3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownMPQ4418GJ-AEC1-Z
Monolithic Power Systems · DC-DC Converters · TSOT-23-8
MPQ4418GJ-AEC1-Z from Monolithic Power Systems, in a TSOT-23-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | PG | output | Open-drain power-good output that is pulled high when VOUT exceeds 90% of the nominal voltage. |
| 2 | IN | power_in | Supply voltage input operating from 4V to 36V, requiring an input capacitor (C1) placed close to the pin to decouple the input rail. |
| 3 | SW | output | Switch output of the internal power switch. |
| 4 | GND | power_in | Reference system ground and the reference ground of the regulated VOUT, to be connected to system ground with copper traces and vias. |
| 5 | BST | passive | Bootstrap pin where a capacitor is connected between SW and BST to form the floating supply for the high-side MOSFET driver, with a 20Ω resistor between SW and BST recommended to reduce SW voltage spikes. |
| 6 | EN/SYNC | input | Enable/synchronous input that turns the device on when driven high and sets the switching frequency when an external clock (200kHz to 2.2MHz) is applied. |
| 7 | VCC | power_out | Internal bias supply (regulator output) to be decoupled with a 0.1μF to 0.22μF capacitor that must not exceed 0.22μF. |
| 8 | FB | input | Feedback input connected to the tap of an external resistor divider from the output to GND to set VOUT, with frequency foldback when VFB drops below 660mV. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Monolithic Power Systems |
| Package | TSOT-23-8 |
| Category | Power Management |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage (absolute max) | VIN | -0.3 | 40 | V | 3 | ||
| Switch voltage (absolute max) | VSW | -0.3 | 41 | V | 3 | ||
| Bootstrap voltage (absolute max) | VBS | 6 | V | VSW + 6V (max relative to VSW) | 3 | ||
| All other pins (absolute max) | -0.3 | 6 | V | 3 | |||
| Continuous power dissipation | PD | 1.25 | W | TA = 25°C, TSOT23-8 | 3 | ||
| Junction temperature (absolute max) | TJ | 150 | °C | 3 | |||
| Storage temperature | -65 | 150 | °C | 3 | |||
| ESD HBM | -2000 | 2000 | V | Human body model | 3 | ||
| ESD CDM | -750 | 750 | V | Charged device model | 3 | ||
| Continuous supply voltage | VIN | 4 | 36 | V | 3 | ||
| Output voltage | VOUT | 0.8 | V | 0.8V to 0.9 x VIN | 3 | ||
| Operating junction temperature | TJ | -40 | 125 | °C | 3 | ||
| Junction-to-ambient thermal resistance | θJA | 100 | °C/W | TSOT23-8, JESD51-7 4-layer PCB | 3 | ||
| Junction-to-case thermal resistance | θJC | 55 | °C/W | TSOT23-8, JESD51-7 4-layer PCB | 3 | ||
| Shutdown supply current | ISHDN | 8 | μA | VEN = 0V | 4 | ||
| Quiescent supply current | IQ | 0.6 | 0.8 | mA | VEN = 2V, VFB = 1V, no switching | 4 | |
| High-side on resistance | RON_HS | 90 | 155 | mΩ | VBST_SW = 5V | 4 | |
| Low-side on resistance | RON_LS | 55 | 105 | mΩ | VCC = 5V | 4 | |
| Switch leakage | ILKG_SW | 1 | μA | VEN = 0V, VSW = 12V | 4 | ||
| Current limit | ILIMIT | 3.4 | 5.6 | 7.8 | A | Under 40% duty cycle | 4 |
| Oscillator frequency | fSW | 320 | 410 | 500 | kHz | VFB = 750mV | 4 |
| Foldback frequency | fFB | 70 | 100 | 130 | kHz | VFB < 400mV | 4 |
| Maximum duty cycle | DMAX | 92 | 95 | % | VFB = 750mV, 410kHz | 4 | |
| Minimum on time | tON_MIN | 70 | ns | Guaranteed by design | 4 | ||
| SYNC frequency range | fSYNC | 0.2 | 2.4 | MHz | 4 | ||
| Feedback voltage | VFB | 780 | 792 | 804 | mV | TJ = 25°C | 4 |
| Feedback voltage (over temperature) | VFB | 776 | 808 | mV | 4 | ||
| FB current | IFB | 10 | 100 | nA | VFB = 820mV | 4 | |
| EN rising threshold | VEN_RISING | 1.15 | 1.4 | 1.65 | V | 4 | |
| EN falling threshold | VEN_FALLING | 1.05 | 1.25 | 1.45 | V | 4 | |
| EN threshold hysteresis | VEN_HYS | 150 | mV | 4 | |||
| EN input current | IEN | 4 | 6 | μA | VEN = 2V | 4 | |
| EN input current | IEN | 0 | 0.2 | μA | VEN = 0V | 4 | |
| VIN UVLO rising threshold | VIN_UVLO_RISING | 3.3 | 3.5 | 3.7 | V | 4 | |
| VIN UVLO falling threshold | VIN_UVLO_FALLING | 3.1 | 3.3 | 3.5 | V | 4 | |
| VIN UVLO threshold hysteresis | VIN_UVLO_HYS | 200 | mV | 4 | |||
| VCC regulator | VCC | 4.6 | 4.9 | 5.2 | V | ICC = 0mA | 4 |
| VCC load regulation | 1.5 | 4 | % | ICC = 5mA | 4 | ||
| Soft-start time | tSS | 0.55 | 1.45 | 2.45 | ms | VOUT from 10% to 90% | 4 |
| Thermal shutdown | TSD | 150 | 170 | °C | Guaranteed by design | 4 | |
| Thermal hysteresis | 30 | °C | Guaranteed by design | 4 | |||
| PG rising threshold | PGVTH_RISING | 86 | 90 | 94 | % | As a percentage of VFB | 4 |
| PG falling threshold | PGVTH_FALLING | 80 | 84 | 88 | % | As a percentage of VFB | 4 |
| PG threshold hysteresis | PGVTH_HYS | 6 | % | As a percentage of VFB | 5 | ||
| PG rising delay | PGTD_RISING | 40 | 90 | 160 | μs | 5 | |
| PG falling delay | PGTD_FALLING | 30 | 55 | 95 | μs | 5 | |
| PG sink voltage | VPG | 0.1 | 0.3 | V | Sink 4mA | 5 | |
| PG leakage current | ILKG_PG | 10 | 100 | nA | 5 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | Reference system ground. The GND pin is critical to PCB layout design. GND is the reference ground of the regulated VOUT. Use copper traces and vias to connect GND to | 3 |
CAD (KiCad official)
- Symbol:
MPQ4418GJ-AEC1-Z - Footprint:
Package_TO_SOT_SMD:TSOT-23-8 - 3D model: TSOT-23-8 (KiCad packages3D, STEP)
- 3D model files:
mpq4418gj-aec1-z-etched.step/mpq4418gj-aec1-z-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mpq4418gj-aec1-z.step/mpq4418gj-aec1-z.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Monolithic Power Systems datasheet (20 pp, sha256
c62765e730b01bef, retrieved 2026-10-31, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).