main
Ray
Publish 0.1.0
ddb607c
MPQ3364GR-AEC1-Z
Monolithic Power Systems · LED Drivers · QFN-24(4x4)
MPQ3364GR-AEC1-Z from Monolithic Power Systems, in a QFN-24(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | DIM | input | PWM signal input for brightness control, pulled low internally, with a 100Hz to 20kHz PWM signal recommended. |
| 2 | MIX/AD | passive | Dimming mode setting pin with an 18uA current-source output where a resistor sets the voltage: <0.3V mix dimming, 0.5V to 0.8V PWM dimming, 1.0V to 1.3V analog dimming, floating selects the MODE register setting. |
| 3 | FREQ/SYNC | input | Switching frequency setting pin using a resistor to GND or an external clock for synchronization, floated if the frequency is set by FSW1:0. |
| 4 | EN | input | IC enable pin, pulled high to enable the IC and low to shut it down. |
| 5 | SCL/PSE | input | I2C clock input; connected to SDA/PSE and pulled up between 0.75V and 1V to enable phase shift PWM dimming, pulled to GND if unused and must not float. |
| 6 | SDA/PSE | input | I2C data input; connected to SCL/PSE and pulled up between 0.75V and 1V to enable phase shift PWM dimming, pulled to GND if unused and must not float. |
| 7 | COMP | passive | Compensation pin. |
| 8 | FF | output | Fault flag pin that is open drain during normal operation and pulled low if a fault occurs. |
| 9 | ISET | passive | LED current setting pin with a current-setting resistor from ISET to GND to configure the current in each LED string. |
| 10 | AGND | power_in | Analog ground. |
| 11 | AGND | power_in | Analog ground. |
| 12 | AGND | power_in | Analog ground. |
| 13 | LED4 | input | LED string 4 current input, connected to the LED string 4 cathode. |
| 14 | LED3 | input | LED string 3 current input, connected to the LED string 3 cathode. |
| 15 | LED2 | input | LED string 2 current input, connected to the LED string 2 cathode. |
| 16 | LED1 | input | LED string 1 current input, connected to the LED string 1 cathode. |
| 17 | PGND | power_in | Step-up converter power ground. |
| 18 | SW | passive | Drain of the internal low-side MOSFET switch, connected to the power inductor. |
| 19 | OVP | input | Over-voltage protection pin with a resistor divider from OVP to GND to set the over-voltage protection threshold. |
| 20 | STH | passive | Short LED protection threshold setting pin with an 18uA current-source output where a resistor sets the voltage, floated if the threshold is set by TH_S1:0. |
| 21 | ADR | passive | IC address setting pin using a resistor with an 18uA pull-up current: floating gives address 0x38, <0.4V gives 0x3A, 0.4V to 1.4V gives 0x39. |
| 22 | VCC | power_out | 5V LDO output powering the internal logic and gate driver, with a ceramic capacitor placed as close to the pin as possible. |
| 23 | SD | output | Gate drive pin for the external disconnect P-channel MOSFET, turning it off if a fault occurs and floated if unused. |
| 24 | VIN | power_in | Power supply input that supplies power to the IC. |
| 25 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Monolithic Power Systems |
| Package | QFN-24(4x4) |
| Category | Nixie Tube Driver/LED Driver |
| Pins | 25 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage VIN | VIN | -0.3 | 42 | V | 6 | ||
| Switch and LED pin voltage | VSW, VLED1 to VLED4 | -0.5 | 50 | V | 6 | ||
| Switch transient voltage | VSW | -1 | V | for <100ns | 6 | ||
| All other pins voltage | -0.3 | 6 | V | 6 | |||
| Junction temperature | TJ | 150 | °C | 6 | |||
| Storage temperature | -65 | 150 | °C | 6 | |||
| ESD HBM LED1~4 | -7 | 7 | kV | HBM, LED1~4 | 6 | ||
| ESD HBM all other pins | -4 | 4 | kV | HBM, all other pins | 6 | ||
| ESD charged device model | -2 | 2 | kV | CDM | 6 | ||
| Supply voltage VIN | VIN | 3.5 | 36 | V | 6 | ||
| Operating junction temperature | TJ | -40 | 125 | °C | 6 | ||
| Thermal resistance junction-to-ambient | θJA | 42 | °C/W | QFN-24 (4mmx4mm), JESD51-7 4-layer PCB | 6 | ||
| Switching frequency | fSW | 1.98 | 2.2 | 2.42 | MHz | RFREQ = 10kΩ | 7 |
| Switching frequency | fSW | 495 | 550 | 605 | kHz | RFREQ = 40kΩ | 7 |
| Switching frequency | fSW | 340 | 400 | 460 | kHz | FSW1:0 = 01, FREQ floating | 7 |
| FREQ voltage | VFREQ | 0.57 | 0.6 | 0.63 | V | 7 | |
| Cycle-by-cycle current limiting | ISW_LIMIT | 5.5 | 7 | A | TJ = +25°C and -40°C, Duty = 90% | 7 | |
| Cycle-by-cycle current limiting | ISW_LIMIT | 4.5 | 5.5 | A | TJ = 125°C, duty = 90% | 7 | |
| PSE active threshold | VPSE | 0.75 | 0.9 | 1 | V | Phase shift enabled | 7 |
| MIX/AD input middle threshold | VMIX_MID | 0.5 | 0.8 | V | PWM dimming threshold | 7 | |
| MIX/AD input high threshold | VMIX_HI | 1 | 1.3 | V | Analog dimming threshold | 7 | |
| Current matching | -2.5 | 2.5 | % | ILED = 20mA | 8 | ||
| LED current | ILED | 48.75 | 50 | 51.25 | mA | RISET = 24.9kΩ, TJ = 25°C | 8 |
| LED current | ILED | 0.9 | 1.05 | 1.2 | mA | ILED = 1 / 50 x 50mA = 1mA | 8 |
| Over-voltage protection threshold | VOVP | 1.9 | 2 | 2.1 | V | 8 | |
| LEDx regulation voltage | VHD | 850 | 1000 | mV | ILED = 100mA | 8 | |
| Quiescent supply current | IQ | 5 | mA | No switching | 7 | ||
| Shutdown supply current | IST | 1 | μA | VEN = 0V, VIN = 12V | 7 | ||
| Input UVLO threshold | VIN_UVLO | 3.1 | V | Rising edge | 7 | ||
| Input UVLO hysteresis | 100 | mV | 7 | ||||
| LDO output voltage | VCC | 5 | V | VEN = 2V, 6V < VIN < 24V, 0mA < IVCC < 10mA | 7 | ||
| EN on threshold | VEN_ON | 1.2 | V | VEN rising | 7 | ||
| EN off threshold | VEN_OFF | 0.4 | V | VEN falling | 7 | ||
| Low-side MOSFET on resistance | RDS(ON)_LS | 100 | mΩ | VIN = 12V | 7 | ||
| Maximum duty cycle | DMAX | 90 | % | fSW = 1MHz | 7 | ||
| Current limit protection | ICL | 12 | A | To trigger current limit protection | 7 | ||
| SYNC input low threshold | VSYNC_LO | 0.4 | V | VSYNC falling | 7 | ||
| SYNC input high threshold | VSYNC_HI | 1.2 | V | VSYNC rising | 7 | ||
| COMP trans-conductance | GCOMP | 100 | μA/V | ΔICOMP ≤ 10μA | 7 | ||
| DIM input low threshold | VDIM_LO | 0.4 | V | VDIM falling | 7 | ||
| DIM input high threshold | VDIM_HI | 1.2 | V | VDIM rising | 7 | ||
| MIX/AD input low threshold | VMIX_LO | 0.3 | V | Mix dimming threshold | 7 | ||
| Mix dimming transfer point | MIXTP | 25 | % | MIXTP bit = 0 | 8 | ||
| Transfer point hysteresis | 0.5 | % | 8 | ||||
| Mix dimming output dimming frequency | fMIX | 200 | Hz | MIXFR bit = 0 | 8 | ||
| LEDx regulation voltage | VHD | 350 | mV | ILED = 20mA | 8 | ||
| Phase shift degree | 90 | ° | LED1 to 4 enable | 8 | |||
| OVP hysteresis | 200 | mV | 8 | ||||
| OVP UVLO threshold | VOVP_UV | 100 | mV | Step-up converter fails | 8 | ||
| LEDx over-voltage threshold | VLEDX_OV | 5 | V | LEDx bits = 01 | 8 | ||
| LEDx UVLO threshold | VLEDX_UV | 100 | mV | 8 | |||
| Thermal shutdown threshold rising edge | TST | 170 | °C | Rising edge, guaranteed by design | 8 | ||
| Thermal shutdown hysteresis | 20 | °C | Guaranteed by design | 8 | |||
| SD voltage relative to VIN | VSD-IN | 6 | V | VIN = 12V, VIN - VSD | 8 |
CAD (KiCad official)
- Symbol:
MPQ3364GR-AEC1-Z - Footprint:
Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm - 3D model: QFN-24(4x4) (KiCad packages3D, STEP)
- 3D model files:
mpq3364gr-aec1-z-etched.step/mpq3364gr-aec1-z-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mpq3364gr-aec1-z.step/mpq3364gr-aec1-z.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Monolithic Power Systems datasheet (27 pp, sha256
48716a936f3f0568, retrieved 2026-11-07, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# MPQ3364GR-AEC1-Z
**Monolithic Power Systems** · LED Drivers · QFN-24(4x4)
MPQ3364GR-AEC1-Z from Monolithic Power Systems, in a QFN-24(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | DIM | input | PWM signal input for brightness control, pulled low internally, with a 100Hz to 20kHz PWM signal recommended. |
| 2 | MIX/AD | passive | Dimming mode setting pin with an 18uA current-source output where a resistor sets the voltage: <0.3V mix dimming, 0.5V to 0.8V PWM dimming, 1.0V to 1.3V analog dimming, floating selects the MODE register setting. |
| 3 | FREQ/SYNC | input | Switching frequency setting pin using a resistor to GND or an external clock for synchronization, floated if the frequency is set by FSW1:0. |
| 4 | EN | input | IC enable pin, pulled high to enable the IC and low to shut it down. |
| 5 | SCL/PSE | input | I2C clock input; connected to SDA/PSE and pulled up between 0.75V and 1V to enable phase shift PWM dimming, pulled to GND if unused and must not float. |
| 6 | SDA/PSE | input | I2C data input; connected to SCL/PSE and pulled up between 0.75V and 1V to enable phase shift PWM dimming, pulled to GND if unused and must not float. |
| 7 | COMP | passive | Compensation pin. |
| 8 | FF | output | Fault flag pin that is open drain during normal operation and pulled low if a fault occurs. |
| 9 | ISET | passive | LED current setting pin with a current-setting resistor from ISET to GND to configure the current in each LED string. |
| 10 | AGND | power_in | Analog ground. |
| 11 | AGND | power_in | Analog ground. |
| 12 | AGND | power_in | Analog ground. |
| 13 | LED4 | input | LED string 4 current input, connected to the LED string 4 cathode. |
| 14 | LED3 | input | LED string 3 current input, connected to the LED string 3 cathode. |
| 15 | LED2 | input | LED string 2 current input, connected to the LED string 2 cathode. |
| 16 | LED1 | input | LED string 1 current input, connected to the LED string 1 cathode. |
| 17 | PGND | power_in | Step-up converter power ground. |
| 18 | SW | passive | Drain of the internal low-side MOSFET switch, connected to the power inductor. |
| 19 | OVP | input | Over-voltage protection pin with a resistor divider from OVP to GND to set the over-voltage protection threshold. |
| 20 | STH | passive | Short LED protection threshold setting pin with an 18uA current-source output where a resistor sets the voltage, floated if the threshold is set by TH_S1:0. |
| 21 | ADR | passive | IC address setting pin using a resistor with an 18uA pull-up current: floating gives address 0x38, <0.4V gives 0x3A, 0.4V to 1.4V gives 0x39. |
| 22 | VCC | power_out | 5V LDO output powering the internal logic and gate driver, with a ceramic capacitor placed as close to the pin as possible. |
| 23 | SD | output | Gate drive pin for the external disconnect P-channel MOSFET, turning it off if a fault occurs and floated if unused. |
| 24 | VIN | power_in | Power supply input that supplies power to the IC. |
| 25 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Monolithic Power Systems |
| Package | QFN-24(4x4) |
| Category | Nixie Tube Driver/LED Driver |
| Pins | 25 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage VIN | VIN | -0.3 | | 42 | V | | 6 |
| Switch and LED pin voltage | VSW, VLED1 to VLED4 | -0.5 | | 50 | V | | 6 |
| Switch transient voltage | VSW | -1 | | | V | for <100ns | 6 |
| All other pins voltage | | -0.3 | | 6 | V | | 6 |
| Junction temperature | TJ | | | 150 | °C | | 6 |
| Storage temperature | | -65 | | 150 | °C | | 6 |
| ESD HBM LED1~4 | | -7 | | 7 | kV | HBM, LED1~4 | 6 |
| ESD HBM all other pins | | -4 | | 4 | kV | HBM, all other pins | 6 |
| ESD charged device model | | -2 | | 2 | kV | CDM | 6 |
| Supply voltage VIN | VIN | 3.5 | | 36 | V | | 6 |
| Operating junction temperature | TJ | -40 | | 125 | °C | | 6 |
| Thermal resistance junction-to-ambient | θJA | | 42 | | °C/W | QFN-24 (4mmx4mm), JESD51-7 4-layer PCB | 6 |
| Switching frequency | fSW | 1.98 | 2.2 | 2.42 | MHz | RFREQ = 10kΩ | 7 |
| Switching frequency | fSW | 495 | 550 | 605 | kHz | RFREQ = 40kΩ | 7 |
| Switching frequency | fSW | 340 | 400 | 460 | kHz | FSW1:0 = 01, FREQ floating | 7 |
| FREQ voltage | VFREQ | 0.57 | 0.6 | 0.63 | V | | 7 |
| Cycle-by-cycle current limiting | ISW_LIMIT | 5.5 | | 7 | A | TJ = +25°C and -40°C, Duty = 90% | 7 |
| Cycle-by-cycle current limiting | ISW_LIMIT | 4.5 | | 5.5 | A | TJ = 125°C, duty = 90% | 7 |
| PSE active threshold | VPSE | 0.75 | 0.9 | 1 | V | Phase shift enabled | 7 |
| MIX/AD input middle threshold | VMIX_MID | 0.5 | | 0.8 | V | PWM dimming threshold | 7 |
| MIX/AD input high threshold | VMIX_HI | 1 | | 1.3 | V | Analog dimming threshold | 7 |
| Current matching | | -2.5 | | 2.5 | % | ILED = 20mA | 8 |
| LED current | ILED | 48.75 | 50 | 51.25 | mA | RISET = 24.9kΩ, TJ = 25°C | 8 |
| LED current | ILED | 0.9 | 1.05 | 1.2 | mA | ILED = 1 / 50 x 50mA = 1mA | 8 |
| Over-voltage protection threshold | VOVP | 1.9 | 2 | 2.1 | V | | 8 |
| LEDx regulation voltage | VHD | 850 | | 1000 | mV | ILED = 100mA | 8 |
| Quiescent supply current | IQ | | 5 | | mA | No switching | 7 |
| Shutdown supply current | IST | | 1 | | μA | VEN = 0V, VIN = 12V | 7 |
| Input UVLO threshold | VIN_UVLO | | 3.1 | | V | Rising edge | 7 |
| Input UVLO hysteresis | | | 100 | | mV | | 7 |
| LDO output voltage | VCC | | 5 | | V | VEN = 2V, 6V < VIN < 24V, 0mA < IVCC < 10mA | 7 |
| EN on threshold | VEN_ON | | 1.2 | | V | VEN rising | 7 |
| EN off threshold | VEN_OFF | | 0.4 | | V | VEN falling | 7 |
| Low-side MOSFET on resistance | RDS(ON)_LS | | 100 | | mΩ | VIN = 12V | 7 |
| Maximum duty cycle | DMAX | | 90 | | % | fSW = 1MHz | 7 |
| Current limit protection | ICL | | 12 | | A | To trigger current limit protection | 7 |
| SYNC input low threshold | VSYNC_LO | | 0.4 | | V | VSYNC falling | 7 |
| SYNC input high threshold | VSYNC_HI | | 1.2 | | V | VSYNC rising | 7 |
| COMP trans-conductance | GCOMP | | 100 | | μA/V | ΔICOMP ≤ 10μA | 7 |
| DIM input low threshold | VDIM_LO | | 0.4 | | V | VDIM falling | 7 |
| DIM input high threshold | VDIM_HI | | 1.2 | | V | VDIM rising | 7 |
| MIX/AD input low threshold | VMIX_LO | | 0.3 | | V | Mix dimming threshold | 7 |
| Mix dimming transfer point | MIXTP | | 25 | | % | MIXTP bit = 0 | 8 |
| Transfer point hysteresis | | | 0.5 | | % | | 8 |
| Mix dimming output dimming frequency | fMIX | | 200 | | Hz | MIXFR bit = 0 | 8 |
| LEDx regulation voltage | VHD | | 350 | | mV | ILED = 20mA | 8 |
| Phase shift degree | | | 90 | | ° | LED1 to 4 enable | 8 |
| OVP hysteresis | | | 200 | | mV | | 8 |
| OVP UVLO threshold | VOVP_UV | | 100 | | mV | Step-up converter fails | 8 |
| LEDx over-voltage threshold | VLEDX_OV | | 5 | | V | LEDx bits = 01 | 8 |
| LEDx UVLO threshold | VLEDX_UV | | 100 | | mV | | 8 |
| Thermal shutdown threshold rising edge | TST | | 170 | | °C | Rising edge, guaranteed by design | 8 |
| Thermal shutdown hysteresis | | | 20 | | °C | Guaranteed by design | 8 |
| SD voltage relative to VIN | VSD-IN | | 6 | | V | VIN = 12V, VIN - VSD | 8 |
## CAD (KiCad official)
- Symbol: `MPQ3364GR-AEC1-Z`
- Footprint: `Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm`
- 3D model: QFN-24(4x4) (KiCad packages3D, STEP)
- 3D model files: `mpq3364gr-aec1-z-etched.step` / `mpq3364gr-aec1-z-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `mpq3364gr-aec1-z.step` / `mpq3364gr-aec1-z.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Monolithic Power Systems datasheet](docs/mpq3364gr-aec1-z-datasheet.pdf) (27 pp, sha256 `48716a936f3f0568`, retrieved 2026-11-07, tier: lcsc)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/mpq3364gr-aec1-z-datasheet.pdf)