main
Ray Publish 0.1.0 a580266

MPQ4312GRE-AEC1-Z

Monolithic Power Systems · DC-DC Converters · QFN-20(4x4)

MPQ4312GRE-AEC1-Z from Monolithic Power Systems, in a QFN-20(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 MODE input AAM or FCCM selection pin: pull high for forced continuous conduction mode (FCCM), pull low for advanced asynchronous modulation (AAM) at light load; do not float this pin.
2 SYNCIN input SYNC input that accepts a 350kHz to 1000kHz clock to synchronize the internal oscillator, also used for multi-phase operation; internally high impedance, never float, and a ≤51kΩ resistor to GND is recommended.
3 VIN power_in Input supply (3.3V to 45V) for all internal control circuitry and the power MOSFET connected to SW, with a decoupling capacitor to ground placed as close as possible.
4 PGND power_in Power ground.
5 PGND power_in Power ground.
6 BST passive Bootstrap positive supply for the high-side MOSFET driver, with a bypass capacitor connected between BST and SW.
7 SW power_out Switch node, the output of the internal power MOSFET.
8 SW power_out Switch node, the output of the internal power MOSFET.
9 EN input Enable pin: pull below 0.85V to shut down the chip, pull above 1V to enable it.
10 PGND power_in Power ground.
11 PGND power_in Power ground.
12 VIN power_in Input supply (3.3V to 45V) for all internal control circuitry and the power MOSFET connected to SW, with a decoupling capacitor to ground placed as close as possible.
13 SYNCO output SYNC output giving a clock 180° out of phase with the internal oscillator (or opposite to the SYNCIN clock); float if not used.
14 PG output Open-drain power good output that goes high when VOUT is within 95% to 105% of nominal and low above 106.5% or below 93%; requires a pull-up resistor.
15 NC unconnected Not connected; float this pin.
16 VCC power_out Bias supply for the internal control circuitry and gate drivers, requiring a decoupling capacitor to ground placed close to the pin.
17 AGND power_in Analog ground.
18 FB input Feedback input connected to the midpoint of the external resistor divider between output and AGND, with a feedback threshold voltage of 0.815V.
19 SS passive Soft-start input: a capacitor to GND sets the soft-start time, with 13µA sourced into the capacitor during start-up.
20 FREQ passive Switching frequency selection: a resistor from this pin to ground sets the switching frequency (fSW).
21 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Monolithic Power Systems
Package QFN-20(4x4)
Category Power Supply Chip
Pins 21

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
VIN, EN voltage VIN, EN -0.3 50 V 5
SW voltage VSW -0.3 V -0.3V to VIN(MAX)+0.3V 5
BST voltage VBST 5.5 V VSW + 5.5V (relative to SW) 5
All other pins -0.3 5.5 V 5
Operating junction temperature TJ 150 °C 5
Storage temperature TSTG -65 150 °C 5
ESD HBM -2 2 kV Human body model 5
ESD CDM -750 750 V Charged device model 5
Supply voltage VIN 3.3 45 V 5
Output voltage VOUT 0.815 V 0.815V to 0.95 x VIN 5
Operating junction temperature TJ -40 150 °C 5
Junction-to-case thermal resistance θJC 9 °C/W JESD51-7 5
Junction-to-ambient thermal resistance θJA 23 °C/W EVQ4312-R-00A 5
Junction-to-case thermal resistance θJC 2.5 °C/W EVQ4312-R-00A 5
VIN UVLO rising threshold VIN_UVLO_RISING 2.8 3 3.2 V 6
VIN UVLO falling threshold VIN_UVLO_FALLING 2.5 2.7 2.9 V 6
VIN UVLO hysteresis VIN_UVLO_HYS 280 mV 6
VCC voltage VCC 4.6 4.9 5.2 V IVCC = 0A 6
VCC current limit ILIMIT_VCC 100 mA VCC = 4V 6
VIN quiescent current IQ 18 26 μA FB = 0.85V, no load, (sleep mode) 6
VIN quiescent current (switching) IQ_ACTIVE 20 μA MODE = GND (AAM), switching, no load, RFB_UP = 1MΩ, RFB_DOWN = 316kΩ 6
VIN quiescent current (switching) IQ_ACTIVE 40 mA MODE = high (FCCM), switching, fSW = 2MHz, no load 6
VIN quiescent current (switching) IQ_ACTIVE 9.5 mA MODE = high (FCCM), switching, fSW = 470kHz, no load 6
VIN shutdown current ISHDN 1.7 3.5 μA EN = 0V 6
FB reference voltage VFB 0.807 0.815 0.823 V VIN = 3.3V to 45V, TJ = 25°C 6
FB reference voltage VFB 0.799 0.815 0.831 V VIN = 3.3V to 45V 6
FB current IFB -50 0 50 nA VFB = 0.85V 6
Switching frequency fSW 420 470 520 kHz RFREQ = 62kΩ 6
Switching frequency fSW 820 1000 1180 kHz RFREQ = 26.1kΩ 6
Minimum on time tON_MIN 100 ns 6
Minimum off time tOFF_MIN 80 ns 6
SYNCIN clock range fSYNC 350 1000 kHz External clock 6
SYNCO phase shift 180 deg Tested under SYNCIN 6
High-side current limit ILIMIT 4.4 5.5 6.6 A Duty cycle = 30% 6
Low-side valley current limit ILIMIT_VALLEY 3.2 4 4.8 A 6
Zero-current detection current IZCD -0.15 0.1 0.35 A AAM 7
LS reverse current limit ILIMIT_REVERSE 2 4.5 7 A FCCM 7
Switch leakage current ISW_LKG 0.01 1 µA 7
HS-FET on resistance RDS(ON)_HS 48 80 mΩ VBST - VSW = 5V 7
LS-FET on resistance RDS(ON)_LS 20 40 mΩ VCC = 5V 7
Soft-start current ISS 8 13 19 µA VSS = 0V 7
EN rising threshold VEN_RISING 0.8 1 1.2 V 7
EN falling threshold VEN_FALLING 0.65 0.85 1.05 V 7
EN hysteresis voltage VEN_HYS 190 mV 7
PG rising threshold (lower) PGRISING 92 95 98 % VREF VFB rising 7
PG rising threshold (upper) PGRISING 102 105 108 % VREF VFB falling 7
PG falling threshold (lower) PGFALLING 90.5 93.5 96.5 % VREF VFB falling 7
PG falling threshold (upper) PGFALLING 103.5 106.5 109.5 % VREF VFB rising 7
PG output voltage low VPG_LOW 0.1 0.3 V ISINK = 1mA 7
PG rising delay tPG_R_DELAY 35 µs 7
PG falling delay tPG_F_DELAY 35 µs 7
Thermal shutdown TSD 170 °C 7
Thermal shutdown hysteresis TSD_HYS 20 °C 7

CAD (KiCad official)

  • Symbol: MPQ4312GRE-AEC1-Z
  • Footprint: Package_DFN_QFN:QFN-20-1EP_4x4mm_P0.5mm_EP2.5x2.5mm
  • 3D model: QFN-20(4x4) (KiCad packages3D, STEP)
  • 3D model files: mpq4312gre-aec1-z-etched.step / mpq4312gre-aec1-z-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); mpq4312gre-aec1-z.step / mpq4312gre-aec1-z.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Monolithic Power Systems datasheet (37 pp, sha256 460020cb98f192ae, retrieved 2026-10-26, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF