3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownN32G452RCL7
Nations Technologies Inc · Other Processors and Microcontrollers (MCUs) · LQFP-64(10x10)
N32G452RCL7 from Nations Technologies Inc, in a LQFP-64(10x10). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VBAT | power_in | Backup-domain supply, 1.8V to 3.6V, powers the RTC, the external 32.768kHz oscillator and backup registers when VDD is off. |
| 2 | PC13-TAMPER-RTC | bidirectional | GPIO with TAMPER-RTC function, powered through a power switch limited to 3mA, so as an output only one of PC13/PC14/PC15 may be used at a time, at 2MHz, 30pF max, and not as a current source. |
| 3 | PC14-OSC32_IN | bidirectional | GPIO with LSE oscillator input OSC32_IN for a 32.768kHz crystal, subject to the same 3mA power-switch limit as PC13 (2MHz, 30pF max as output). |
| 4 | PC15-OSC32_OUT | bidirectional | GPIO with LSE oscillator output OSC32_OUT for a 32.768kHz crystal, subject to the same 3mA power-switch limit as PC13 (2MHz, 30pF max as output). |
| 5 | PD0-OSC_IN | input | HSE oscillator input for a 4MHz to 32MHz crystal or resonator; default function OSC_IN, PD0 only after software remap. |
| 6 | PD1-OSC_OUT | output | HSE oscillator output for a 4MHz to 32MHz crystal or resonator; default function OSC_OUT, PD1 only after software remap. |
| 7 | NRST | input | Active-low reset input with internal pull-up of 20kΩ to 50kΩ; pulses shorter than 100ns are filtered. |
| 8 | PC0 | bidirectional | Analog-capable GPIO with ADC12_IN6, I2C3_SCL and UART6_TX alternate functions. |
| 9 | PC1 | bidirectional | Analog-capable GPIO with ADC12_IN7, I2C3_SDA and UART6_RX alternate functions. |
| 10 | PC2 | bidirectional | Analog-capable GPIO with ADC12_IN8, UART7_TX, SPI3_NSS and I2S3_WS alternate functions. |
| 11 | PC3 | bidirectional | Analog-capable GPIO with ADC12_IN9, UART7_RX, SPI3_SCK and I2S3_CK alternate functions. |
| 12 | VSSA | power_in | Analog ground for ADC, DAC, reset block, RC oscillators and PLL; must be connected to VSS. |
| 13 | VDDA | power_in | Analog supply for ADC, DAC, reset block, RC oscillators and PLL, 1.8V to 3.6V, must equal VDD within 300mV. |
| 14 | PA0-WKUP | bidirectional | Analog-capable GPIO with WKUP wake-up input, ADC1_IN1, TIM2_CH1_ETR, TIM5_CH1, TIM8_ETR, SPI3_MISO and USART2_CTS. |
| 15 | PA1 | bidirectional | Analog-capable GPIO with USART2_RTS, ADC1_IN2, TIM5_CH2, TIM2_CH2, SPI3_MOSI and I2S3_SD alternate functions. |
| 16 | PA2 | bidirectional | Analog-capable GPIO with USART2_TX, TIM5_CH3, ADC12_IN11 and TIM2_CH3 alternate functions. |
| 17 | PA3 | bidirectional | Analog-capable GPIO with USART2_RX, TIM5_CH4, ADC1_IN4 and TIM2_CH4 alternate functions. |
| 18 | VSS_4 | power_in | Ground pin, connect to the board ground. |
| 19 | VDD_4 | power_in | Digital supply pin for I/O and internal regulator, 1.8V to 3.6V. |
| 20 | PA4 | bidirectional | Analog-capable GPIO with DAC_OUT1, ADC2_IN1, SPI1_NSS, USART2_CK, QSPI_NSS and I2C2_SCL alternate functions. |
| 21 | PA5 | bidirectional | Analog-capable GPIO with DAC_OUT2, ADC2_IN2, SPI1_SCK, QSPI_SCK and I2C2_SDA alternate functions. |
| 22 | PA6 | bidirectional | Analog-capable GPIO with ADC1_IN3, SPI1_MISO, TIM8_BKIN, TIM3_CH1, QSPI_IO0 and TIM1_BKIN alternate functions. |
| 23 | PA7 | bidirectional | Analog-capable GPIO with ADC2_IN4, SPI1_MOSI, TIM8_CH1N, TIM3_CH2, QSPI_IO1 and TIM1_CH1N alternate functions. |
| 24 | PC4 | bidirectional | Analog-capable GPIO with ADC2_IN5, QSPI_IO2, UART7_TX and I2C3_SCL alternate functions. |
| 25 | PC5 | bidirectional | Analog-capable GPIO with ADC2_IN12, QSPI_IO3, UART7_RX and I2C3_SDA alternate functions. |
| 26 | PB0 | bidirectional | Analog-capable GPIO with TIM3_CH3, TIM8_CH2N, TIM1_CH2N and UART6_TX alternate functions. |
| 27 | PB1 | bidirectional | Analog-capable GPIO with ADC2_IN3, TIM3_CH4, TIM8_CH3N, TIM1_CH3N and UART6_RX alternate functions. |
| 28 | PB2-BOOT1 | bidirectional | GPIO shared with BOOT1, which is an input with pull-down at reset, with ADC2_IN13, UART4_TX and SPI1_NSS alternate functions. |
| 29 | PB10 | bidirectional | Analog-capable GPIO with I2C2_SCL, USART3_TX, TIM2_CH3 and XFMC_D11 alternate functions. |
| 30 | PB11 | bidirectional | Analog-capable GPIO with I2C2_SDA, USART3_RX and TIM2_CH4 alternate functions. |
| 31 | VSS_1 | power_in | Ground pin, connect to the board ground. |
| 32 | VDD_1 | power_in | Digital supply pin for I/O and internal regulator, 1.8V to 3.6V. |
| 33 | PB12 | bidirectional | Analog-capable GPIO with SPI2_NSS, I2S2_WS, I2C2_SMBA, USART3_CK, TIM1_BKIN and CAN2_RX alternate functions. |
| 34 | PB13 | bidirectional | Analog-capable GPIO with SPI2_SCK, I2S2_CK, USART3_CTS, TIM1_CH1N, CAN2_TX and UART5_TX alternate functions. |
| 35 | PB14 | bidirectional | Analog-capable GPIO with SPI2_MISO, TIM1_CH2N, USART3_RTS and UART5_RX alternate functions. |
| 36 | PB15 | bidirectional | Analog-capable GPIO with SPI2_MOSI, I2S2_SD and TIM1_CH3N alternate functions. |
| 37 | PC6 | bidirectional | Analog-capable GPIO with I2S2_MCK, TIM8_CH1, SDIO_D6, I2C4_SCL, TIM3_CH1, SPI2_NSS and USART2_CTS alternate functions. |
| 38 | PC7 | bidirectional | Analog-capable GPIO with I2S3_MCK, TIM8_CH2, SDIO_D7, I2C4_SDA, TIM3_CH2, SPI2_SCK and USART2_RTS alternate functions. |
| 39 | PC8 | bidirectional | Analog-capable GPIO with TIM8_CH3, SDIO_D0, TIM3_CH3, SPI2_MISO and USART2_TX alternate functions. |
| 40 | PC9 | bidirectional | Analog-capable GPIO with TIM8_CH4, SDIO_D1, TIM3_CH4, SPI2_MOSI, I2S2_SD and USART2_RX alternate functions. |
| 41 | PA8 | bidirectional | 5V-tolerant GPIO with USART1_CK, TIM1_CH1 and MCO clock output alternate functions. |
| 42 | PA9 | bidirectional | 5V-tolerant GPIO with USART1_TX, TIM1_CH2 and I2C4_SCL alternate functions. |
| 43 | PA10 | bidirectional | 5V-tolerant GPIO with USART1_RX, TIM1_CH3, I2C4_SDA and XFMC_MWE alternate functions. |
| 44 | PA11 | bidirectional | 5V-tolerant GPIO with USART1_CTS, USBDM, CAN1_RX and TIM1_CH4 alternate functions. |
| 45 | PA12 | bidirectional | 5V-tolerant GPIO with USART1_RTS, USBDP, CAN1_TX and TIM1_ETR alternate functions. |
| 46 | PA13 | bidirectional | 5V-tolerant GPIO that is the JTMS/SWDIO debug pin at reset, also usable as UART4_TX. |
| 47 | VSS_2 | power_in | Ground pin, connect to the board ground. |
| 48 | VDD_2 | power_in | Digital supply pin for I/O and internal regulator, 1.8V to 3.6V. |
| 49 | PA14 | bidirectional | 5V-tolerant GPIO that is the JTCK/SWCLK debug pin at reset, also usable as UART4_RX. |
| 50 | PA15 | bidirectional | 5V-tolerant GPIO that is the JTDI debug pin at reset, with SPI1_NSS, SPI3_NSS, I2S3_WS, USART2_CTS, TIM2_CH1_ETR and TIM8_CH1N alternate functions. |
| 51 | PC10 | bidirectional | Analog-capable GPIO with UART4_TX, SDIO_D2, USART3_TX, SPI3_SCK, I2S3_CK and QSPI_NSS alternate functions. |
| 52 | PC11 | bidirectional | Analog-capable GPIO with UART4_RX, SDIO_D3, USART3_RX, SPI3_MISO and QSPI_SCK alternate functions. |
| 53 | PC12 | bidirectional | Analog-capable GPIO with UART5_TX, SDIO_CK, USART3_CK, SPI3_MOSI, I2S3_SD, QSPI_IO0 and TIM8_CH2N alternate functions. |
| 54 | PD2 | bidirectional | Analog-capable GPIO with TIM3_ETR, UART5_RX, SDIO_CMD, SPI3_NSS, I2S3_WS, QSPI_IO3 and TIM8_CH3N alternate functions. |
| 55 | PB3 | bidirectional | 5V-tolerant GPIO with JTDO/TRACESWO, SPI3_SCK, I2S3_CK, TIM2_CH2, SPI1_SCK, USART2_RTS and TIM8_BKIN alternate functions. |
| 56 | PB4 | bidirectional | 5V-tolerant GPIO that is NJTRST at reset, with SPI3_MISO, TIM3_CH1, SPI1_MISO, USART2_TX and TIM8_ETR alternate functions. |
| 57 | PB5 | bidirectional | 5V-tolerant GPIO with I2C1_SMBA, SPI3_MOSI, I2S3_SD, TIM3_CH2, SPI1_MOSI, CAN2_RX, USART2_RX and TIM1_BKIN alternate functions. |
| 58 | PB6 | bidirectional | Analog-capable GPIO with I2C1_SCL, TIM4_CH1, USART1_TX, CAN2_TX and XFMC_NE2 alternate functions. |
| 59 | PB7 | bidirectional | Analog-capable GPIO with I2C1_SDA, XFMC_NADV, TIM4_CH2 and USART1_RX alternate functions. |
| 60 | BOOT0 | input | Boot mode select input with input pull-down, used together with BOOT1 to select the startup memory. |
| 61 | PB8 | bidirectional | Analog-capable GPIO with TIM4_CH3, SDIO_D4, I2C1_SCL, CAN1_RX, UART5_TX and XFMC_NWAIT alternate functions. |
| 62 | PB9 | bidirectional | Analog-capable GPIO with TIM4_CH4, SDIO_D5, I2C1_SDA, CAN1_TX, UART5_RX and XFMC_NE1 alternate functions. |
| 63 | VSS_3 | power_in | Ground pin, connect to the board ground. |
| 64 | VDD_3 | power_in | Digital supply pin for I/O and internal regulator, 1.8V to 3.6V; the 4.7µF decoupling capacitor must connect to VDD3. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Nations Technologies Inc |
| Package | LQFP-64(10x10) |
| Category | Embedded Processors & Controllers |
| Pins | 64 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| SD/MMC clock frequency in data transfer mode | fPP | 0 | 48 | MHz | CL ≤ 30pF | 83 | |
| Clock low time | tW(CKL) | 32 | ns | fPP = 16 MHz, CL ≤ 30pF | 83 | ||
| Clock high time | tW(CKH) | 30 | ns | CL ≤ 30pF | 83 | ||
| Clock rise time | tr | 6 | ns | CL ≤ 30pF | 83 | ||
| Clock fall time | tf | 6 | ns | CL ≤ 30pF | 83 | ||
| CMD, D input setup time (referenced to CK) | tISU | 2 | ns | CL ≤ 30pF | 83 | ||
| CMD, D input hold time (referenced to CK) | tIH | 2 | ns | CL ≤ 30pF | 83 | ||
| CMD, D output valid time, MMC and SD high-speed mode (referenced to CK) | tOV | 14 | ns | CL ≤ 30pF | 83 | ||
| CMD, D output hold time, MMC and SD high-speed mode (referenced to CK) | tOH | 2.5 | ns | CL ≤ 30pF | 83 | ||
| CMD, D output valid default time, SD default mode (referenced to CK) | tOVD | 9 | ns | CL ≤ 30pF | 84 | ||
| CMD, D output hold default time, SD default mode (referenced to CK) | tOHD | -2 | ns | CL ≤ 30pF | 84 | ||
| USB transceiver startup time | tSTARTUP | 1 | μs | 84 | |||
| USB operating voltage | VDD | 3 | 3.6 | V | USB full-speed operation; correct USB function guaranteed at 2.7 V per footnote | 84 | |
| Differential input sensitivity | VDI | 0.2 | V | I(USBDP, USBDM) | 84 | ||
| Differential common-mode range | VCM | 0.8 | 2.5 | V | 包含VDI范围 | 84 | |
| Single-ended receiver threshold | VSE | 1.3 | 2 | V | 84 | ||
| Static output low level | VOL | 0.3 | V | 1.5kΩ RL to 3.6V | 84 | ||
| Static output high level | VOH | 2.8 | 3.6 | V | 15kΩ RL to VSS | 84 | |
| Rise time | tr | 4 | 20 | ns | CL ≤ 50pF | 84 | |
| Fall time | tf | 4 | 20 | ns | CL ≤ 50pF | 84 | |
| Rise/fall time matching | trfm | 90 | 110 | % | tr / tf | 84 | |
| Output signal crossover voltage | VCRS | 1.3 | 2 | V | 84 | ||
| Output series matching resistor | Rs | 27 | 39 | Ohm | External matching resistor, placed close to chip pin | 85 | |
| ADC supply voltage | VDDA | 1.8 | 3.6 | V | 85 | ||
| ADC positive reference voltage | VREF+ | 1.8 | V | max = VDDA | 85 | ||
| ADC clock frequency | fADC | 72 | MHz | 85 | |||
| ADC sampling rate | fs | 5 | MHz | 85 | |||
| ADC conversion voltage range | VAIN | 0 | V | VSSA or VREF- connected to ground; max = VREF+ | 85 | ||
| ADC power-up time | tSTAB | 0 | 0 | 20 | μs | 85 | |
| ADC sampling time | tS | 1.5 | 239.5 | 1/fADC | 85 | ||
| ADC total conversion time including sampling | tCONV | 14 | 252 | 1/fADC | tS + successive approximation 12.5 | 85 | |
| ADC total unadjusted error | ET | -5 | 1.3 | 5 | LSB | fHCLK = fADC = 72 MHz, sample rate 1.75 Msps, VDDA = 3.3 V, TA = 25 °C, after calibration, VREF+ = VDDA | 85 |
| ADC offset error | EO | -2 | 1 | 2 | LSB | fHCLK = fADC = 72 MHz, sample rate 1.75 Msps, VDDA = 3.3 V, TA = 25 °C, after calibration, VREF+ = VDDA | 85 |
| ADC differential linearity error | ED | -1 | 0.7 | 1 | LSB | fHCLK = fADC = 72 MHz, sample rate 1.75 Msps, VDDA = 3.3 V, TA = 25 °C, after calibration, VREF+ = VDDA | 85 |
| ADC integral linearity error | EL | -2 | 0.8 | 2 | LSB | fHCLK = fADC = 72 MHz, sample rate 1.75 Msps, VDDA = 3.3 V, TA = 25 °C, after calibration, VREF+ = VDDA | 85 |
CAD (KiCad official)
- Symbol:
N32G452RCL7 - Footprint:
Package_QFP:LQFP-64_10x10mm_P0.5mm - 3D model: LQFP-64(10x10) (KiCad packages3D, STEP)
- 3D model files:
n32g452rcl7-etched.step/n32g452rcl7-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);n32g452rcl7.step/n32g452rcl7.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Nations Technologies Inc datasheet (96 pp, sha256
64263c0a0ef9dd52, retrieved 2026-10-28, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).