Generated by kicad-footprint-generator · KiCad file format 20260206
MS7705
Hangzhou Ruimeng Tech · Analog To Digital Converters (ADCs) · SOP-16-300mil
MS7705 from Hangzhou Ruimeng Tech, in a SOP-16-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SCLK | input | Serial clock input with Schmitt-trigger logic used to access the serial data of the device, may be continuous or non-continuous. |
| 2 | MCLK IN | input | Master clock input from crystal/resonator or external CMOS-compatible clock, clock frequency range 500kHz to 5MHz. |
| 3 | MCLK OUT | output | Crystal/resonator connection to MCLK IN, provides an inverted clock when an external clock drives MCLK IN, and can be disabled with the CLKDIS bit; drives a CMOS load. |
| 4 | CS | input | Active-low chip select logic input selecting the device; may be used as frame sync signal in communication. |
| 5 | RESET | input | Active-low reset input that resets control logic, interface logic, calibration coefficients, digital filter and analog modulator to power-up state. |
| 6 | AIN2(+) | input | For MS7705 the positive input of differential analog input channel 2; for MS7706 the input of analog channel 1. |
| 7 | AIN1(+) | input | For MS7705 the positive input of differential analog input channel 1; for MS7706 the input of analog channel 2. |
| 8 | AIN1(-) | input | For MS7705 the negative input of differential analog input channel 1; for MS7706 the COMMON input to which analog channels 1, 2 and 3 are referenced. |
| 9 | REF IN(+) | input | Positive differential reference input which must be greater than REF IN(-) and may take any value between VDD and GND. |
| 10 | REF IN(-) | input | Negative differential reference input which may take any value between VDD and GND while remaining below REF IN(+). |
| 11 | AIN2(-) | input | For MS7705 the negative input of differential analog input channel 2; for MS7706 the input of analog channel 3. |
| 12 | DRDY | output | Logic output that goes low to indicate a new result is available in the data register and is also used to indicate completion of internal calibration. |
| 13 | DOUT | output | Serial data output from the internal output shift register, which can hold communication, clock or data register contents. |
| 14 | DIN | input | Serial data input into the internal input shift register, transferring data to setup, clock or communication registers. |
| 15 | VDD | power_in | Supply voltage of +2.7V to +5.25V. |
| 16 | GND | power_in | Ground reference point for the internal circuitry. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Hangzhou Ruimeng Tech |
| Package | SOP-16-300mil |
| Category | Data Converters |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Resolution, no missing codes | 16 | Bits | 5 | ||||
| Integral nonlinearity | -0.003 | 0.003 | %of FSR | 5 | |||
| Bipolar negative full-scale error | -0.003 | 0.003 | %of FSR | printed ±0.001 typ and ±0.003 max | 5 | ||
| Common-mode rejection ratio | CMR | 96 | dB | VDD=5V, gain=1 | 5 | ||
| Common-mode rejection ratio | CMR | 105 | dB | VDD=5V, gain=2 | 5 | ||
| Common-mode rejection ratio | CMR | 110 | dB | VDD=5V, gain=4 | 5 | ||
| Common-mode rejection ratio | CMR | 130 | dB | VDD=5V, gain=8 to 128 | 5 | ||
| Common-mode rejection ratio | CMR | 120 | dB | VDD=3V, gain=4 | 5 | ||
| 50Hz/60Hz notch rejection | 98 | dB | normal mode 50Hz, notch 25Hz,50Hz, ±0.02×fNOTCH | 5 | |||
| 50Hz/60Hz notch rejection | 150 | dB | normal mode 50Hz, notch 25Hz,50Hz, ±0.02×fNOTCH | 5 | |||
| Power supply voltage | VDD | -0.3 | 7 | V | 4 | ||
| Analog input pin voltage | VIN | -0.3 | V | maximum printed as VDD+0.3 | 4 | ||
| Reference input voltage | VREF | -0.3 | V | maximum printed as VDD+0.3 | 4 | ||
| Digital pin input voltage | VDIN | -0.3 | V | maximum printed as VDD+0.3 | 4 | ||
| Digital pin output voltage | VOUT | -0.3 | V | maximum printed as VDD+0.3 | 4 | ||
| Operating temperature range | TA | -40 | 85 | ℃ | 4 | ||
| Storage temperature range | Tstg | -65 | 150 | ℃ | 4 | ||
| Soldering temperature | 150 | ℃ | 4 | ||||
| Electrostatic protection (ESD) | 4000 | V | printed as >4000 | 4 | |||
| Supply voltage range | VDD | 2.7 | 5.25 | V | pin description: 2.7V to 5.25V | 3 |
CAD (KiCad official)
- Symbol:
MS7705 - Footprint:
Package_SO:SOIC-16W_7.5x10.3mm_P1.27mm - 3D model: SOP-16-300mil (KiCad packages3D, STEP)
- 3D model files:
ms7705-etched.step/ms7705-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ms7705.step/ms7705.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Hangzhou Ruimeng Tech datasheet, copy hosted by LCSC (42 pp, sha256
4c9f432ddb7fe9a4, retrieved 2026-11-20) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).