main
Ray Publish 0.1.0 3d6f23d

MPQ4436AGRE-AEC1-Z

Monolithic Power Systems · DC-DC Converters · QFN-20(4x4)

MPQ4436AGRE-AEC1-Z from Monolithic Power Systems, in a QFN-20(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 MODE input AAM or FCCM select pin: pull high to put the part in FCCM and pull low for AAM at light load, and do not leave it floating.
2 SYNCIN input SYNC input that synchronizes the internal oscillator to an external 350kHz to 1000kHz clock; connect a 51kΩ resistor between SYNCIN and GND, connect to GND if not used, and do not float it.
3 VIN power_in Input supply for the internal control circuitry and the power switch connected to SW, with a decoupling capacitor to ground recommended close to VIN.
4 PGND power_in Power ground.
5 PGND power_in Power ground.
6 BST power_out Bootstrap positive power supply for the high-side MOSFET driver connected to SW, requiring a bypass capacitor between BST and SW sized per the application section.
7 SW output Switch node and output of the internal power switch.
8 SW output Switch node and output of the internal power switch.
9 EN input Enable pin: pull below the 0.85V threshold to shut down the chip and pull above the 1V threshold to enable it.
10 PGND power_in Power ground.
11 PGND power_in Power ground.
12 VIN power_in Input supply for the internal control circuitry and the power switch connected to SW, with a decoupling capacitor to ground recommended close to VIN.
13 SYNCO output SYNC output providing a clock 180° out-of-phase with the internal oscillator or opposite to the SYNCIN clock; leave floating if not used.
14 PG output Open-drain power good output that goes high when the output is within 93% to 106% of nominal and low above 107.5% or below 91%, requiring a pull-up resistor to the power source if used.
15 ICS passive Current sharing pin: connect in parallel ICs in multi-phase applications, and in single-phase applications connect to VCC or to VOUT that is at least 3V; do not float it.
16 VCC power_out Bias supply powering the internal control circuit and gate drivers, requiring a decoupling capacitor to ground close to this pin.
17 AGND power_in Analog ground.
18 FB input Feedback input with a 0.815V feedback threshold voltage, connected to the center point of the output resistor divider to AGND and placed as close to FB as possible.
19 SS passive Soft start input: a capacitor from SS to GND sets the soft-start period, with a 6µA source current charging it at start-up to limit inrush current.
20 FREQ input Switching frequency program: a resistor from this pin to ground sets the switching frequency, following the fSW vs. RFREQ curve in the Typical Performance Characteristics section.
21 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Monolithic Power Systems
Package QFN-20(4x4)
Category Power Supply Chip
Pins 21

CAD (KiCad official)

  • Symbol: MPQ4436AGRE-AEC1-Z
  • Footprint: Package_DFN_QFN:QFN-20-1EP_4x4mm_P0.5mm_EP2.5x2.5mm
  • 3D model: QFN-20(4x4) (KiCad packages3D, STEP)
  • 3D model files: mpq4436agre-aec1-z-etched.step / mpq4436agre-aec1-z-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); mpq4436agre-aec1-z.step / mpq4436agre-aec1-z.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Monolithic Power Systems datasheet (38 pp, sha256 71ef689792c1986b, retrieved 2026-10-28, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF