Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

MX35LF1GE4AB-Z4ITR

MXIC(Macronix) · NAND FLASH · WSON-8(6x8)

MX35LF1GE4AB-Z4ITR from MXIC(Macronix), in a WSON-8(6x8). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 CS# input Chip Select input for the serial NAND device (datasheet gives only the function, no electrical limits).
2 SO/SIO1 bidirectional Serial Data Output for 1 x I/O, and Serial Data Input & Output (SIO1) for 2xI/O or 4xI/O read mode.
3 WP#/SIO2 bidirectional Write protection: connect to GND, or Serial Data Input & Output (SIO2) for 4xI/O read mode.
4 GND power_in Ground.
5 SI/SIO0 bidirectional Serial Data Input for 1 x I/O, and Serial Data Input & Output (SIO0) for 2xI/O or 4xI/O read mode.
6 SCLK input Clock Input; data is latched on the rising edge of SCLK and shifts out on the falling edge (serial mode 0 / mode 3).
7 HOLD#/SIO3 bidirectional Hold, or Serial Data Input & Output (SIO3) for 4xI/O read mode.
8 VCC power_in +3V power supply; the ordering information gives the VCC range as 2.7V to 3.6V (voltage option L).
9 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer MXIC(Macronix)
Package WSON-8(6x8)
Category Memory
Pins 9

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input leakage current ILI -10 10 uA VIN= 0 to VCC Max. 44
Output leakage current ILO -10 10 uA VOUT= 0 to VCC Max. 44
VCC standby current (CMOS) ISB 15 50 uA VIN=VCC or GND, CS#=VCC 44
VCC active current (Sequential Read) ICC1 15 30 mA f=104MHz 44
VCC active current (Program) ICC2 15 30 mA 44
VCC active current (Erase) ICC3 15 30 mA 44
Input low level VIL -0.3 V 44
Output low voltage VOL 0.2 V IOL= -1mA 44
Input capacitance CIN 6 pF VIN = 0V; TA = +25°C, F = 1 MHz 43
Output capacitance COUT 8 pF VOUT = 0V; TA = +25°C, F = 1 MHz 43
Operating temperature range -40 85 °C Industrial grade 43
VCC supply voltage VCC 2.7 3.6 V Tolerance, +3.3V nominal 43
Temperature under bias -50 125 °C 43
Storage temperature -65 150 °C 43
All input voltages with respect to ground -0.6 4.6 V With respect to ground (Note 2) 43
VCC supply voltage with respect to ground VCC -0.6 4.6 V With respect to ground (Note 2) 43
ESD protection 2000 V Printed as '>2000V' 43
Pin overshoot below Vss -2 V Relative to Vss, up to 20ns during voltage transitions 43
Pin overshoot above VCC 2 V Relative to VCC, up to 20ns during voltage transitions 43
Clock Frequency fC 104 MHz 44
HOLD# high hold time relative to SCLK tCHHH 5 ns 44
HOLD# low hold time relative to SCLK tCHHL 5 ns 44
Command deselect time tCS 100 ns 44
Chip select hold time tCHSH 4 ns 44
Chip select setup time tSLCH 4 ns 44
Chip select non-active setup time tSHCH 4 ns 44
Chip select non-active hold time tCHSL 4 ns 44
Output disable time tDIS 20 ns 44
Hold# non-active setup time relative to SCLK tHC 5 ns 44
Hold# setup time relative to SCLK tHD 5 ns 44
Data input hold time tHDDAT 3.5 ns 44
Output hold time tHO 1 ns 44
Hold to output High-Z tHZ 15 ns 44
Hold to output low-Z tLZ 15 ns 44
Data input setup time tSUDAT 3.5 ns 44
Clock LOW to output Valid tV 8 ns 44
Clock HIGH time tWH 4 ns 44
Clock LOW time tWL 4 ns 44
WP# hold time tWPH 100 ns 44
WP# setup time tWPS 20 ns 44
Data transfer time from NAND Flash array to data register tRD 25 us 44
Dummy busy time for data read sequential (For 1Gb) tRCBSY 3.5 25 us 44
Data transfer time from NAND Flash array to data register with internal ECC enabled tRD_ECC 45 70 us 44
Page programming time tPROG 300 600 us 44
Page programming time under internal ECC enabled tPROG_ECC 320 600 us 44
Block Erase Time tERS 1 3.5 ms 44
Number of partial-page programming operation supported (NOP) NOP 4 cycle 44

CAD (KiCad official)

  • Symbol: MX35LF1GE4AB-Z4ITR
  • Footprint: Package_SON:WSON-8-1EP_8x6mm_P1.27mm_EP3.4x4.3mm
  • 3D model: WSON-8(6x8), generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 0.75 mm nominal WSON height). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions are nominal, not the manufacturer's CAD (STEP)
  • 3D model files: mx35lf1ge4ab-z4itr-etched.step / mx35lf1ge4ab-z4itr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); mx35lf1ge4ab-z4itr.step / mx35lf1ge4ab-z4itr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: MXIC(Macronix) datasheet (50 pp, sha256 68fb98eb328d80be, retrieved 2026-10-30, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF