main
Ray Publish 0.1.0 d6c8dbf

MPQ4316GRE-AEC1-Z

Monolithic Power Systems · DC-DC Converters · QFN-20(4x4)

MPQ4316GRE-AEC1-Z from Monolithic Power Systems, in a QFN-20(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 MODE input AAM or FCCM selection pin: pull high to force forced continuous conduction mode (FCCM), pull low to force advanced asynchronous mode (AAM) under light loads, and do not float it.
2 SYNCIN input SYNC input that accepts a 350kHz to 1000kHz clock to synchronize the internal oscillator, has an internal high impedance, and must not be left floating.
3 VIN power_in Input supply that powers the internal control circuitry and the power switch connected to SW, with a decoupling capacitor to ground placed close to VIN.
4 PGND power_in Power ground.
5 PGND power_in Power ground.
6 BST passive Bootstrap positive supply for the high-side MOSFET driver connected to SW, requiring a bypass capacitor between BST and SW.
7 SW output Switch node, the output of the internal power switch.
8 SW output Switch node, the output of the internal power switch.
9 EN input Enable pin: pull below the 0.85V threshold to shut down the chip and above the 1V threshold to enable it.
10 PGND power_in Power ground.
11 PGND power_in Power ground.
12 VIN power_in Input supply that powers the internal control circuitry and the power switch connected to SW, with a decoupling capacitor to ground placed close to VIN.
13 SYNCO output SYNC output that outputs a clock 180° out of phase with the internal oscillator, and should be left floating if not used.
14 PG output Open-drain power good output that goes high when VOUT is within 95% to 105% of nominal and low above 106.5% or below 93%, requiring a pull-up resistor.
15 NC unconnected Not connected; float if not used.
16 VCC power_out Bias supply that supplies 4.9V to the internal control circuit and gate drivers, with a decoupling capacitor placed close to VCC.
17 AGND power_in Analog ground.
18 FB input Feedback input with a feedback threshold voltage of about 0.815V, where the resistor divider must be placed as close to FB as possible.
19 SS input Soft-start input where a capacitor from SS to GND sets the soft-start period, and the device sources 13µA into the soft-start capacitor at start-up.
20 FREQ input Switching frequency configuration: a resistor from FREQ to ground sets the switching frequency fSW.
21 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Monolithic Power Systems
Package QFN-20(4x4)
Category Power Supply Chip
Pins 21

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
VIN UVLO rising threshold INUVLO_RISING 2.8 3 3.2 V 6
VIN UVLO falling threshold INUVLO_FALLING 2.5 2.7 2.9 V 6
VCC voltage VCC 4.6 4.9 5.2 V IVCC = 0A 6
VCC regulation 1 4 % IVCC = 30mA 6
VCC current limit ILIMIT_VCC 100 mA VCC = 4V 6
VIN quiescent current (sleep mode) IQ 18 26 μA FB = 0.85V, no load, (sleep mode) 6
VIN quiescent current (switching, AAM) IQ_ACTIVE 20 μA MODE = GND (AAM), switching, no load, RFB_UP = 1MΩ, RFB_DOWN = 324kΩ 6
VIN quiescent current (switching, FCCM, 2MHz) IQ_ACTIVE 40 mA MODE = high (FCCM), switching, fSW = 2MHz, no load 6
VIN quiescent current (switching, FCCM, 470kHz) IQ_ACTIVE 9.5 mA MODE = high (FCCM), switching, fSW = 470kHz, no load 6
VIN shutdown current ISHDN 1.7 3.5 μA EN=0V 6
FB reference voltage VFB 0.807 0.815 0.823 V VIN = 3.3V to 45V, TJ = 25°C 6
FB reference voltage VFB 0.799 0.815 0.831 V VIN = 3.3V to 45V 6
FB current IFB -50 0 50 nA VFB = 0.85V, adjustable output version 6
Switching frequency fSW 420 470 520 kHz RFREQ = 62kΩ 6
Switching frequency fSW 820 1000 1180 kHz RFREQ = 26.1kΩ 6
Minimum on time tON_MIN 100 ns 6
Minimum off time tOFF_MIN 80 ns 6
SYNCIN voltage rising threshold VSYNC_RISING 1.8 V 6
SYNCIN voltage falling threshold VSYNC_FALLING 0.4 V 6
SYNCIN clock range fSYNC 350 1000 kHz External clock 6
SYNCO high voltage VSYNCO_HIGH 3.3 4.5 V ISYNCO = -1mA 6
SYNCO low voltage VSYNCO_LOW 0.4 V ISYNCO = 1mA 6
SYNCO phase shift 180 Deg Tested under SYNCIN 6
HS current limit ILIMIT 10 13 16 A Duty cycle = 30% 6
LS valley current limit ILIMIT_VALLEY 8 10 12 A 6
ZCD current IZCD -0.15 0.1 0.35 A AAM 7
LS reverse current limit ILIMIT_REVERSE 2 4.5 7 A FCCM 7
Switch leakage current ISW_LKG 0.01 1 µA 7
HS switch on resistance RON(HS) 48 80 mΩ VBST - VSW = 5V 7
LS switch on resistance RON(LS) 20 40 mΩ VCC = 5V 7
Soft-start current ISS 8 13 19 µA VSS = 0V 7
EN rising threshold VEN_RISING 0.8 1 1.2 V 7
EN falling threshold VEN_FALLING 0.65 0.85 1.05 V 7
EN hysteresis voltage VEN_HYS 190 mV 7
MODE rising threshold VMODE_RISING 1.8 V 7
MODE falling threshold VMODE_FALLING 0.4 V 7
PG rising threshold (VFB/VREF) PGRISING 92 95 98 % VFB rising 7
PG rising threshold (VFB/VREF) PGRISING 102 105 108 % VFB falling 7
PG falling threshold (VFB/VREF) PGFALLING 90.5 93.5 96.5 % VFB falling 7
PG falling threshold (VFB/VREF) PGFALLING 103.5 106.5 109.5 % VFB rising 7
PG output voltage low VPG_LOW 0.1 0.3 V ISINK = 1mA 7
PG rising delay tPG_R_DELAY 35 µs 7
PG falling delay tPG_F_DELAY 35 µs 7
Thermal shutdown TSD 170 °C 7
Thermal shutdown hysteresis TSD_HYS 20 °C 7
VIN, EN voltage -0.3 50 V 5
All other pins voltage -0.3 5.5 V 5
Continuous power dissipation PD 5.4 W TA = 25°C, QFN-20 (4mmx4mm) 5
Operating junction temperature TJ 150 °C 5
Lead temperature 260 °C 5
Storage temperature TSTG -65 150 °C 5
ESD human body model (HBM) -2 2 kV 5
ESD charged device model (CDM) -750 750 V 5
Supply voltage VIN 3.3 45 V 5
Operating junction temperature TJ -40 150 °C 5
Thermal resistance junction-to-case θJC 9 °C/W QFN-20 (4mmx4mm) 5

CAD (KiCad official)

  • Symbol: MPQ4316GRE-AEC1-Z
  • Footprint: Package_DFN_QFN:QFN-20-1EP_4x4mm_P0.5mm_EP2.5x2.5mm
  • 3D model: QFN-20(4x4) (KiCad packages3D, STEP)
  • 3D model files: mpq4316gre-aec1-z-etched.step / mpq4316gre-aec1-z-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); mpq4316gre-aec1-z.step / mpq4316gre-aec1-z.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Monolithic Power Systems datasheet (39 pp, sha256 c37c2e1023e18ae5, retrieved 2026-10-26, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF