component
MPQ8113AGJ-AEC1-Z
Public Made by Adomby adom
Monolithic Power Systems Current-Sensing Amplifiers, TSOT-23-6L. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownMPQ8113AGJ-AEC1-Z
Monolithic Power Systems · Current-Sensing Amplifiers · TSOT-23-6L
MPQ8113AGJ-AEC1-Z from Monolithic Power Systems, in a TSOT-23-6L. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | OUT | output | Output; for the MPQ8113A connect an external resistor between OUT and ground to set the gain, while the MPQ8113 has an internal 10kΩ resistor to ground and OUT can be left floating. |
| 2 | RG2 | input | Negative gain resistor pin; for the MPQ8113A connect to the load side of the sense resistor through gain resistor RG2, which should be below 4kΩ (1kΩ recommended). |
| 3 | RG1 | input | Positive gain resistor pin that must not exceed the VCC voltage; for the MPQ8113A connect to the power side of the sense resistor through gain resistor RG1, which should be below 4kΩ (1kΩ recommended). |
| 4 | VCC | power_in | Power input supplying the internal input stage amplifier (2.7V to 60V); place a 0.1µF to 1µF low-ESR ceramic bypass capacitor to GND close to the pin. |
| 5 | GND | power_in | Ground. |
| 6 | V5 | power_in | Supply for internal control and output block (2.7V to 5.5V, source must supply above 5mA) that enables the part above 2V, disables it below 1.9V, and limits the maximum output voltage; use a 10nF to 100nF bypass capacitor to GND. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Monolithic Power Systems |
| Package | TSOT-23-6L |
| Category | Operational Amplifier/Comparator |
| Pins | 6 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | VCC | 2.7 | 60 | V | 5 | ||
| Common mode input voltage | VCM | 0 | 60 | V | 0 to VCC | 5 | |
| V5 supply voltage | V5 | 2.7 | 5.5 | V | 5 | ||
| Supply current | ICC + IV5 | 300 | 360 | µA | VSENSE = 0, VCC = 60V, V5 = 5V | 5 | |
| Common mode input rejection | CMR | 65 | 90 | dB | VSENSE = 80mV, VCC = 60V, VCM1 = 60V, VCM2 = 22V | 5 | |
| Input offset voltage | VOS | 0.3 | 1 | mV | VCM = 12V, VSENSE1 = 80mV, VSENSE2 = 20mV | 5 | |
| Input bias current | IRG1, IRG2 | 0.25 | 1 | µA | VCM = 12V | 5 | |
| Current-sense gain | GM | 4.95 | 5 | 5.05 | A/A | TJ = 25°C | 5 |
| Current-sense gain | GM | 4.9 | 5 | 5.1 | A/A | TJ = -40°C to +125°C | 5 |
| Power supply rejection ratio | PSRR | 70 | 80 | dB | VCC1 = 60V, VCC2 = 2.7V, VSENSE = 24mV | 5 | |
| V5 upper threshold voltage | VTH_UPPER | 1.3 | 2 | 2.5 | V | 5 | |
| V5 lower threshold voltage | VTH_LOWER | 1.2 | 1.9 | 2.4 | V | 5 | |
| V5 shutdown supply current | ICC(SHDN) | 0.2 | 2 | µA | V5 = 1V | 5 | |
| Full-scale sense voltage | VSENSE | 200 | mV | MPQ8113A, VSENSE = VRG1 - VRG2 | 5 | ||
| Bandwidth | BW | 700 | kHz | COUT = 5pF, AV = 50V/V, (RG1 = RG2 = 1kΩ, ROUT = 10kΩ), small signal -3dB bandwidth | 5 | ||
| Bandwidth | BW | 1400 | kHz | COUT = 5pF, AV = 20V/V, (RG1 = RG2 = 1kΩ, ROUT = 4kΩ), small signal -3dB bandwidth | 5 | ||
| Output respond time | 500 | ns | RG1 = RG2 = 1kΩ, ROUT = 10kΩ, VSENSE = 5mV to 80mV, VOUT from 10% to 90% | 6 | |||
| Output respond time | 250 | ns | RG1 = RG2 = 1kΩ, ROUT = 4kΩ, VSENSE = 5mV to 100mV, VOUT from 10% to 90% | 6 | |||
| VCC to GND | VCC | -0.3 | 62 | V | 4 | ||
| RG1, RG2 to GND | -0.3 | V | -0.3V to VCC | 4 | |||
| VCC to RG1, RG2 | -0.3 | 62 | V | 4 | |||
| OUT to GND | -0.3 | V | -0.3V to V5 | 4 | |||
| Differential input voltage | VRG1 - VRG2 | -400 | 400 | mV | 4 | ||
| V5 to GND | V5 | -0.3 | 6 | V | 4 | ||
| Max junction temperature | TJ | 150 | °C | 4 | |||
| Storage temperature | -65 | 150 | °C | 4 | |||
| ESD HBM | -2 | 2 | kV | Human body model | 4 | ||
| ESD CDM | -750 | 750 | V | Charged device model | 4 | ||
| VCC to GND | VCC | 2.7 | 60 | V | 4 | ||
| RG1, RG2 to GND | 0 | V | 0V to VCC | 4 | |||
| VCC to RG1, RG2 | 0 | 60 | V | 4 | |||
| V5 to GND | V5 | 2.7 | 5.5 | V | 4 | ||
| OUT to GND | 0 | V | 0V to V5 - 1V | 4 | |||
| Operating junction temperature | TJ | -40 | 125 | °C | 4 | ||
| Thermal resistance junction-to-ambient | θJA | 220 | °C/W | TSOT23-6L, JESD51-7 4-layer PCB | 4 | ||
| Thermal resistance junction-to-case | θJC | 110 | °C/W | TSOT23-6L, JESD51-7 4-layer PCB | 4 |
CAD (KiCad official)
- Symbol:
MPQ8113AGJ-AEC1-Z - Footprint:
Package_TO_SOT_SMD:TSOT-23-6 - 3D model: TSOT-23-6L (KiCad packages3D, STEP)
- 3D model files:
mpq8113agj-aec1-z-etched.step/mpq8113agj-aec1-z-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mpq8113agj-aec1-z.step/mpq8113agj-aec1-z.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Monolithic Power Systems datasheet (21 pp, sha256
2cd09c2322087364, retrieved 2026-10-31, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).