_CHN4, USART3_TX, ETH_RMII_CRS_DV, OPAMP4_VINM, SPI3_NSS, I2S3_WS, CAN1_RX and COMP6_INM. |
| 56 | PD9 | bidirectional | 3.3V tolerant I/O with analog function; alternates include ADC4_IN13, TSC_CHN5, USART3_RX, ETH_RMII_RXD0, SPI3_SCK, I2S3_CK, CAN1_TX and COMP6_INP. |
| 57 | PD10 | bidirectional | 3.3V tolerant I/O with analog function; alternates include ADC34_IN7, USART3_CK, ETH_RMII_RXD1, CAN2_RX and COMP5_INM. |
| 58 | PD11 | bidirectional | 3.3V tolerant I/O with analog function; alternates include ADC34_IN8, TSC_CHN6, USART3_CTS, ETH_MII_RXD2, CAN2_TX and SPI3_MISO. |
| 59 | PD12 | bidirectional | 3.3V tolerant I/O with analog function; alternates include ADC34_IN9, TSC_CHN7, TIM4F_CH1, USART3_RTS, ETH_MII_RXD3, SPI3_MOSI, I2S3_SD and COMP7_OUT. |
| 60 | PD13 | bidirectional | 3.3V tolerant I/O with analog function; alternates include ADC34_IN10 and TIM4F_CH2. |
| 61 | PD14 | bidirectional | 3.3V tolerant I/O with analog function; alternates include ADC34_IN11, TIM4F_CH3, I2C4_SCL and TIM8_CH1. |
| 62 | PD15 | bidirectional | 5V tolerant GPIO with fail-safe capability; alternates include TIM4F_CH4, I2C4_SDA and TIM8_CH2. |
| 63 | PC6 | bidirectional | 3.3V tolerant I/O with fail-safe capability; alternates include I2S2_MCK, TIM8_CH1, SDIO_D6, I2C4_SCL, TSC_CHN8, TIM3_CH1, SPI2_NSS, I2S2_WS and USART2_CTS. |
| 64 | PC7 | bidirectional | 3.3V tolerant I/O with fail-safe capability; alternates include I2S3_MCK, TIM8_CH2, SDIO_D7, I2C4_SDA, TSC_CHN9, TIM3_CH2, SPI2_SCK, I2S2_CK and USART2_RTS. |
| 65 | PC8 | bidirectional | 3.3V tolerant I/O with fail-safe capability; alternates include TIM8_CH3, SDIO_D0, TSC_CHN10, TIM3_CH3, SPI2_MISO and USART2_TX. |
| 66 | PC9 | bidirectional | 3.3V tolerant I/O with fail-safe capability; alternates include TIM8_CH4, SDIO_D1, TSC_CHN11, COMP6_OUT, TIM3_CH4, SPI2_MOSI, I2S2_SD, USART2_RX, OPAMP3_INP and OPAMP4_INM. |
| 67 | PA8 | bidirectional | 5V tolerant GPIO with fail-safe capability; alternates include USART1_CK, TIM1_CH1 and MCO. |
| 68 | PA9 | bidirectional | 5V tolerant GPIO with fail-safe capability; alternates include USART1_TX, TIM1_CH2, TSC_DOUT and I2C4_SCL. |
| 69 | PA10 | bidirectional | 5V tolerant GPIO with fail-safe capability; alternates include USART1_RX, TIM1_CH3 and I2C4_SDA. |
| 70 | PA11 | bidirectional | 5V tolerant GPIO with fail-safe capability; alternates include USART1_CTS, USBDM, CAN1_RX, TIM1_CH4, COMP5_OUT and COMP1_OUT. |
| 71 | PA12 | bidirectional | 5V tolerant GPIO with fail-safe capability; alternates include USART1_RTS, USBDP, CAN1_TX, TIM1_ETR, COMP6_OUT and COMP2_OUT. |
| 72 | PA13 | bidirectional | 5V tolerant GPIO with fail-safe capability; default function JTMS-SWDIO, alternate UART4_TX. |
| 73 | NC | unconnected | Listed as Not connected for the LQFP100 package in table 3-1. |
| 74 | VSS_2 | power_in | Ground pin; all voltages are referenced to VSS. |
| 75 | VDD_2 | power_in | Digital supply pin; VDD 1.8~3.6V powers the I/O pins and internal regulator. |
| 76 | PA14 | bidirectional | 5V tolerant GPIO with fail-safe capability; default function JTCK-SWCLK, alternate UART4_RX. |
| 77 | PA15 | bidirectional | 5V tolerant GPIO with fail-safe capability; default function JTDI, alternates include SPI3_NSS, I2S3_WS, TIM2_CH1_ETR, SPI1_NSS, USART2_CTS and TIM8_CH1N. |
| 78 | PC10 | bidirectional | 3.3V tolerant I/O with fail-safe capability; alternates include UART4_TX, SDIO_D2, TSC_CHN12, USART3_TX, SPI3_SCK, I2S3_CK, QSPI_NSS and COMP3_OUT. |
| 79 | PC11 | bidirectional | 3.3V tolerant I/O with fail-safe capability; alternates include UART4_RX, SDIO_D3, TSC_CHN13, USART3_RX, SPI3_MISO, QSPI_SCK and COMP4_OUT. |
| 80 | PC12 | bidirectional | 3.3V tolerant I/O with fail-safe capability; alternates include UART5_TX, SDIO_CK, TSC_CHN14, USART3_CK, SPI3_MOSI, I2S3_SD, QSPI_IO0 and TIM8_CH2N. |
| 81 | PD0 | bidirectional | 5V tolerant GPIO with fail-safe capability; PD0 is an inherent function pin on LQFP100 needing no remap; alternates include CAN1_RX, UART4_TX and QSPI_IO1. |
| 82 | PD1 | bidirectional | 5V tolerant GPIO with fail-safe capability; PD1 is an inherent function pin on LQFP100 needing no remap; alternates include CAN1_TX, UART4_RX and QSPI_IO2. |
| 83 | PD2 | bidirectional | 3.3V tolerant I/O with fail-safe capability; alternates include TIM3_ETR, UART5_RX, SDIO_CMD, TSC_CHN15, SPI3_NSS, I2S3_WS, QSPI_IO3 and TIM8_CH3N. |
| 84 | PD3 | bidirectional | 5V tolerant GPIO with fail-safe capability; alternate USART2_CTS. |
| 85 | PD4 | bidirectional | 3.3V tolerant I/O with fail-safe capability; alternates include TSC_CHN16 and USART2_RTS. |
| 86 | PD5 | bidirectional | 3.3V tolerant I/O with fail-safe capability; alternates include TSC_CHN17 and USART2_TX. |
| 87 | PD6 | bidirectional | 3.3V tolerant I/O with fail-safe capability; alternates include TSC_CHN18 and USART2_RX. |
| 88 | PD7 | bidirectional | 3.3V tolerant I/O with fail-safe capability; alternates include TSC_CHN19 and USART2_CK. |
| 89 | PB3 | bidirectional | 5V tolerant GPIO with fail-safe capability; default function JTDO, alternates include TRACESWO, TIM2_CH2, SPI1_SCK, USART2_RTS, SPI3_SCK and TIM8_BKIN. |
| 90 | PB4 | bidirectional | 5V tolerant GPIO with fail-safe capability; default function NJTRST, alternates include TIM3_CH1, SPI1_MISO, USART2_TX, SPI3_MISO and TIM8_ETR. |
| 91 | PB5 | bidirectional | 5V tolerant GPIO with fail-safe capability; alternates include I2C1_SMBA, SPI3_MOSI, I2S3_SD, ETH_MII_PPS_OUT, TIM3_CH2, SPI1_MOSI, CAN2_RX, USART2_RX and TIM1_BKIN. |
| 92 | PB6 | bidirectional | 3.3V tolerant I/O with fail-safe capability; alternates include I2C1_SCL, TIM4F_CH1, TSC_CHN20, USART1_TX, CAN2_TX, ETH_MII_PPS_OUT and COMP5_OUT. |
| 93 | PB7 | bidirectional | 3.3V tolerant I/O with fail-safe capability; alternates include I2C1_SDA, TIM4F_CH2, TSC_CHN21, USART1_RX, ETH_MII_TXD3 and COMP6_OUT. |
| 94 | BOOT0 | input | Boot mode select input with input pull-down. |
| 95 | PB8 | bidirectional | 3.3V tolerant I/O with fail-safe capability; alternates include TIM4F_CH3, SDIO_D4, ETH_MII_TXD3, TSC_CN22, I2C1_SCL, CAN1_RX, UART5_TX and COMP1_OUT. |
| 96 | PB9 | bidirectional | 3.3V tolerant I/O with fail-safe capability; alternates include TIM4F_CH4, SDIO_D5, TSC_CHN23, I2C1_SDA, CAN1_TX, UART5_RX and COMP2_OUT. |
| 97 | PE0 | bidirectional | 5V tolerant GPIO with fail-safe capability; alternate TIM4F_ETR. |
| 98 | PE1 | bidirectional | 5V tolerant GPIO with fail-safe capability; no alternate function is listed in table 3-1. |
| 99 | VSS_3 | power_in | Ground pin; all voltages are referenced to VSS. |
| 100 | VDD_3 | power_in | Digital supply pin; VDD 1.8~3.6V powers the I/O pins and internal regulator. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Nations Technologies Inc |
| Package | LQFP-100(14x14) |
| Category | Embedded Processors & Controllers |
| Pins | 100 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Output low-level voltage | VOL | | | 0.4 | V | VDD=3.3V,IOL(4)= 2/4/8/12 | 62 |
| Output high-level voltage | VOH | 2.4 | | | V | VDD=3.3V,IOH(4)= 2/4/8/12 | 62 |
| Output high-level voltage | VOH | 1.8 | | | V | VDD=2.5V,IOH(4)= 2/4/8/12 | 62 |
| NRST input low-level voltage | VIL(NRST) | | | 0.8 | V | VDD=3.3V | 64 |
| NRST input high-level voltage | VIH(NRST) | 2 | | | V | VDD=3.3V | 64 |
| NRST input filtered pulse | VF(NRST) | | | 100 | ns | | 64 |
| NRST input non-filtered pulse | VNF(NRST) | 300 | | | ns | | 64 |
| NRST weak pull-up equivalent resistance | RPU | 30 | 50 | 70 | kΩ | VIN= VIH | 64 |
| Timer resolution time | tres(TIM) | 6.95 | | | ns | fTIMxCLK= 144MHz | 64 |
| Timer external clock frequency on CH1 to CH4 | fEXT | 0 | | 72 | MHz | fTIMxCLK= 144MHz | 64 |
| Timer resolution | ResTIM | | | 16 | 位 | | 64 |
| 16-bit counter clock period, internal clock selected | tCOUNTER | 1 | | 65536 | tTIMxCLK | 选择了内部时钟时 | 64 |
| 16-bit counter clock period, internal clock selected | tCOUNTER | 0.00695 | | 455 | μs | fTIMxCLK= 144MHz | 64 |
| Maximum possible count | tMAX_COUNT | | | 29.8 | s | fTIMxCLK= 144MHz | 64 |
| I2C interface frequency, standard mode | fSCL | 0 | | 100 | KHz | 标准模式 | 65 |
| I2C interface frequency, fast mode | fSCL | 0 | | 400 | KHz | 快速模式 | 65 |
| I2C interface frequency, fast+ mode | fSCL | 0 | | 1000 | KHz | 快速+模式 | 65 |
| SDA setup time, standard mode | tsu(SDA) | 250 | | | ns | 标准模式 | 65 |
| SDA setup time, fast mode | tsu(SDA) | 100 | | | ns | 快速模式 | 65 |
| SDA setup time, fast+ mode | tsu(SDA) | 50 | | | ns | 快速+模式 | 65 |
| SPI1 clock frequency, master mode | fSCLK | | | 36 | MHz | 主模式 | 66 |
| SPI1 clock frequency, slave mode | fSCLK | | | 36 | MHz | 从模式 | 66 |
| SPI1 SCLK rise and fall time | tr(SCLK)tf(SCLK) | | | 6 | ns | 负载电容:C = 30pF | 66 |
| SPI1 slave input clock duty cycle | DuCy(SCK) | 30 | | 70 | % | SPI从模式 | 66 |
| SPI1 data input setup time, master | tsu(MI) | 3.5 | | | ns | 主模式 | 66 |
| SPI1 data input setup time, slave | tsu(SI) | 3 | | | ns | 从模式 | 66 |
| SPI1 data input hold time, master | th(MI) | 3 | | | ns | 主模式 | 66 |
| SPI1 data input hold time, slave | th(SI) | 3 | | | ns | 从模式 | 66 |
| SPI1 data output valid time, slave | tv(SO) | | | 12.5 | ns | 从模式(使能边沿之后) | 66 |
| SPI1 data output valid time, master | tv(MO) | | | 6.5 | ns | 主模式(使能边沿之后) | 66 |
| SPI1 data output hold time, slave | th(SO) | 5 | | | ns | 从模式(使能边沿之后) | 66 |
| USB operating voltage | VDD | 3 | | 3.6 | V | | 73 |
| USB transceiver startup time | tSTARTUP | | | 1 | μs | | 73 |
| Differential input sensitivity | VDI | 0.2 | | | V | | 73 |
| Differential common-mode range | VCM | 0.8 | | 2.5 | V | 包含VDI范围 | 73 |
| Single-ended receiver threshold | VSE | 1.3 | | 2 | V | | 73 |
| Static output low level | VOL | | | 0.3 | V | 1.5kΩ的RL接至3.6V | 73 |
| Static output high level | VOH | 2.8 | | 3.6 | V | 15kΩ的RL接至VSS | 73 |
| USB data rise time | tr | 4 | | 20 | ns | CL ≤ 50pF | 74 |
| USB data fall time | tf | 4 | | 20 | ns | CL ≤ 50pF | 74 |
| Output signal crossover voltage | VCRS | 1.3 | | 2 | V | | 74 |
| Output series matching resistance | Rs | 27 | | 39 | Ohm | 需匹配电阻外置,靠近芯片引脚 | 74 |
| Ethernet operating voltage | VDD | 3 | | 3.6 | V | | 74 |
| MDC clock period (2.38MHz) | tMDC | 400 | 400 | 403 | ns | | 75 |
| MDC write data valid time | td(MDIO) | 4.5 | 10 | 12 | ns | MDC写数据有效时间 | 75 |
| Read data setup time | tsu(MDIO) | 14 | | | ns | | 75 |
| Read data hold time | th(MDIO) | 0 | | | ns | | 75 |
| Receive data setup time (RMII) | tsu(RXD) | 3.5 | | | ns | | 75 |
| Receive data hold time (RMII) | tih(RXD) | 2 | | | ns | | 75 |
| Carrier sense setup time (RMII) | tsu(DV) | 4 | | | ns | | 75 |
| Carrier sense hold time (RMII) | tih(DV) | 2 | | | ns | | 75 |
| Transmit enable valid delay (RMII) | td(TXEN) | 3.5 | 6.5 | 12.5 | ns | | 75 |
| Clock frequency in data transfer mode | fPP | 0 | | 48 | MHz | CL ≤ 30pF | 73 |
| Clock low time | tW(CKL) | 32 | | | ns | fPP = 16 MHz, CL ≤ 30pF | 73 |
| Clock high time | tW(CKH) | 30 | | | ns | CL ≤ 30pF | 73 |
| CMD and D input setup time | tISU | 1 | | | ns | CL ≤ 30pF | 73 |
| CMD and D input hold time | tIH | 1 | | | ns | CL ≤ 30pF | 73 |
| CMD and D output valid time (MMC and SD high speed) | tOV | | | 6 | ns | CL ≤ 30pF | 73 |
## CAD (KiCad official)
- Symbol: `N32G457VEL7`
- Footprint: `Package_QFP:LQFP-100_14x14mm_P0.5mm`
- 3D model: LQFP-100(14x14) (KiCad packages3D, STEP)
- 3D model files: `n32g457vel7-etched.step` / `n32g457vel7-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `n32g457vel7.step` / `n32g457vel7.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Nations Technologies Inc datasheet](docs/n32g457vel7-datasheet.pdf) (91 pp, sha256 `4b9a0eb90ea66c24`, retrieved 2026-11-05, tier: lcsc)
- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/n32g457vel7-datasheet.pdf)