main
Ray Publish 0.1.0 0c4f873

MPQ4317GRE-AEC1-Z

Monolithic Power Systems · DC-DC Converters · QFN-20(4x4)

MPQ4317GRE-AEC1-Z from Monolithic Power Systems, in a QFN-20(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 MODE input AAM or FCCM selection pin; pull high for forced continuous conduction mode (FCCM) and low for advanced asynchronous modulation (AAM) under light load, and do not leave it floating.
2 SYNCIN input SYNC input accepts a 350kHz to 1000kHz clock to synchronize the internal oscillator, and must not be left floating.
3 VIN power_in Input supply that powers the internal control circuitry and the power MOSFET connected to SW, with a decoupling capacitor placed close to VIN.
4 PGND power_in Power ground for the regulator.
5 PGND power_in Power ground for the regulator.
6 BST power_out Bootstrap pin that is the positive supply for the high-side MOSFET driver, with a bypass capacitor connected between BST and SW.
7 SW output Switch node that is the output of the internal power MOSFET.
8 SW output Switch node that is the output of the internal power MOSFET.
9 EN input Enable pin that turns the MPQ4317 on when pulled above 1V and turns the chip off when pulled below 0.85V.
10 PGND power_in Power ground for the regulator.
11 PGND power_in Power ground for the regulator.
12 VIN power_in Input supply that powers the internal control circuitry and the power MOSFET connected to SW, with a decoupling capacitor placed close to VIN.
13 SYNCO output SYNC output that provides a clock 180° out-of-phase with the internal oscillator, and should be floated if not used.
14 PG output Open-drain power good output that goes high when VOUT is within 95% to 105% of nominal and goes low when VOUT is above 106.5% or below 93%, requiring a pull-up resistor if used.
15 NC unconnected Not connected; float this pin.
16 VCC power_out Bias supply that provides 4.9V to the internal control circuitry and gate drivers, with a decoupling capacitor placed close to this pin.
17 AGND power_in Analog ground for the regulator control circuitry.
18 FB input Feedback input with a 0.815V threshold; for the adjustable version it connects to the resistor divider center point, and for the fixed version it connects directly to the output.
19 SS input Soft start input where a capacitor from SS to GND sets the soft-start time, with the MPQ4317 sourcing 13µA into the soft-start capacitor at start-up.
20 FREQ input Switching frequency program pin where a resistor from this pin to ground sets the switching frequency fSW.
21 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Monolithic Power Systems
Package QFN-20(4x4)
Category Power Management
Pins 21

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
VIN and EN voltage -0.3 50 V 5
SW voltage -0.3 V max VIN(MAX) + 0.3V 5
BST voltage 5.5 V referenced to VSW (VSW + 5.5V) 5
All other pins voltage -0.3 5.5 V 5
Continuous power dissipation PD 5.4 W TA = 25°C, QFN-20 (4mmx4mm) 5
Operating junction temperature TJ 150 °C 5
Storage temperature -65 150 °C 5
ESD human body model HBM -2 2 kV 5
ESD charged device model CDM -750 750 V 5
Supply voltage VIN 3.3 45 V 5
Output voltage VOUT 0.815 V upper limit 0.95 x VIN 5
Operating junction temperature TJ -40 150 °C 5
VIN UVLO rising threshold INUVLO_RISING 2.8 3 3.2 V 6
VCC voltage VCC 4.6 4.9 5.2 V IVCC = 0A 6
VCC regulation 1 4 % IVCC = 30mA 6
VIN quiescent current (sleep mode) IQ 18 26 µA FB = 0.85V, no load, (sleep mode) 6
VIN shutdown current ISHDN 1.7 3.5 µA EN = 0V 6
FB reference voltage VFB 807 815 823 mV VIN = 3.3V to 45V, TJ = 25°C 6
FB reference voltage VFB 799 815 831 mV VIN = 3.3V to 45V 6
FB current IFB -50 0 50 nA VFB = 0.85V, adjustable-output version 6
Switching frequency fSW 420 470 520 kHz RFREQ = 62kΩ 6
Switching frequency fSW 820 1000 1180 kHz RFREQ = 26.1kΩ 6
SYNCIN clock range fSYNC 350 1000 kHz External clock 6
SYNCO high voltage VSYNCO_HIGH 3.3 4.5 V ISYNCO = -1mA 6
High-side current limit ILIMIT 10 13 16 A Duty cycle = 30% 6
Low-side valley current limit ILIMIT_VALLEY 8 10 12 A 6
Zero-current detection current IZCD -0.15 0.1 0.35 A AAM 7
LS reverse current limit ILIMIT_REVERSE 2 4.5 7 A FCCM 7
Switch leakage current ISW_LKG 0.01 1 µA 7
HS-FET on resistance RON_HS 48 80 mΩ VBST - VSW = 5V 7
LS-FET on resistance RON_LS 20 40 mΩ VCC = 5V 7
Soft-start current ISS 8 13 19 µA VSS = 0V 7
EN rising threshold VEN_RISING 0.8 1 1.2 V 7
EN falling threshold VEN_FALLING 0.65 0.85 1.05 V 7
PG rising threshold (VFB/VREF) PGRISING 92 95 98 % VFB rising 7
PG rising threshold (VFB/VREF) PGRISING 102 105 108 % VFB falling 7
PG falling threshold (VFB/VREF) PGFALLING 90.5 93.5 96.5 % VFB falling 7
PG falling threshold (VFB/VREF) PGFALLING 103.5 106.5 109.5 % VFB rising 7
PG output voltage low VPG_LOW 0.1 0.3 V ISINK = 1mA 7
VCC current limit ILIMIT_VCC 100 mA VCC = 4V 6
VIN quiescent current (switching, AAM) IQ_ACTIVE 20 µA MODE = GND (AAM), switching, no load, RFB_UP = 1MΩ, RFB_DOWN = 324kΩ 6
VIN quiescent current (switching, FCCM) IQ_ACTIVE 40 mA MODE = HIGH (FCCM), switching, fSW = 2MHz, no load 6
VIN quiescent current (switching, FCCM) IQ_ACTIVE 9.5 mA MODE = HIGH(FCCM), switching, fSW = 470kHz, no load 6
Minimum on time tON_MIN 100 ns 6
Minimum off time tOFF_MIN 80 ns 6
SYNCIN voltage rising threshold VSYNC_RISING 1.8 V 6
SYNCIN voltage falling threshold VSYNC_FALLING 0.4 V 6
SYNCO low voltage VSYNCO_LOW 0.4 V ISYNCO = 1mA 6
MODE rising threshold VMODE_RISING 1.8 V 7
MODE falling threshold VMODE_FALLING 0.4 V 7
Thermal shutdown TSD 170 C 7
Thermal shutdown hysteresis TSD_HYS 20 °C 7
Thermal resistance junction-to-case QFN-20 θJC 9 °C/W 5

CAD (KiCad official)

  • Symbol: MPQ4317GRE-AEC1-Z
  • Footprint: Package_DFN_QFN:QFN-20-1EP_4x4mm_P0.5mm_EP2.5x2.5mm
  • 3D model: QFN-20(4x4) (KiCad packages3D, STEP)
  • 3D model files: mpq4317gre-aec1-z-etched.step / mpq4317gre-aec1-z-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); mpq4317gre-aec1-z.step / mpq4317gre-aec1-z.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Monolithic Power Systems datasheet (39 pp, sha256 0af503cd3cf43499, retrieved 2026-10-27, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus off (skipped (clean text read)), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF