Generated by kicad-footprint-generator · KiCad file format 20260206
MPQ6610GJ-AEC1-Z
Monolithic Power Systems · Motor Driver ICs · TSOT-23-8
MPQ6610GJ-AEC1-Z from Monolithic Power Systems, in a TSOT-23-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | EN | input | H-bridge enable input; drive EN high to enable the half-bridge driver, with an internal pull-down resistor. |
| 2 | IN | input | H-bridge input pin; drive IN high to drive the output high, with an internal pull-down resistor. |
| 3 | ISET | passive | Current configuration pin; connect a resistor from ISET to ground to set the current limit and ISET pin voltage scaling (abs max -0.3V to +5.5V). |
| 4 | nFAULT | output | Open-drain fault indication output that is logic low on a fault condition (OCP, OTP, or open load) and requires an external pull-up resistor. |
| 5 | GND | power_in | System ground connection. |
| 6 | OUT | output | Half-bridge output terminal, rated -0.7V to +65V absolute maximum with up to ±3A output current. |
| 7 | VIN | power_in | Input supply voltage, 4V to 45V recommended for TSOT23 (abs max 65V); decouple to GND with a minimum 100nF ceramic capacitor. |
| 8 | BST | passive | Bootstrap pin; connect a 100nF capacitor between BST and OUT. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Monolithic Power Systems |
| Package | TSOT-23-8 |
| Category | Power Management |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input supply voltage (TSOT23) | VIN | 4 | 45 | V | TSOT23 package | 4 | |
| Quiescent current | IQ | 1.3 | 5 | mA | VIN = 24V, EN = 0, no load current | 4 | |
| HS on resistance 25C | RHS | 100 | 120 | mΩ | VIN = 24V, IOUT = 1A, TJ = 25°C | 4 | |
| HS on resistance 125C | RHS | 120 | 200 | mΩ | VIN = 24V, IOUT = 1A, TJ = 125°C | 4 | |
| LS on resistance 25C | RLS | 120 | 150 | mΩ | VIN = 24V, IOUT = 1A, TJ = 25°C | 4 | |
| LS on resistance 125C | RLS | 150 | 256 | mΩ | VIN = 24V, IOUT = 1A, TJ = 125°C | 4 | |
| Body diode forward voltage | VF | 1.1 | V | IOUT = 1A | 4 | ||
| Input logic low threshold | VIL | 0.8 | V | 4 | |||
| Input logic high threshold | VIH | 2 | V | 4 | |||
| Logic input current high | IIN(H) | 6 | 14 | µA | VIH = 5V | 4 | |
| Logic input current low | IIN(L) | 4 | µA | VIL = 0.8V | 4 | ||
| nFAULT output low voltage | VOL | 0.8 | V | IOUT = 5mA | 4 | ||
| nFAULT output high leakage current | IOH | 1 | µA | VOUT = 3.3V | 4 | ||
| OVP rising threshold | VOV_RISE | 55 | 65 | V | 4 | ||
| Internal pull-down resistance | RPD | 530 | kΩ | 4 | |||
| UVLO rising threshold | VUV_RISE | 4.1 | V | 4 | |||
| UVLO hysteresis | VUV_HYS | 300 | mV | 4 | |||
| OVP hysteresis | VOV_YS | 900 | mV | 4 | |||
| Over-current trip level sink | IOCP1 | 3 | A | Sink | 4 | ||
| Over-current trip level source | IOCP2 | 3 | A | Source | 4 | ||
| Over-current deglitch time | tOCP | 1 | µs | Not tested in production | 4 | ||
| Over-current retry time | tOCPR | 1.6 | ms | 4 | |||
| Thermal shutdown | TTSD | 165 | °C | 4 | |||
| Thermal shutdown hysteresis | ΔTTSD | 15 | °C | 4 | |||
| Open-load current detection | IOLD | 90 | µA | 4 | |||
| Open-load detection threshold, OUT low | VOLD | 1 | 1.5 | V | OUT = low | 4 | |
| Open-load detection threshold, OUT high | VOLD | 21.5 | 23.2 | V | OUT = high, VIN = 24V | 4 | |
| Off time | tITRIP | 16.5 | µs | After VITRIP is reached | 5 | ||
| Blanking time | tBLANK | 1 | µs | 5 | |||
| ISET current HS source | IISET | 69 | 90 | 118 | µA/A | HS source, IOUT = 1A | 5 |
| ISET current HS sink | IISET | 82 | 102 | 131 | µA/A | HS sink, IOUT = 1A | 5 |
| ISET current LS source | IISET | 83 | 104 | 130 | µA/A | LS source, IOUT = 1A | 5 |
| ISET current LS sink | IISET | 82 | 103 | 129 | µA/A | LS sink, IOUT = 1A | 5 |
| Current trip voltage | VITRIP | 1.4 | 1.5 | 1.6 | V | At ISET pin | 5 |
| Supply voltage (VIN) | VIN | -0.3 | 65 | V | 3 | ||
| OUT voltage | VOUT | -0.7 | 65 | V | 3 | ||
| ISET voltage | ISET | -0.3 | 5.5 | V | 3 | ||
| All other pins to GND | -0.3 | 6.5 | V | 3 | |||
| Continuous power dissipation TSOT23 | PD | 1.25 | W | TA = 25°C | 3 | ||
| Storage temperature | TSTG | -55 | 150 | °C | 3 | ||
| Junction temperature | TJ | 150 | °C | 3 | |||
| ESD HBM | 2 | kV | Human body model | 3 | |||
| ESD CDM | -750 | 750 | V | Charged device model | 3 | ||
| Supply voltage (SOT23) | VIN | 4 | 45 | V | 3 | ||
| Output current | IOUT | -3 | 3 | A | 3 | ||
| Operating junction temperature | TJ | -40 | 125 | °C | 3 | ||
| Thermal resistance junction-ambient TSOT23 | θJA | 100 | °C/W | JESD51-7, 4-layer PCB | 3 | ||
| Thermal resistance junction-case TSOT23 | θJC | 55 | °C/W | JESD51-7, 4-layer PCB | 3 |
CAD (KiCad official)
- Symbol:
MPQ6610GJ-AEC1-Z - Footprint:
Package_TO_SOT_SMD:TSOT-23-8 - 3D model: TSOT-23-8 (KiCad packages3D, STEP)
- 3D model files:
mpq6610gj-aec1-z-etched.step/mpq6610gj-aec1-z-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mpq6610gj-aec1-z.step/mpq6610gj-aec1-z.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Monolithic Power Systems datasheet (16 pp, sha256
0b4846b1f5a89a5b, retrieved 2026-10-23, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).