main
Ray
Publish 0.1.0
2fd0531
MPQ7220GR-AEC1-Z
Monolithic Power Systems · LED Drivers · QFN-24(4x4)
MPQ7220GR-AEC1-Z from Monolithic Power Systems, in a QFN-24(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | DIM | input | PWM dimming input for brightness control, pulled low internally, 100Hz to 20kHz PWM recommended, pull high if dimming is not used. |
| 2 | NC | unconnected | Not connected. |
| 3 | FREQ/SYNC | input | Switching frequency setting via a resistor to GND, or external clock input to sync the boost switching frequency. |
| 4 | EN | input | IC enable pin; pull high to enable the IC, pull low to force shutdown mode. |
| 5 | AGND | power_in | Analog ground. |
| 6 | AGND | power_in | Analog ground. |
| 7 | COMP | passive | Compensation pin. |
| 8 | FF | output | Fault flag pin, open drain during normal operation and pulled low in any fault mode; float if not used. |
| 9 | ISET | passive | LED current setting; tie a current-setting resistor from this pin to ground to program the current in each LED string. |
| 10 | AGND | power_in | Analog ground. |
| 11 | LED6 | input | LED string 6 current input; connect the string 6 cathode to this pin. |
| 12 | LED5 | input | LED string 5 current input; connect the string 5 cathode to this pin. |
| 13 | LED4 | input | LED string 4 current input; connect the string 4 cathode to this pin. |
| 14 | LED3 | input | LED string 3 current input; connect the string 3 cathode to this pin. |
| 15 | LED2 | input | LED string 2 current input; connect the string 2 cathode to this pin. |
| 16 | LED1 | input | LED string 1 current input; connect the string 1 cathode to this pin. |
| 17 | PGND | power_in | Step-up converter power ground. |
| 18 | SW | passive | Drain of the internal low-side MOSFET switch; connect the power inductor to SW. |
| 19 | OVP | input | Over-voltage protection pin; use a voltage divider to program the OVP threshold and do not float this pin. |
| 20 | STH | passive | Short LED protection threshold set pin with 18µA current source out; resistor to GND sets the threshold, which is 5V if floated. |
| 21 | FSP | passive | Spread spectrum pin with 18µA current source out; resistor to GND sets voltage: <0.4V jitter 1/20 of center frequency, 0.45V to 1.4V jitter 1/32, >1.4V or floated disables spread spectrum. |
| 22 | VCC | power_out | 5V LDO output powering internal logic and gate driver; place a ceramic capacitor as close as possible to this pin. |
| 23 | SD | output | External disconnect PMOS gate drive pin that turns off the external PMOS in a fault condition; float if not used. |
| 24 | VIN | power_in | Power supply input for the IC, 3.5V to 36V recommended operating range. |
| 25 | Exposed pad | passive | Exposed pad with no internal electrical connection to AGND and PGND; connect to external GND plane on the board for optimal thermal performance. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Monolithic Power Systems |
| Package | QFN-24(4x4) |
| Category | LED Drivers |
| Pins | 25 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Switching frequency (RFREQ=10kΩ) | fSW | -10 | 10 | % | RFREQ = 10kΩ (2.2 MHz typ) | 7 | |
| Switching frequency (RFREQ=46.8kΩ) | fSW | -10 | 10 | % | RFREQ = 46.8kΩ (470 kHz typ) | 7 | |
| Switching frequency (FREQ float) | fSW | -20 | 20 | % | FREQ float (400 kHz typ) | 7 | |
| FREQ voltage | VFREQ | -5 | 5 | % | 0.6 V typ | 7 | |
| Cycle-by-cycle current limit | ISW_LIMIT | 2.3 | 4 | A | Duty = 90% | 7 | |
| LEDX regulation voltage | VHD | 700 | 850 | 1000 | mV | ILED = 100mA | 8 |
| Current matching | -2.5 | 2.5 | % | ILED = 20mA | 8 | ||
| LED current accuracy | ILED | -2.5 | 50 | 2.5 | % | RISET = 24.9kΩ, TJ = 25°C (typ 50 mA) | 8 |
| LED current accuracy over temperature | ILED | -4 | 50 | 4 | % | RISET = 24.9kΩ, TJ = -40°C to +125°C, no over-temperature LED current decrement (typ 50 mA) | 8 |
| Over-voltage protection threshold | VOVP | 1.9 | 2 | 2.1 | V | 8 | |
| LEDX over-voltage threshold | VLEDX_OV | 4.3 | 4.7 | 5.1 | V | STH floating or VSTH = 0.5V | 8 |
| LEDX over-voltage fault timer | 6 | 7.7 | 10 | ms | 8 | ||
| SD pull-down current | ISD | 40 | 55 | 70 | µA | 8 | |
| Operating input voltage | VIN | 3.5 | 36 | V | 7 | ||
| Supply current (quiescent) | IQ | 5 | mA | No switching | 7 | ||
| Supply current (shutdown) | IST | 1 | μA | VEN = 0V, VIN = 12V | 7 | ||
| Input UVLO threshold | VIN_UVLO | 3.1 | V | Rising edge | 7 | ||
| LDO output voltage | VCC | 5 | V | VEN = 2V, 6V < VIN < 24V, 0 < IVCC < 10mA | 7 | ||
| Low-side MOS on resistance | RDS_LS | 100 | mΩ | VIN = 3.7V | 7 | ||
| Current limit protection | ICL | 8 | A | To trigger current limit protection | 7 | ||
| Thermal shutdown threshold | TST | 170 | °C | Rising edge | 8 | ||
| Input voltage | VIN | -0.3 | 42 | V | 6 | ||
| SW and LED1-6 voltage | VSW, VLED1-6 | -0.5 | 50 | V | 6 | ||
| All other pins | -0.3 | 6.5 | V | 6 | |||
| Junction temperature | TJ | 150 | °C | 6 | |||
| Storage temperature | TSTG | -65 | 150 | °C | 6 | ||
| Continuous power dissipation QFN-24 | PD | 2.97 | W | TA = 25°C | 6 | ||
| Supply voltage | VIN | 3.5 | 36 | V | 6 | ||
| Operating junction temperature | TJ | -40 | 125 | °C | 6 | ||
| Thermal resistance θJA QFN-24 | θJA | 42 | °C/W | JESD51-7 | 6 |
CAD (KiCad official)
- Symbol:
MPQ7220GR-AEC1-Z - Footprint:
Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm - 3D model: QFN-24(4x4) (KiCad packages3D, STEP)
- 3D model files:
mpq7220gr-aec1-z-etched.step/mpq7220gr-aec1-z-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mpq7220gr-aec1-z.step/mpq7220gr-aec1-z.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Monolithic Power Systems datasheet (32 pp, sha256
4ec59af25be1ccfa, retrieved 2026-10-27, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# MPQ7220GR-AEC1-Z
**Monolithic Power Systems** · LED Drivers · QFN-24(4x4)
MPQ7220GR-AEC1-Z from Monolithic Power Systems, in a QFN-24(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | DIM | input | PWM dimming input for brightness control, pulled low internally, 100Hz to 20kHz PWM recommended, pull high if dimming is not used. |
| 2 | NC | unconnected | Not connected. |
| 3 | FREQ/SYNC | input | Switching frequency setting via a resistor to GND, or external clock input to sync the boost switching frequency. |
| 4 | EN | input | IC enable pin; pull high to enable the IC, pull low to force shutdown mode. |
| 5 | AGND | power_in | Analog ground. |
| 6 | AGND | power_in | Analog ground. |
| 7 | COMP | passive | Compensation pin. |
| 8 | FF | output | Fault flag pin, open drain during normal operation and pulled low in any fault mode; float if not used. |
| 9 | ISET | passive | LED current setting; tie a current-setting resistor from this pin to ground to program the current in each LED string. |
| 10 | AGND | power_in | Analog ground. |
| 11 | LED6 | input | LED string 6 current input; connect the string 6 cathode to this pin. |
| 12 | LED5 | input | LED string 5 current input; connect the string 5 cathode to this pin. |
| 13 | LED4 | input | LED string 4 current input; connect the string 4 cathode to this pin. |
| 14 | LED3 | input | LED string 3 current input; connect the string 3 cathode to this pin. |
| 15 | LED2 | input | LED string 2 current input; connect the string 2 cathode to this pin. |
| 16 | LED1 | input | LED string 1 current input; connect the string 1 cathode to this pin. |
| 17 | PGND | power_in | Step-up converter power ground. |
| 18 | SW | passive | Drain of the internal low-side MOSFET switch; connect the power inductor to SW. |
| 19 | OVP | input | Over-voltage protection pin; use a voltage divider to program the OVP threshold and do not float this pin. |
| 20 | STH | passive | Short LED protection threshold set pin with 18µA current source out; resistor to GND sets the threshold, which is 5V if floated. |
| 21 | FSP | passive | Spread spectrum pin with 18µA current source out; resistor to GND sets voltage: <0.4V jitter 1/20 of center frequency, 0.45V to 1.4V jitter 1/32, >1.4V or floated disables spread spectrum. |
| 22 | VCC | power_out | 5V LDO output powering internal logic and gate driver; place a ceramic capacitor as close as possible to this pin. |
| 23 | SD | output | External disconnect PMOS gate drive pin that turns off the external PMOS in a fault condition; float if not used. |
| 24 | VIN | power_in | Power supply input for the IC, 3.5V to 36V recommended operating range. |
| 25 | Exposed pad | passive | Exposed pad with no internal electrical connection to AGND and PGND; connect to external GND plane on the board for optimal thermal performance. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Monolithic Power Systems |
| Package | QFN-24(4x4) |
| Category | LED Drivers |
| Pins | 25 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Switching frequency (RFREQ=10kΩ) | fSW | -10 | | 10 | % | RFREQ = 10kΩ (2.2 MHz typ) | 7 |
| Switching frequency (RFREQ=46.8kΩ) | fSW | -10 | | 10 | % | RFREQ = 46.8kΩ (470 kHz typ) | 7 |
| Switching frequency (FREQ float) | fSW | -20 | | 20 | % | FREQ float (400 kHz typ) | 7 |
| FREQ voltage | VFREQ | -5 | | 5 | % | 0.6 V typ | 7 |
| Cycle-by-cycle current limit | ISW_LIMIT | 2.3 | | 4 | A | Duty = 90% | 7 |
| LEDX regulation voltage | VHD | 700 | 850 | 1000 | mV | ILED = 100mA | 8 |
| Current matching | | -2.5 | | 2.5 | % | ILED = 20mA | 8 |
| LED current accuracy | ILED | -2.5 | 50 | 2.5 | % | RISET = 24.9kΩ, TJ = 25°C (typ 50 mA) | 8 |
| LED current accuracy over temperature | ILED | -4 | 50 | 4 | % | RISET = 24.9kΩ, TJ = -40°C to +125°C, no over-temperature LED current decrement (typ 50 mA) | 8 |
| Over-voltage protection threshold | VOVP | 1.9 | 2 | 2.1 | V | | 8 |
| LEDX over-voltage threshold | VLEDX_OV | 4.3 | 4.7 | 5.1 | V | STH floating or VSTH = 0.5V | 8 |
| LEDX over-voltage fault timer | | 6 | 7.7 | 10 | ms | | 8 |
| SD pull-down current | ISD | 40 | 55 | 70 | µA | | 8 |
| Operating input voltage | VIN | 3.5 | | 36 | V | | 7 |
| Supply current (quiescent) | IQ | | 5 | | mA | No switching | 7 |
| Supply current (shutdown) | IST | | 1 | | μA | VEN = 0V, VIN = 12V | 7 |
| Input UVLO threshold | VIN_UVLO | | 3.1 | | V | Rising edge | 7 |
| LDO output voltage | VCC | | 5 | | V | VEN = 2V, 6V < VIN < 24V, 0 < IVCC < 10mA | 7 |
| Low-side MOS on resistance | RDS_LS | | 100 | | mΩ | VIN = 3.7V | 7 |
| Current limit protection | ICL | | 8 | | A | To trigger current limit protection | 7 |
| Thermal shutdown threshold | TST | | 170 | | °C | Rising edge | 8 |
| Input voltage | VIN | -0.3 | | 42 | V | | 6 |
| SW and LED1-6 voltage | VSW, VLED1-6 | -0.5 | | 50 | V | | 6 |
| All other pins | | -0.3 | | 6.5 | V | | 6 |
| Junction temperature | TJ | | | 150 | °C | | 6 |
| Storage temperature | TSTG | -65 | | 150 | °C | | 6 |
| Continuous power dissipation QFN-24 | PD | | | 2.97 | W | TA = 25°C | 6 |
| Supply voltage | VIN | 3.5 | | 36 | V | | 6 |
| Operating junction temperature | TJ | -40 | | 125 | °C | | 6 |
| Thermal resistance θJA QFN-24 | θJA | | 42 | | °C/W | JESD51-7 | 6 |
## CAD (KiCad official)
- Symbol: `MPQ7220GR-AEC1-Z`
- Footprint: `Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm`
- 3D model: QFN-24(4x4) (KiCad packages3D, STEP)
- 3D model files: `mpq7220gr-aec1-z-etched.step` / `mpq7220gr-aec1-z-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `mpq7220gr-aec1-z.step` / `mpq7220gr-aec1-z.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Monolithic Power Systems datasheet](docs/mpq7220gr-aec1-z-datasheet.pdf) (32 pp, sha256 `4ec59af25be1ccfa`, retrieved 2026-10-27, tier: lcsc)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/mpq7220gr-aec1-z-datasheet.pdf)