← Commit history
README.md+62−65
@@ -8,22 +8,22 @@ MS1242 from Hangzhou Ruimeng Tech, in a TSSOP-16. Pinout and pin descriptions ex  | Pin | Name | Type | Function | |---|---|---|---|-| 1 | VDD | power_in | Power supply pin; the datasheet gives an operating supply range of 2.7 V to 5.25 V. |-| 2 | XIN | input | Clock input per the pin table, used with an external crystal (10-20 pF capacitors on MCLK and XTAL) or an external clock. |-| 3 | XOUT | output | Clock output per the pin table; the clock generator section states an external clock is applied through this pin with XTAL left floating. |-| 4 | PDWN | input | Power-down control signal, active low. |-| 5 | VREF+ | power_in | Positive analog reference voltage input; the differential reference (REFP-REFN) must not exceed 2.5 V at VDD=5 V with RANGE=0, 5.0 V at VDD=5 V with RANGE=1, 1.25 V at VDD=3 V with RANGE=0, or 2.5 V at VDD=3 V with RANGE=1, and must not exceed VDD. |-| 6 | VREF- | power_in | Negative analog reference voltage input, forming the differential reference with VREF+ under the same limits as stated for the reference voltage. |-| 7 | AIN0/D0 | input | Analog input channel 0, which can also serve as data I/O pin D0 when configured via the IOCON, DIR and DIO registers; the power-up default is analog input. |-| 8 | AIN1/D1 | input | Analog input channel 1, which can also serve as data I/O pin D1 when configured via the IOCON, DIR and DIO registers; the power-up default is analog input. |-| 9 | AIN2/D2 | input | Analog input channel 2, which can also serve as data I/O pin D2 when configured via the IOCON, DIR and DIO registers; the power-up default is analog input. |-| 10 | AIN3/D3 | input | Analog input channel 3, which can also serve as data I/O pin D3 when configured via the IOCON, DIR and DIO registers; the power-up default is analog input. |+| 1 | VDD | power_in | Power supply pin; the datasheet gives an operating supply of 2.7 V to 5.25 V and an absolute maximum of -0.3 V to 6 V. |+| 2 | XIN | input | Clock input pin for the crystal or oscillator; the system clock fosc is specified at 1 MHz to 5 MHz, and 10 pF to 20 pF capacitors are required on MCLK and XTAL when a crystal is used. |+| 3 | XOUT | output | Clock output pin for the crystal; the datasheet also says an external clock is applied at this pin with XTAL left floating, which conflicts with the pin direction printed in the table. |+| 4 | PDWN | input | Power-down control input, active low. |+| 5 | VREF+ | power_in | Analog positive reference voltage input; the differential reference (REFP minus REFN) must not exceed 2.5 V at VDD=5 V with RANGE=0, or 1.25 V at VDD=3 V with RANGE=0, and must not exceed the supply voltage. |+| 6 | VREF- | power_in | Analog negative reference voltage input, forming the differential reference pair with VREF+ (REFN); the reference voltage must not exceed the supply voltage. |+| 7 | AIN0/D0 | bidirectional | Analog input channel 0, also usable as data I/O bit 0; the analog input must stay within -0.5 V to VDD+0.5 V absolute maximum. |+| 8 | AIN1/D1 | bidirectional | Analog input channel 1, also usable as data I/O bit 1; the analog input must stay within -0.5 V to VDD+0.5 V absolute maximum. |+| 9 | AIN2/D2 | bidirectional | Analog input channel 2, also usable as data I/O bit 2; the analog input must stay within -0.5 V to VDD+0.5 V absolute maximum. |+| 10 | AIN3/D3 | bidirectional | Analog input channel 3, also usable as data I/O bit 3; the analog input must stay within -0.5 V to VDD+0.5 V absolute maximum. | | 11 | GND | power_in | Ground reference pin. |-| 12 | CS | input | SPI chip select, active low; it must be held low for the whole communication, and when it goes high the SPI bus is reset. |-| 13 | DIN | input | SPI serial data input, sampled on SCLK edges. |-| 14 | DOUT | output | SPI serial data output (SDO), which is high impedance when not in use so that DIN and DOUT can be tied together on a bidirectional bus. |-| 15 | SCLK | input | SPI serial clock input with Schmitt-trigger input, used to sample SDI and SDO and required to be clean to avoid sampling errors. |-| 16 | DRDY | output | Data ready output, active low, which goes low when new conversion data is ready in the data output register. |+| 12 | CS | input | SPI chip select input, active low; it must be held low for the whole communication, and when it goes high the SPI bus is reset. |+| 13 | DIN | input | SPI serial data input. |+| 14 | DOUT | output | SPI serial data output; it is high impedance when not in use, allowing SDI and SDO to be tied together on a bidirectional bus. |+| 15 | SCLK | input | SPI serial clock input with Schmitt-trigger input, used to sample SDI and SDO; it must be free of noise to avoid erroneous sampling. |+| 16 | DRDY | output | Data-ready output, active low; it goes low when new conversion data is available in the data output register. |  ## Key specifications @@ -40,66 +40,63 @@ Limits as printed in the datasheet (page.json `metadata.characteristics` carries  | Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page | |---|---|---|---|---|---|---|---|-| Supply voltage | VDD | -0.3 |  | 6 | V |  | 5 |-| Input current, instantaneous | Iin |  |  | 100 | mA |  | 5 |-| Input current, continuous | Iin |  |  | 10 | mA |  | 5 |-| Analog input voltage (Ain) | Ain | -0.5 |  |  | V | max = VDD+0.5 | 5 |-| Digital input voltage (Din) | Din | -0.3 |  |  | V | max = VDD+0.3 | 5 |-| Digital output voltage (Dout) | Dout | -0.3 |  |  | V | max = VDD+0.3 | 5 |+| Supply voltage (absolute maximum) | VDD | -0.3 |  | 6 | V |  | 5 |+| Input current, instantaneous | Iin |  |  | 100 | mA | 瞬时 (instantaneous) | 5 |+| Input current, continuous | Iin |  |  | 10 | mA | 连续 (continuous) | 5 |+| Analog input voltage (lower limit; upper limit printed as VDD+0.5) | Ain | -0.5 |  |  | V |  | 5 |+| Digital input voltage (lower limit; upper limit printed as VDD+0.3) | Din | -0.3 |  |  | V |  | 5 |+| Digital output voltage (lower limit; upper limit printed as VDD+0.3) | Dout | -0.3 |  |  | V |  | 5 | | Maximum junction temperature | Jt |  |  | 150 | C |  | 5 |-| Operating temperature | TA | -40 |  | 85 | C |  | 5 |-| Storage temperature | Tstg | -60 |  | 100 | C |  | 5 |-| Master clock frequency (digital characteristics, VDD 2.7V to 5.25V) | fosc | 1 |  | 5 | MHz |  | 5 |-| Master clock period (digital characteristics, VDD 2.7V to 5.25V) | Tosc | 200 |  | 1000 | ns | 1/fOSC | 5 |-| Digital input high-level leakage current (VDD 2.7V to 5.25V) |  |  |  | 10 | uA |  | 5 |-| Digital input low-level leakage current (VDD 2.7V to 5.25V) |  | -10 |  |  | uA |  | 5 |-| Operating supply voltage | VDD | 2.7 |  | 5.25 | V |  | 1 |-| External differential reference voltage, maximum (VDD=5V, RANGE = 0) | REF |  |  | 2.5 | V | VDD=5V, RANGE = 0; must not exceed | 13 |-| External differential reference voltage, maximum (VDD=5V, RANGE = 1) | REF |  |  | 5 | V | VDD=5V, RANGE = 1; must not exceed | 13 |-| External differential reference voltage, maximum (VDD=3V, RANGE = 0) | REF |  |  | 1.25 | V | VDD=3V, RANGE = 0; must not exceed | 13 |-| External differential reference voltage, maximum (VDD=3V, RANGE = 1) | REF |  |  | 2.5 | V | VDD=3V, RANGE = 1; must not exceed | 13 |-| Minimum supply ramp rate |  | 1 |  |  | V/10ms | supply voltage must rise monotonically | 15 |-| Load capacitors on MCLK and XTAL pins (crystal operation) |  | 10 |  | 20 | pF | external crystal circuit | 13 |-| PGA programmable gain range (VDD=5V table) |  | 1 |  | 128 |  |  | 6 |-| Integral nonlinearity (VDD=5V table) |  | -0.0015 |  | 0.0015 | % of FS |  | 6 |-| Reference voltage REF=REFP-REFN (VDD=5V table) | REF | 0.1 | 2.5 | 2.6 | V | RANGE = 0 | 6 |-| Reference voltage REF=REFP-REFN (VDD=5V table) | REF | 0.1 |  |  | V | RANGE = 1; max = VDD | 6 |-| Offset DAC gain error (VDD=5V table) |  | -10 |  | 10 | % |  | 7 |-| Supply voltage VDD (VDD=5V table) | VDD | 4.75 |  | 5.25 | V |  | 7 |-| Supply current (VDD=5V table) |  |  | 240 | 375 | uA | PGA = 1, Buffer off | 7 |-| Supply current (VDD=5V table) |  |  | 450 | 800 | uA | PGA = 128, Buffer off | 7 |-| Supply current (VDD=5V table) |  |  | 290 | 425 | uA | PGA = 1, Buffer on | 7 |-| Supply current (VDD=5V table) |  |  | 960 | 1400 | uA | PGA = 128, Buffer on | 7 |-| Power dissipation (VDD=5V table) |  |  | 1.2 | 1.9 | mW | PGA = 1, Buffer off | 7 |-| Operating temperature range (electrical table) |  | -40 |  | 85 | C |  | 7 |-| Storage temperature range (electrical table) |  | -60 |  | 100 | C |  | 7 |-| PGA programmable gain range (VDD=3V table) |  | 1 |  | 128 |  |  | 8 |-| Integral nonlinearity (VDD=3V table) |  | -0.0015 |  | 0.0015 | % of FS |  | 8 |-| Reference voltage REF=REFP-REFN (VDD=3V table) | REF | 0.1 | 1.25 | 1.26 | V | RANGE = 0 | 8 |-| Reference voltage REF=REFP-REFN (VDD=3V table) | REF | 0.1 | 2.5 | 2.6 | V | RANGE = 1 | 8 |-| Offset DAC gain error (VDD=3V table) |  | -10 |  | 10 | % |  | 9 |-| Supply voltage VDD (VDD=3V table) | VDD | 2.7 |  | 3.3 | V |  | 9 |-| Supply current (VDD=3V table) |  |  | 190 | 375 | uA | PGA = 1, Buffer off | 9 |-| Supply current (VDD=3V table) |  |  | 460 | 700 | uA | PGA = 128, Buffer off | 9 |-| Supply current (VDD=3V table) |  |  | 240 | 375 | uA | PGA = 1, Buffer on | 9 |-| Supply current (VDD=3V table) |  |  | 870 | 1325 | uA | PGA = 128, Buffer on | 9 |-| Power dissipation (VDD=3V table) |  |  | 0.6 | 1.2 | mW | PGA = 1, Buffer off | 9 |-| SCLK clock period | t1 | 4 |  |  | tosc 周期 |  | 10 |+| Operating temperature range | TA | -40 |  | 85 | C |  | 5 |+| Storage temperature range | Tstg | -60 |  | 100 | C |  | 5 |+| Digital input high-level leakage current | IIH |  |  | 10 | uA |  | 5 |+| Digital input low-level leakage current | IIL | -10 |  |  | uA |  | 5 |+| Master clock frequency | fosc | 1 |  | 5 | MHz |  | 5 |+| Master clock period | Tosc | 200 |  | 1000 | ns | 1/fOSC | 5 |+| PGA selectable gain range | PGA | 1 |  | 128 |  | VDD=+5V | 6 |+| Integral nonlinearity | INL | -0.0015 |  | 0.0015 | % of FS | VDD=+5V | 6 |+| Power supply rejection ratio, DC | PSRR | 80 |  | 95 | dB | VDD=+5V; DC | 6 |+| Reference voltage (REF = REFP - REFN) | VREF | 0.1 | 2.5 | 2.6 | V | VDD=+5V; RANGE = 0 | 6 |+| Reference voltage (REF = REFP - REFN), upper limit printed as VDD | VREF | 0.1 |  |  | V | VDD=+5V; RANGE = 1 | 6 |+| REFP, REFN input range (lower limit; upper limit printed as VDD) | REFP, REFN | 0 |  |  | V | VDD=+5V; RANGE = 0 | 6 |+| Offset DAC gain error |  | -10 |  | 10 | % | VDD=+5V | 7 |+| Supply voltage | VDD | 4.75 |  | 5.25 | V | VDD=+5V | 7 |+| Supply current |  | 240 |  | 375 | uA | VDD=+5V; PGA = 1, Buffer 关闭 (off) | 7 |+| Supply current |  | 450 |  | 800 | uA | VDD=+5V; PGA = 128, Buffer 关闭 (off) | 7 |+| Supply current |  | 290 |  | 425 | uA | VDD=+5V; PGA = 1, Buffer 打开 (on) | 7 |+| Supply current |  | 960 |  | 1400 | uA | VDD=+5V; PGA = 128, Buffer 打开 (on) | 7 |+| Power dissipation |  | 1.2 |  | 1.9 | mW | VDD=+5V; PGA = 1, Buffer 关闭 (off) | 7 |+| Integral nonlinearity | INL | -0.0015 |  | 0.0015 | % of FS | VDD=+3V | 8 |+| Power supply rejection ratio, DC | PSRR | 75 |  | 90 | dB | VDD=+3V; DC | 8 |+| Reference voltage (REF = REFP - REFN) | VREF | 0.1 | 1.25 | 1.26 | V | VDD=+3V; RANGE = 0 | 8 |+| Reference voltage (REF = REFP - REFN) | VREF | 0.1 | 2.5 | 2.6 | V | VDD=+3V; RANGE = 1 | 8 |+| REFP, REFN input range (lower limit; upper limit printed as VDD) | REFP, REFN | 0 |  |  | V | VDD=+3V; RANGE = 0 | 8 |+| Offset DAC gain error |  | -10 |  | 10 | % | VDD=+3V | 9 |+| Supply voltage | VDD | 2.7 |  | 3.3 | V | VDD=+3V | 9 |+| Supply current |  | 190 |  | 375 | uA | VDD=+3V; PGA = 1, Buffer 关闭 (off) | 9 |+| Supply current |  | 460 |  | 700 | uA | VDD=+3V; PGA = 128, Buffer 关闭 (off) | 9 |+| Supply current |  | 240 |  | 375 | uA | VDD=+3V; PGA = 1, Buffer 打开 (on) | 9 |+| Supply current |  | 870 |  | 1325 | uA | VDD=+3V; PGA = 128, Buffer 打开 (on) | 9 |+| Power dissipation |  | 0.6 |  | 1.2 | mW | VDD=+3V; PGA = 1, Buffer 关闭 (off) | 9 |+| Conversion-to-input timing: SCLK clock period (minimum) | t1 | 4 |  |  | tosc 周期 | SCLK 时钟周期 | 10 |+| SCLK clock period (maximum, DRDY periods) | t1 |  |  | 3 | DRDY 周期 | SCLK 时钟周期 | 10 | | SCLK pulse width, high and low | t2 | 200 |  |  | ns |  | 10 | | CS falling edge to first SCLK edge setup time | t3 | 0 |  |  | ns |  | 10 | | DIN data setup time | t4 | 50 |  |  | ns |  | 10 | | DIN data hold time | t5 | 50 |  |  | ns |  | 10 | | Last SDI SCLK edge to first SDO SCLK edge | t6 | 50 |  |  | tosc 周期 | RDATA, RDATAC, RREG, WREG | 10 | | SDO output data delay from SCLK | t7 |  |  | 50 | ns |  | 10 |+| SDO data hold time | t8 | 0 |  |  | ns |  | 10 | | SDO tri-state delay from SCLK edge | t9 | 6 |  | 10 | tosc 周期 |  | 10 |-| Last SCLK edge of current command to first SCLK edge of next command | t11 | 4 |  |  | tosc 周期 | RREG, WREG, SYNC, SLEEP, RDATA, RDATAC, STOPC | 10 |-| Last SCLK edge of current command to first SCLK edge of next command | t11 | 8 |  |  | DRDY 周期 | OCALSYS, GCALSYS | 11 |-| Last SCLK edge of current command to first SCLK edge of next command | t11 | 16 |  |  | tosc 周期 | RESET | 11 |+| CS hold time after last SCLK edge | t10 | 0 |  |  | ns |  | 10 |+| Last SCLK edge of current command to first SCLK edge of next command | t11 | 4 |  |  | tosc 周期 | RREG, WREG, SYNC, SLEEP, RDATA, RDATAC, STOPC | 11 |+| Last SCLK edge to first SCLK edge of next command |  | 8 |  |  | DRDY 周期 | OCALSYS, GCALSYS | 11 |+| RESET command timing |  | 16 |  |  | tosc 周期 | RESET | 11 | | Pulse width | t16 | 4 |  |  | tosc 周期 |  | 11 | | Allowed analog input change to next valid conversion | t17 | 5000 |  |  | tosc 周期 |  | 11 | | DOR update, DOR invalid | t18 | 4 |  |  | tosc 周期 |  | 11 |-| DRDY low to first SCLK edge | t19 | 10 |  |  | tosc 周期 | RDATAC mode | 11 |-| DRDY low to first SCLK edge | t19 | 0 |  |  | tosc 周期 | other modes | 11 |+| First SCLK after DRDY falls | t19 | 10 |  |  | tosc 周期 | RDATAC 模式 (RDATAC mode) | 11 |+| First SCLK after DRDY falls | t16 | 0 |  |  | tosc 周期 | 其他模式 (other modes) | 11 |  ## CAD (KiCad official) @@ -112,7 +109,7 @@ Limits as printed in the datasheet (page.json `metadata.characteristics` carries  Data extracted from the manufacturer datasheet, not a distributor listing: -- **Datasheet:** [Hangzhou Ruimeng Tech datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588885031205154816) (27 pp, sha256 `150cce2e87cea6bc`, retrieved 2026-11-10, tier: lcsc)+- **Datasheet:** [Hangzhou Ruimeng Tech datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588885031205154816) (27 pp, sha256 `150cce2e87cea6bc`, retrieved 2026-11-11, tier: lcsc) - **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original. - **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - **CAD:** KiCad official libraries (CC-BY-SA 4.0).
ms1242-hero.overlay.json+436−434
@@ -1,436 +1,438 @@ {-  "spec": "adom-hero 1.4",-  "mpn": "MS1242",-  "kind": "component + footprint reference art",-  "board_use": false,-  "plane_z_mm": -0.02,-  "units": "metre",-  "upAxis": "Z",-  "layers": {-    "pad_outlines": {-      "material": "Footprint pads - teal dashed outlines - 50 percent opacity",-      "rgba": [-        0.0,-        0.902,-        0.863,-        0.5-      ],-      "pads": 16,-      "span_mm": 7.2,-      "dash_mm": 0.18,-      "gap_mm": 0.108,-      "pad_stroke_mm": 0.0432-    },-    "silkscreen": {-      "material": "Silkscreen reference lines - 30 percent opacity",-      "rgba": [-        0.92,-        0.96,-        1.0,-        0.3-      ],-      "footprint_items": 3,-      "pin1": {-        "source": "footprint silkscreen",-        "pad": "1"-      }-    },-    "signal_names": {-      "material": "Signal names - 50 percent opacity",-      "rgba": [-        0.92,-        0.96,-        1.0,-        0.5-      ],-      "font": "DejaVu Sans Mono",-      "labels": 16,-      "sides": "top + mirrored underside (single-sided)",-      "fallback_to_pad_number": 0-    }-  },-  "align": {-    "ok": true,-    "centre_offset_mm": 0.0,-    "tolerance_mm": 0.576,-    "orientation_flipped": false,-    "contacts_bbox_mm": [-      -3.2,-      3.2,-      -2.405,-      2.405-    ],-    "pads_bbox_mm": [-      -3.6,-      3.6,-      -2.475,-      2.475-    ],-    "seating_z_mm": -0.0-  },-  "sources": {-    "glb": "ms1242-etched.glb",-    "glb_sha256": "2eee6dc9c7e050def47ca49ea4d10af1f79853f2d8eea3aadee3fda5af4223d7",-    "footprint": "ms1242.kicad_mod",-    "footprint_sha256": "fbac79fc5f310754726589d67071a422c429216f843ecd6013bbe2e6a49e7064",-    "pins": "page.json component.pins",-    "pins_sha256": "118622cc95189aee3415ecb2c36ebce9c46c8f898f6092939fe5eb7bf079eddb"-  },-  "generator": "adom-wiki 1.8.15 (component_hero)",-  "labels": [-    {-      "pad": "1",-      "text": "VDD",-      "x": -4.29,-      "y": -2.275,-      "align": "right",-      "vertical": false,-      "h": 0.325-    },-    {-      "pad": "2",-      "text": "XIN",-      "x": -3.7,-      "y": -1.625,-      "align": "right",-      "vertical": false,-      "h": 0.325-    },-    {-      "pad": "3",-      "text": "XOUT",-      "x": -3.7,-      "y": -0.975,-      "align": "right",-      "vertical": false,-      "h": 0.325-    },-    {-      "pad": "4",-      "text": "PDWN",-      "x": -3.7,-      "y": -0.325,-      "align": "right",-      "vertical": false,-      "h": 0.325-    },-    {-      "pad": "5",-      "text": "VREF+",-      "x": -3.7,-      "y": 0.325,-      "align": "right",-      "vertical": false,-      "h": 0.325-    },-    {-      "pad": "6",-      "text": "VREF–",-      "x": -3.7,-      "y": 0.975,-      "align": "right",-      "vertical": false,-      "h": 0.325-    },-    {-      "pad": "7",-      "text": "AIN0/D0",-      "x": -3.7,-      "y": 1.625,-      "align": "right",-      "vertical": false,-      "h": 0.325-    },-    {-      "pad": "8",-      "text": "AIN1/D1",-      "x": -3.7,-      "y": 2.275,-      "align": "right",-      "vertical": false,-      "h": 0.325-    },-    {-      "pad": "9",-      "text": "AIN2/D2",-      "x": 3.7,-      "y": 2.275,-      "align": "left",-      "vertical": false,-      "h": 0.325-    },-    {-      "pad": "10",-      "text": "AIN3/D3",-      "x": 3.7,-      "y": 1.625,-      "align": "left",-      "vertical": false,-      "h": 0.325-    },-    {-      "pad": "11",-      "text": "GND",-      "x": 3.7,-      "y": 0.975,-      "align": "left",-      "vertical": false,-      "h": 0.325-    },-    {-      "pad": "12",-      "text": "CS",-      "x": 3.7,-      "y": 0.325,-      "align": "left",-      "vertical": false,-      "h": 0.325-    },-    {-      "pad": "13",-      "text": "DIN",-      "x": 3.7,-      "y": -0.325,-      "align": "left",-      "vertical": false,-      "h": 0.325-    },-    {-      "pad": "14",-      "text": "DOUT",-      "x": 3.7,-      "y": -0.975,-      "align": "left",-      "vertical": false,-      "h": 0.325-    },-    {-      "pad": "15",-      "text": "SCLK",-      "x": 3.7,-      "y": -1.625,-      "align": "left",-      "vertical": false,-      "h": 0.325-    },-    {-      "pad": "16",-      "text": "DRDY",-      "x": 3.7,-      "y": -2.275,-      "align": "left",-      "vertical": false,-      "h": 0.325-    }+ "spec": "adom-hero 1.4",+ "mpn": "MS1242",+ "kind": "component + footprint reference art",+ "board_use": false,+ "plane_z_mm": -0.02,+ "units": "metre",+ "upAxis": "Z",+ "layers": {+  "pad_outlines": {+   "material": "Footprint pads - teal dashed outlines - 50 percent opacity",+   "rgba": [+    0.0,+    0.902,+    0.863,+    0.5+   ],+   "pads": 16,+   "span_mm": 7.2,+   "dash_mm": 0.18,+   "gap_mm": 0.108,+   "pad_stroke_mm": 0.0432+  },+  "silkscreen": {+   "material": "Silkscreen reference lines - 30 percent opacity",+   "rgba": [+    0.92,+    0.96,+    1.0,+    0.3+   ],+   "footprint_items": 3,+   "pin1": {+    "source": "footprint silkscreen",+    "pad": "1"+   }+  },+  "signal_names": {+   "material": "Signal names - 50 percent opacity",+   "rgba": [+    0.92,+    0.96,+    1.0,+    0.5+   ],+   "font": "DejaVu Sans Mono",+   "labels": 16,+   "sides": "top + mirrored underside (single-sided)",+   "omitted": null,+   "fallback_to_pad_number": 0+  }+ },+ "align": {+  "ok": true,+  "centre_offset_mm": 0.0,+  "over_pads": true,+  "tolerance_mm": 0.576,+  "orientation_flipped": false,+  "contacts_bbox_mm": [+   -3.2,+   3.2,+   -2.405,+   2.405+  ],+  "pads_bbox_mm": [+   -3.6,+   3.6,+   -2.475,+   2.475   ],-  "pads": [-    {-      "number": "1",-      "shape": "roundrect",-      "center_mm": [-        -2.8625,-        -2.275-      ],-      "size_mm": [-        1.475,-        0.4-      ],-      "rot": 0.0-    },-    {-      "number": "2",-      "shape": "roundrect",-      "center_mm": [-        -2.8625,-        -1.625-      ],-      "size_mm": [-        1.475,-        0.4-      ],-      "rot": 0.0-    },-    {-      "number": "3",-      "shape": "roundrect",-      "center_mm": [-        -2.8625,-        -0.975-      ],-      "size_mm": [-        1.475,-        0.4-      ],-      "rot": 0.0-    },-    {-      "number": "4",-      "shape": "roundrect",-      "center_mm": [-        -2.8625,-        -0.325-      ],-      "size_mm": [-        1.475,-        0.4-      ],-      "rot": 0.0-    },-    {-      "number": "5",-      "shape": "roundrect",-      "center_mm": [-        -2.8625,-        0.325-      ],-      "size_mm": [-        1.475,-        0.4-      ],-      "rot": 0.0-    },-    {-      "number": "6",-      "shape": "roundrect",-      "center_mm": [-        -2.8625,-        0.975-      ],-      "size_mm": [-        1.475,-        0.4-      ],-      "rot": 0.0-    },-    {-      "number": "7",-      "shape": "roundrect",-      "center_mm": [-        -2.8625,-        1.625-      ],-      "size_mm": [-        1.475,-        0.4-      ],-      "rot": 0.0-    },-    {-      "number": "8",-      "shape": "roundrect",-      "center_mm": [-        -2.8625,-        2.275-      ],-      "size_mm": [-        1.475,-        0.4-      ],-      "rot": 0.0-    },-    {-      "number": "9",-      "shape": "roundrect",-      "center_mm": [-        2.8625,-        2.275-      ],-      "size_mm": [-        1.475,-        0.4-      ],-      "rot": 0.0-    },-    {-      "number": "10",-      "shape": "roundrect",-      "center_mm": [-        2.8625,-        1.625-      ],-      "size_mm": [-        1.475,-        0.4-      ],-      "rot": 0.0-    },-    {-      "number": "11",-      "shape": "roundrect",-      "center_mm": [-        2.8625,-        0.975-      ],-      "size_mm": [-        1.475,-        0.4-      ],-      "rot": 0.0-    },-    {-      "number": "12",-      "shape": "roundrect",-      "center_mm": [-        2.8625,-        0.325-      ],-      "size_mm": [-        1.475,-        0.4-      ],-      "rot": 0.0-    },-    {-      "number": "13",-      "shape": "roundrect",-      "center_mm": [-        2.8625,-        -0.325-      ],-      "size_mm": [-        1.475,-        0.4-      ],-      "rot": 0.0-    },-    {-      "number": "14",-      "shape": "roundrect",-      "center_mm": [-        2.8625,-        -0.975-      ],-      "size_mm": [-        1.475,-        0.4-      ],-      "rot": 0.0-    },-    {-      "number": "15",-      "shape": "roundrect",-      "center_mm": [-        2.8625,-        -1.625-      ],-      "size_mm": [-        1.475,-        0.4-      ],-      "rot": 0.0-    },-    {-      "number": "16",-      "shape": "roundrect",-      "center_mm": [-        2.8625,-        -2.275-      ],-      "size_mm": [-        1.475,-        0.4-      ],-      "rot": 0.0-    }-  ]-}+  "seating_z_mm": -0.0+ },+ "sources": {+  "glb": "ms1242-etched.glb",+  "glb_sha256": "2eee6dc9c7e050def47ca49ea4d10af1f79853f2d8eea3aadee3fda5af4223d7",+  "footprint": "ms1242.kicad_mod",+  "footprint_sha256": "fbac79fc5f310754726589d67071a422c429216f843ecd6013bbe2e6a49e7064",+  "pins": "page.json component.pins",+  "pins_sha256": "118622cc95189aee3415ecb2c36ebce9c46c8f898f6092939fe5eb7bf079eddb"+ },+ "generator": "factory/hero_glb.py",+ "labels": [+  {+   "pad": "1",+   "text": "VDD",+   "x": -4.29,+   "y": -2.275,+   "align": "right",+   "vertical": false,+   "h": 0.325+  },+  {+   "pad": "2",+   "text": "XIN",+   "x": -3.7,+   "y": -1.625,+   "align": "right",+   "vertical": false,+   "h": 0.325+  },+  {+   "pad": "3",+   "text": "XOUT",+   "x": -3.7,+   "y": -0.975,+   "align": "right",+   "vertical": false,+   "h": 0.325+  },+  {+   "pad": "4",+   "text": "PDWN",+   "x": -3.7,+   "y": -0.325,+   "align": "right",+   "vertical": false,+   "h": 0.325+  },+  {+   "pad": "5",+   "text": "VREF+",+   "x": -3.7,+   "y": 0.325,+   "align": "right",+   "vertical": false,+   "h": 0.325+  },+  {+   "pad": "6",+   "text": "VREF\u2013",+   "x": -3.7,+   "y": 0.975,+   "align": "right",+   "vertical": false,+   "h": 0.325+  },+  {+   "pad": "7",+   "text": "AIN0/D0",+   "x": -3.7,+   "y": 1.625,+   "align": "right",+   "vertical": false,+   "h": 0.325+  },+  {+   "pad": "8",+   "text": "AIN1/D1",+   "x": -3.7,+   "y": 2.275,+   "align": "right",+   "vertical": false,+   "h": 0.325+  },+  {+   "pad": "9",+   "text": "AIN2/D2",+   "x": 3.7,+   "y": 2.275,+   "align": "left",+   "vertical": false,+   "h": 0.325+  },+  {+   "pad": "10",+   "text": "AIN3/D3",+   "x": 3.7,+   "y": 1.625,+   "align": "left",+   "vertical": false,+   "h": 0.325+  },+  {+   "pad": "11",+   "text": "GND",+   "x": 3.7,+   "y": 0.975,+   "align": "left",+   "vertical": false,+   "h": 0.325+  },+  {+   "pad": "12",+   "text": "CS",+   "x": 3.7,+   "y": 0.325,+   "align": "left",+   "vertical": false,+   "h": 0.325+  },+  {+   "pad": "13",+   "text": "DIN",+   "x": 3.7,+   "y": -0.325,+   "align": "left",+   "vertical": false,+   "h": 0.325+  },+  {+   "pad": "14",+   "text": "DOUT",+   "x": 3.7,+   "y": -0.975,+   "align": "left",+   "vertical": false,+   "h": 0.325+  },+  {+   "pad": "15",+   "text": "SCLK",+   "x": 3.7,+   "y": -1.625,+   "align": "left",+   "vertical": false,+   "h": 0.325+  },+  {+   "pad": "16",+   "text": "DRDY",+   "x": 3.7,+   "y": -2.275,+   "align": "left",+   "vertical": false,+   "h": 0.325+  }+ ],+ "pads": [+  {+   "number": "1",+   "shape": "roundrect",+   "center_mm": [+    -2.8625,+    -2.275+   ],+   "size_mm": [+    1.475,+    0.4+   ],+   "rot": 0.0+  },+  {+   "number": "2",+   "shape": "roundrect",+   "center_mm": [+    -2.8625,+    -1.625+   ],+   "size_mm": [+    1.475,+    0.4+   ],+   "rot": 0.0+  },+  {+   "number": "3",+   "shape": "roundrect",+   "center_mm": [+    -2.8625,+    -0.975+   ],+   "size_mm": [+    1.475,+    0.4+   ],+   "rot": 0.0+  },+  {+   "number": "4",+   "shape": "roundrect",+   "center_mm": [+    -2.8625,+    -0.325+   ],+   "size_mm": [+    1.475,+    0.4+   ],+   "rot": 0.0+  },+  {+   "number": "5",+   "shape": "roundrect",+   "center_mm": [+    -2.8625,+    0.325+   ],+   "size_mm": [+    1.475,+    0.4+   ],+   "rot": 0.0+  },+  {+   "number": "6",+   "shape": "roundrect",+   "center_mm": [+    -2.8625,+    0.975+   ],+   "size_mm": [+    1.475,+    0.4+   ],+   "rot": 0.0+  },+  {+   "number": "7",+   "shape": "roundrect",+   "center_mm": [+    -2.8625,+    1.625+   ],+   "size_mm": [+    1.475,+    0.4+   ],+   "rot": 0.0+  },+  {+   "number": "8",+   "shape": "roundrect",+   "center_mm": [+    -2.8625,+    2.275+   ],+   "size_mm": [+    1.475,+    0.4+   ],+   "rot": 0.0+  },+  {+   "number": "9",+   "shape": "roundrect",+   "center_mm": [+    2.8625,+    2.275+   ],+   "size_mm": [+    1.475,+    0.4+   ],+   "rot": 0.0+  },+  {+   "number": "10",+   "shape": "roundrect",+   "center_mm": [+    2.8625,+    1.625+   ],+   "size_mm": [+    1.475,+    0.4+   ],+   "rot": 0.0+  },+  {+   "number": "11",+   "shape": "roundrect",+   "center_mm": [+    2.8625,+    0.975+   ],+   "size_mm": [+    1.475,+    0.4+   ],+   "rot": 0.0+  },+  {+   "number": "12",+   "shape": "roundrect",+   "center_mm": [+    2.8625,+    0.325+   ],+   "size_mm": [+    1.475,+    0.4+   ],+   "rot": 0.0+  },+  {+   "number": "13",+   "shape": "roundrect",+   "center_mm": [+    2.8625,+    -0.325+   ],+   "size_mm": [+    1.475,+    0.4+   ],+   "rot": 0.0+  },+  {+   "number": "14",+   "shape": "roundrect",+   "center_mm": [+    2.8625,+    -0.975+   ],+   "size_mm": [+    1.475,+    0.4+   ],+   "rot": 0.0+  },+  {+   "number": "15",+   "shape": "roundrect",+   "center_mm": [+    2.8625,+    -1.625+   ],+   "size_mm": [+    1.475,+    0.4+   ],+   "rot": 0.0+  },+  {+   "number": "16",+   "shape": "roundrect",+   "center_mm": [+    2.8625,+    -2.275+   ],+   "size_mm": [+    1.475,+    0.4+   ],+   "rot": 0.0+  }+ ]+}\ No newline at end of file
ms1242.kicad_sym+4−4
@@ -32,11 +32,11 @@       (name "VREF–" (effects (font (size 1.27 1.27))))       (number "6" (effects (font (size 1.27 1.27))))     )-    (pin input line (at -17.78 -7.62 0) (length 5.08)+    (pin bidirectional line (at -17.78 -7.62 0) (length 5.08)       (name "AIN0/D0" (effects (font (size 1.27 1.27))))       (number "7" (effects (font (size 1.27 1.27))))     )-    (pin input line (at -17.78 -10.16 0) (length 5.08)+    (pin bidirectional line (at -17.78 -10.16 0) (length 5.08)       (name "AIN1/D1" (effects (font (size 1.27 1.27))))       (number "8" (effects (font (size 1.27 1.27))))     )@@ -64,11 +64,11 @@       (name "GND" (effects (font (size 1.27 1.27))))       (number "11" (effects (font (size 1.27 1.27))))     )-    (pin input line (at 17.78 -7.62 180) (length 5.08)+    (pin bidirectional line (at 17.78 -7.62 180) (length 5.08)       (name "AIN3/D3" (effects (font (size 1.27 1.27))))       (number "10" (effects (font (size 1.27 1.27))))     )-    (pin input line (at 17.78 -10.16 180) (length 5.08)+    (pin bidirectional line (at 17.78 -10.16 180) (length 5.08)       (name "AIN2/D2" (effects (font (size 1.27 1.27))))       (number "9" (effects (font (size 1.27 1.27))))     )
ms1242.lbr+16−7
@@ -50,7 +50,7 @@ <layer number="98" name="Guide" color="6" fill="1" visible="yes" active="yes"/> </layers> <library>-<description></description>+<description>Hangzhou Ruimeng Tech Analog To Digital Converters (ADC), TSSOP-16. Pinout cross-checked by two models against the datasheet</description> <packages> <package name="TSSOP-16_4.4x5mm_P0.65mm">   <description>TSSOP-16, 4.4 x 5 mm, 0.65 mm pitch</description>@@ -90,6 +90,7 @@ </packages> <symbols> <symbol name="MS1242">+  <description>Hangzhou Ruimeng Tech Analog To Digital Converters (ADC), TSSOP-16. Pinout cross-checked by two models against the datasheet</description>   <wire x1="-12.7" y1="10.16" x2="12.7" y2="10.16" width="0.254" layer="94"/>   <wire x1="12.7" y1="10.16" x2="12.7" y2="-12.7" width="0.254" layer="94"/>   <wire x1="12.7" y1="-12.7" x2="-12.7" y2="-12.7" width="0.254" layer="94"/>@@ -102,21 +103,21 @@   <pin name="PDWN" x="-17.78" y="0" length="middle" direction="in"/>   <pin name="VREF+" x="-17.78" y="-2.54" length="middle" direction="pwr"/>   <pin name="VREF" x="-17.78" y="-5.08" length="middle" direction="pwr"/>-  <pin name="AIN0/D0" x="-17.78" y="-7.62" length="middle" direction="in"/>-  <pin name="AIN1/D1" x="-17.78" y="-10.16" length="middle" direction="in"/>+  <pin name="AIN0/D0" x="-17.78" y="-7.62" length="middle" direction="io"/>+  <pin name="AIN1/D1" x="-17.78" y="-10.16" length="middle" direction="io"/>   <pin name="DRDY" x="17.78" y="7.62" length="middle" direction="out" rot="R180"/>   <pin name="SCLK" x="17.78" y="5.08" length="middle" direction="in" rot="R180"/>   <pin name="DOUT" x="17.78" y="2.54" length="middle" direction="out" rot="R180"/>   <pin name="DIN" x="17.78" y="0" length="middle" direction="in" rot="R180"/>   <pin name="CS" x="17.78" y="-2.54" length="middle" direction="in" rot="R180"/>   <pin name="GND" x="17.78" y="-5.08" length="middle" direction="pwr" rot="R180"/>-  <pin name="AIN3/D3" x="17.78" y="-7.62" length="middle" direction="in" rot="R180"/>-  <pin name="AIN2/D2" x="17.78" y="-10.16" length="middle" direction="in" rot="R180"/>+  <pin name="AIN3/D3" x="17.78" y="-7.62" length="middle" direction="io" rot="R180"/>+  <pin name="AIN2/D2" x="17.78" y="-10.16" length="middle" direction="io" rot="R180"/> </symbol> </symbols> <devicesets> <deviceset name="MS1242" prefix="U">-  <description></description>+  <description>Hangzhou Ruimeng Tech Analog To Digital Converters (ADC), TSSOP-16. Pinout cross-checked by two models against the datasheet</description>   <gates>     <gate name="G$1" symbol="MS1242" x="0" y="0"/>   </gates>@@ -140,7 +141,15 @@         <connect gate="G$1" pin="AIN3/D3" pad="10"/>         <connect gate="G$1" pin="AIN2/D2" pad="9"/>       </connects>-      <technologies><technology name=""/></technologies>+      <technologies>+        <technology name="">+          <attribute name="MPN" value="MS1242" constant="no"/>+          <attribute name="MANUFACTURER" value="Hangzhou Ruimeng Tech" constant="no"/>+          <attribute name="DATASHEET" value="https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588885031205154816" constant="no"/>+          <attribute name="ADOM_WIKI" value="https://wiki.adom.inc/adom/ms1242" constant="no"/>+          <attribute name="LCSC_PN" value="C482689" constant="no"/>+        </technology>+      </technologies>     </device>   </devices> </deviceset>
package.json+27−27
@@ -1,6 +1,6 @@ {   "slug": "ms1242",-  "version": "0.1.0",+  "version": "0.1.1",   "type": "component",   "description": "Hangzhou Ruimeng Tech Analog To Digital Converters (ADC), TSSOP-16. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",   "tags": [@@ -52,7 +52,7 @@       "lcsc": "C482689"     },     "distributor_check": {-      "checked_at": "2026-11-10T07:53:15Z",+      "checked_at": "2026-11-11T01:41:15Z",       "source": "Component Ocean /api/assign-pns",       "digikey": {         "pn": null,@@ -68,61 +68,61 @@         "number": "1",         "name": "VDD",         "type": "power_in",-        "description": "Power supply pin; the datasheet gives an operating supply range of 2.7 V to 5.25 V."+        "description": "Power supply pin; the datasheet gives an operating supply of 2.7 V to 5.25 V and an absolute maximum of -0.3 V to 6 V."       },       {         "number": "2",         "name": "XIN",         "type": "input",-        "description": "Clock input per the pin table, used with an external crystal (10-20 pF capacitors on MCLK and XTAL) or an external clock."+        "description": "Clock input pin for the crystal or oscillator; the system clock fosc is specified at 1 MHz to 5 MHz, and 10 pF to 20 pF capacitors are required on MCLK and XTAL when a crystal is used."       },       {         "number": "3",         "name": "XOUT",         "type": "output",-        "description": "Clock output per the pin table; the clock generator section states an external clock is applied through this pin with XTAL left floating."+        "description": "Clock output pin for the crystal; the datasheet also says an external clock is applied at this pin with XTAL left floating, which conflicts with the pin direction printed in the table."       },       {         "number": "4",         "name": "PDWN",         "type": "input",-        "description": "Power-down control signal, active low."+        "description": "Power-down control input, active low."       },       {         "number": "5",         "name": "VREF+",         "type": "power_in",-        "description": "Positive analog reference voltage input; the differential reference (REFP-REFN) must not exceed 2.5 V at VDD=5 V with RANGE=0, 5.0 V at VDD=5 V with RANGE=1, 1.25 V at VDD=3 V with RANGE=0, or 2.5 V at VDD=3 V with RANGE=1, and must not exceed VDD."+        "description": "Analog positive reference voltage input; the differential reference (REFP minus REFN) must not exceed 2.5 V at VDD=5 V with RANGE=0, or 1.25 V at VDD=3 V with RANGE=0, and must not exceed the supply voltage."       },       {         "number": "6",         "name": "VREF–",         "type": "power_in",-        "description": "Negative analog reference voltage input, forming the differential reference with VREF+ under the same limits as stated for the reference voltage."+        "description": "Analog negative reference voltage input, forming the differential reference pair with VREF+ (REFN); the reference voltage must not exceed the supply voltage."       },       {         "number": "7",         "name": "AIN0/D0",-        "type": "input",-        "description": "Analog input channel 0, which can also serve as data I/O pin D0 when configured via the IOCON, DIR and DIO registers; the power-up default is analog input."+        "type": "bidirectional",+        "description": "Analog input channel 0, also usable as data I/O bit 0; the analog input must stay within -0.5 V to VDD+0.5 V absolute maximum."       },       {         "number": "8",         "name": "AIN1/D1",-        "type": "input",-        "description": "Analog input channel 1, which can also serve as data I/O pin D1 when configured via the IOCON, DIR and DIO registers; the power-up default is analog input."+        "type": "bidirectional",+        "description": "Analog input channel 1, also usable as data I/O bit 1; the analog input must stay within -0.5 V to VDD+0.5 V absolute maximum."       },       {         "number": "9",         "name": "AIN2/D2",-        "type": "input",-        "description": "Analog input channel 2, which can also serve as data I/O pin D2 when configured via the IOCON, DIR and DIO registers; the power-up default is analog input."+        "type": "bidirectional",+        "description": "Analog input channel 2, also usable as data I/O bit 2; the analog input must stay within -0.5 V to VDD+0.5 V absolute maximum."       },       {         "number": "10",         "name": "AIN3/D3",-        "type": "input",-        "description": "Analog input channel 3, which can also serve as data I/O pin D3 when configured via the IOCON, DIR and DIO registers; the power-up default is analog input."+        "type": "bidirectional",+        "description": "Analog input channel 3, also usable as data I/O bit 3; the analog input must stay within -0.5 V to VDD+0.5 V absolute maximum."       },       {         "number": "11",@@ -134,31 +134,31 @@         "number": "12",         "name": "CS",         "type": "input",-        "description": "SPI chip select, active low; it must be held low for the whole communication, and when it goes high the SPI bus is reset."+        "description": "SPI chip select input, active low; it must be held low for the whole communication, and when it goes high the SPI bus is reset."       },       {         "number": "13",         "name": "DIN",         "type": "input",-        "description": "SPI serial data input, sampled on SCLK edges."+        "description": "SPI serial data input."       },       {         "number": "14",         "name": "DOUT",         "type": "output",-        "description": "SPI serial data output (SDO), which is high impedance when not in use so that DIN and DOUT can be tied together on a bidirectional bus."+        "description": "SPI serial data output; it is high impedance when not in use, allowing SDI and SDO to be tied together on a bidirectional bus."       },       {         "number": "15",         "name": "SCLK",         "type": "input",-        "description": "SPI serial clock input with Schmitt-trigger input, used to sample SDI and SDO and required to be clean to avoid sampling errors."+        "description": "SPI serial clock input with Schmitt-trigger input, used to sample SDI and SDO; it must be free of noise to avoid erroneous sampling."       },       {         "number": "16",         "name": "DRDY",         "type": "output",-        "description": "Data ready output, active low, which goes low when new conversion data is ready in the data output register."+        "description": "Data-ready output, active low; it goes low when new conversion data is available in the data output register."       }     ],     "provenance": {@@ -172,11 +172,11 @@         "consensus": "agreed",         "guards": "pin_guards 0.1: passed",         "guard_notes": [-          "extractor flagged: The pin table labels XIN as clock input and XOUT as clock output, but the clock generator section sa; Pins are printed as input (I) in the table, but they are also the data I/O pins D0–D3 selected throu; The datasheet states DOUT is high impedance when not in use, so its tri-state behavior is noted here"+          "extractor flagged: Pin 3 XOUT is listed as a clock output (O), but the clock section says that with an external clock t; The datasheet pin table lists AIN0/D0 to AIN3/D3 as inputs (I), but the data I/O function (IOCON/DIR; The pin table is for MS1242 (TSSOP16) only; the datasheet TSSOP16 pinout matches this part. The text"         ],         "pages_sent": 27,-        "cost_usd": 0.0916,-        "at": "2026-11-10T07:53:03"+        "cost_usd": 0.0938,+        "at": "2026-11-11T01:40:56"       },       "datasheet": {         "url": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588885031205154816",@@ -213,7 +213,7 @@         "centre_offset_mm": 0.0,         "footprint_binding": "identity",         "sha256": "6ad5e98224d02a427d9a6b929a28dbc158b9925fba5adec12db05079f1016948",-        "checked": "2026-11-10",+        "checked": "2026-11-11",         "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"       },       {@@ -231,8 +231,8 @@         "zmin_mm": -0.0,         "centre_offset_mm": 0.0,         "footprint_binding": "identity",-        "sha256": "02767e66249c786de09cd80a5057d1a4f8753fc13522244caf68e0c113b0e21a",-        "checked": "2026-11-10",+        "sha256": "b8ce3405ab61db421a5ac25cba55aa371eec8edd9721d39102d9fbbb5bd85518",+        "checked": "2026-11-11",         "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"       }     ]
page.json+30−28
@@ -4,7 +4,7 @@   "slug": "ms1242",   "title": "MS1242",   "brief": "Hangzhou Ruimeng Tech Analog To Digital Converters (ADC), TSSOP-16. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",-  "version": "0.1.0",+  "version": "0.1.1",   "license": "CC-BY-SA-4.0",   "tags": [     "component",@@ -34,7 +34,7 @@       "lcsc": "C482689"     },     "distributor_check": {-      "checked_at": "2026-11-10T07:53:15Z",+      "checked_at": "2026-11-11T01:41:15Z",       "source": "Component Ocean /api/assign-pns",       "digikey": {         "pn": null,@@ -50,61 +50,61 @@         "number": "1",         "name": "VDD",         "type": "power_in",-        "description": "Power supply pin; the datasheet gives an operating supply range of 2.7 V to 5.25 V."+        "description": "Power supply pin; the datasheet gives an operating supply of 2.7 V to 5.25 V and an absolute maximum of -0.3 V to 6 V."       },       {         "number": "2",         "name": "XIN",         "type": "input",-        "description": "Clock input per the pin table, used with an external crystal (10-20 pF capacitors on MCLK and XTAL) or an external clock."+        "description": "Clock input pin for the crystal or oscillator; the system clock fosc is specified at 1 MHz to 5 MHz, and 10 pF to 20 pF capacitors are required on MCLK and XTAL when a crystal is used."       },       {         "number": "3",         "name": "XOUT",         "type": "output",-        "description": "Clock output per the pin table; the clock generator section states an external clock is applied through this pin with XTAL left floating."+        "description": "Clock output pin for the crystal; the datasheet also says an external clock is applied at this pin with XTAL left floating, which conflicts with the pin direction printed in the table."       },       {         "number": "4",         "name": "PDWN",         "type": "input",-        "description": "Power-down control signal, active low."+        "description": "Power-down control input, active low."       },       {         "number": "5",         "name": "VREF+",         "type": "power_in",-        "description": "Positive analog reference voltage input; the differential reference (REFP-REFN) must not exceed 2.5 V at VDD=5 V with RANGE=0, 5.0 V at VDD=5 V with RANGE=1, 1.25 V at VDD=3 V with RANGE=0, or 2.5 V at VDD=3 V with RANGE=1, and must not exceed VDD."+        "description": "Analog positive reference voltage input; the differential reference (REFP minus REFN) must not exceed 2.5 V at VDD=5 V with RANGE=0, or 1.25 V at VDD=3 V with RANGE=0, and must not exceed the supply voltage."       },       {         "number": "6",         "name": "VREF–",         "type": "power_in",-        "description": "Negative analog reference voltage input, forming the differential reference with VREF+ under the same limits as stated for the reference voltage."+        "description": "Analog negative reference voltage input, forming the differential reference pair with VREF+ (REFN); the reference voltage must not exceed the supply voltage."       },       {         "number": "7",         "name": "AIN0/D0",-        "type": "input",-        "description": "Analog input channel 0, which can also serve as data I/O pin D0 when configured via the IOCON, DIR and DIO registers; the power-up default is analog input."+        "type": "bidirectional",+        "description": "Analog input channel 0, also usable as data I/O bit 0; the analog input must stay within -0.5 V to VDD+0.5 V absolute maximum."       },       {         "number": "8",         "name": "AIN1/D1",-        "type": "input",-        "description": "Analog input channel 1, which can also serve as data I/O pin D1 when configured via the IOCON, DIR and DIO registers; the power-up default is analog input."+        "type": "bidirectional",+        "description": "Analog input channel 1, also usable as data I/O bit 1; the analog input must stay within -0.5 V to VDD+0.5 V absolute maximum."       },       {         "number": "9",         "name": "AIN2/D2",-        "type": "input",-        "description": "Analog input channel 2, which can also serve as data I/O pin D2 when configured via the IOCON, DIR and DIO registers; the power-up default is analog input."+        "type": "bidirectional",+        "description": "Analog input channel 2, also usable as data I/O bit 2; the analog input must stay within -0.5 V to VDD+0.5 V absolute maximum."       },       {         "number": "10",         "name": "AIN3/D3",-        "type": "input",-        "description": "Analog input channel 3, which can also serve as data I/O pin D3 when configured via the IOCON, DIR and DIO registers; the power-up default is analog input."+        "type": "bidirectional",+        "description": "Analog input channel 3, also usable as data I/O bit 3; the analog input must stay within -0.5 V to VDD+0.5 V absolute maximum."       },       {         "number": "11",@@ -116,31 +116,31 @@         "number": "12",         "name": "CS",         "type": "input",-        "description": "SPI chip select, active low; it must be held low for the whole communication, and when it goes high the SPI bus is reset."+        "description": "SPI chip select input, active low; it must be held low for the whole communication, and when it goes high the SPI bus is reset."       },       {         "number": "13",         "name": "DIN",         "type": "input",-        "description": "SPI serial data input, sampled on SCLK edges."+        "description": "SPI serial data input."       },       {         "number": "14",         "name": "DOUT",         "type": "output",-        "description": "SPI serial data output (SDO), which is high impedance when not in use so that DIN and DOUT can be tied together on a bidirectional bus."+        "description": "SPI serial data output; it is high impedance when not in use, allowing SDI and SDO to be tied together on a bidirectional bus."       },       {         "number": "15",         "name": "SCLK",         "type": "input",-        "description": "SPI serial clock input with Schmitt-trigger input, used to sample SDI and SDO and required to be clean to avoid sampling errors."+        "description": "SPI serial clock input with Schmitt-trigger input, used to sample SDI and SDO; it must be free of noise to avoid erroneous sampling."       },       {         "number": "16",         "name": "DRDY",         "type": "output",-        "description": "Data ready output, active low, which goes low when new conversion data is ready in the data output register."+        "description": "Data-ready output, active low; it goes low when new conversion data is available in the data output register."       }     ],     "provenance": {@@ -154,11 +154,11 @@         "consensus": "agreed",         "guards": "pin_guards 0.1: passed",         "guard_notes": [-          "extractor flagged: The pin table labels XIN as clock input and XOUT as clock output, but the clock generator section sa; Pins are printed as input (I) in the table, but they are also the data I/O pins D0–D3 selected throu; The datasheet states DOUT is high impedance when not in use, so its tri-state behavior is noted here"+          "extractor flagged: Pin 3 XOUT is listed as a clock output (O), but the clock section says that with an external clock t; The datasheet pin table lists AIN0/D0 to AIN3/D3 as inputs (I), but the data I/O function (IOCON/DIR; The pin table is for MS1242 (TSSOP16) only; the datasheet TSSOP16 pinout matches this part. The text"         ],         "pages_sent": 27,-        "cost_usd": 0.0916,-        "at": "2026-11-10T07:53:03"+        "cost_usd": 0.0938,+        "at": "2026-11-11T01:40:56"       },       "datasheet": {         "url": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588885031205154816",@@ -195,7 +195,7 @@         "centre_offset_mm": 0,         "footprint_binding": "identity",         "sha256": "6ad5e98224d02a427d9a6b929a28dbc158b9925fba5adec12db05079f1016948",-        "checked": "2026-11-10",+        "checked": "2026-11-11",         "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"       },       {@@ -213,8 +213,8 @@         "zmin_mm": 0,         "centre_offset_mm": 0,         "footprint_binding": "identity",-        "sha256": "02767e66249c786de09cd80a5057d1a4f8753fc13522244caf68e0c113b0e21a",-        "checked": "2026-11-10",+        "sha256": "b8ce3405ab61db421a5ac25cba55aa371eec8edd9721d39102d9fbbb5bd85518",+        "checked": "2026-11-11",         "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"       }     ]@@ -993,5 +993,7 @@   ],   "visibility": {     "public": true-  }+  },+  "description": "Hangzhou Ruimeng Tech Analog To Digital Converters (ADC), TSSOP-16. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+  "org": "adom" }\ No newline at end of file