Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

MP8770GQ-Z

Monolithic Power Systems · DC-DC Converters · QFN-16(3x3)

MP8770GQ-Z from Monolithic Power Systems, in a QFN-16(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 NC unconnected No connection; NC must be left floating.
2 BST passive A capacitor between SW and BST forms the floating supply for the high-side driver, and a BST resistor below 4.7Ω is recommended.
3 EN input Enable input: drive above 1.25V to turn the regulator on and below 1V to turn it off; when floating it is pulled to GND by an internal 1.2MΩ resistor, and it supports a 17V input range.
4 FB input Feedback input, connected to the tap of an external resistor divider between the output and GND, which sets the output voltage against the 600mV reference.
5 AGND power_in Signal ground that is not internally connected to the system ground, so it must be tied to the system ground in the PCB layout.
6 SS passive Soft-start pin: a capacitor from SS to GND sets the soft-start time (6µA charging current), and SS capacitors below 4.7nF should be avoided.
7 PG output Open-drain power good output that is pulled low when UVP, OCP, OTP or OV occurs.
8 VIN power_in Supply voltage input operating from a 3V to 17V rail, which requires a decoupling capacitor C1 placed close to the pin.
9 PGND power_in System ground and reference ground of the regulated output voltage, recommended to be connected to GND with copper and vias.
10 PGND power_in System ground and reference ground of the regulated output voltage, recommended to be connected to GND with copper and vias.
11 PGND power_in System ground and reference ground of the regulated output voltage, recommended to be connected to GND with copper and vias.
12 PGND power_in System ground and reference ground of the regulated output voltage, recommended to be connected to GND with copper and vias.
13 PGND power_in System ground and reference ground of the regulated output voltage, recommended to be connected to GND with copper and vias.
14 VCC power_out Internal 3.4V bias supply output that must be decoupled with a 1µF capacitor placed close to VCC and GND.
15 NC unconnected No connection; NC must be left floating.
16 SW output Switch output node that should be connected with a wide PCB trace.
17 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Monolithic Power Systems
Package QFN-16(3x3)
Category Power Management
Pins 17

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input voltage range (VIN) supply voltage VIN 3 17 V 3
Operating junction temperature TJ -40 125 °C 3
Input voltage absolute maximum VIN -0.3 20 V 3
All other pins voltage -0.3 4 V All other pins 3
Switch node voltage VSW -0.3 V -5V < 10ns; to VIN + 0.7V (23V < 10ns) 3
Continuous power dissipation PD 3.2 W TA = +25°C 3
Junction temperature TJ 150 °C 3
Lead temperature 260 °C 3
Storage temperature -65 125 °C 3
Thermal resistance junction-to-ambient QFN-16 θJA 38 °C/W EV8770-Q-00A, 4-layer PCB 3
Thermal resistance junction-to-case QFN-16 θJC 10 °C/W EV8770-Q-00A, 4-layer PCB 3
Thermal resistance junction-to-ambient JESD51-7 θJA 50 °C/W JESD51-7 board 3
Thermal resistance junction-to-case JESD51-7 θJC 12 °C/W JESD51-7 board 3
Input voltage range VIN 3 17 V 4
Supply current (shutdown) IIN 5 µA VEN = 0V 4
Supply current (quiescent) IQ 100 150 µA VEN = 2V, VFB = 0.65V 4
HS switch on resistance HSRDS(ON) 22 mΩ VBST-SW = 3.3V 4
LS switch on resistance LSRDS(ON) 10 mΩ VCC = 3.3V 4
Switch leakage SWLKG 1 µA VEN = 0V, VSW = 17V, TJ = 25°C 4
Valley current limit ILIMIT_VY 8 10 A 4
Short hiccup duty cycle DHICCUP 10 % 4
ZCD current IZCD 200 mA 4
Switching frequency Fs 600 700 800 kHz 4
Minimum on time TOn MIN 50 ns 4
Minimum off time TOff MIN 100 ns 4
Feedback voltage VFB 594 600 606 mV TJ = 25°C 4
Feedback voltage VFB 591 600 609 mV TJ = -40°C to +125°C 4
Feedback current IFB 10 50 nA VFB = 700mV 4
Soft-start current ISS_START 4 6 8 µA 4
EN rising threshold VEN RISING 1.1 1.25 1.4 V 4
EN falling threshold VEN FALLING 0.9 1 1.1 V 4
EN pull-down resistor REN_PD 1.2 MΩ 4
VCC under-voltage lockout threshold rising VCCVth 2.6 2.8 3 V 4
VCC under-voltage lockout hysteresis VCCHYS 350 mV 4
VCC regulator output VCC 3.4 V 4
VCC load regulation RegVCC 3 % ICC = 5mA 4
Power good UV rising threshold PGUVvth_Hi 0.85 0.9 0.95 VFB 5
Power good UV falling threshold PGUVvth_Lo 0.75 0.8 0.85 VFB 5
Power good OV rising threshold PGOVvth_Hi 1.15 1.2 1.25 VFB 5
Power good OV falling threshold PGOVvth_Lo 1.05 1.1 1.15 VFB 5
Power good delay PGTd 50 µs Both edge 5
Power good sink voltage VPG 0.4 V Sink 4mA 5
Power good leakage current IPG_LEAK 10 µA VPG = 5V 5
Thermal shutdown TSD 150 °C 5
Thermal hysteresis TSD-HYS 20 °C 5

CAD (KiCad official)

  • Symbol: MP8770GQ-Z
  • Footprint: Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm
  • 3D model: QFN-16(3x3) (KiCad packages3D, STEP)
  • 3D model files: mp8770gq-z-etched.step / mp8770gq-z-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); mp8770gq-z.step / mp8770gq-z.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Monolithic Power Systems datasheet (23 pp, sha256 7437a523a9821a20, retrieved 2026-10-27, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus off (skipped (clean text read)), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF