main
Ray
Publish 0.1.0
9908765
MP8770CGQ-Z
Monolithic Power Systems · DC-DC Converters · QFN-16(3x3)
MP8770CGQ-Z from Monolithic Power Systems, in a QFN-16(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | NC | unconnected | No connection; the pin must be left floating. |
| 2 | BST | power_out | Bootstrap; a capacitor between SW and BS forms a floating supply for the high-side driver, and the BST resistor should be less than 4.7Ω. |
| 3 | EN | input | Enable; drive above 1.25V to turn the regulator on and below 1V to turn it off, with an internal 1.2MΩ pull-down to GND when floating and support for a 17V input range. |
| 4 | FB | input | Feedback; sets the output voltage when connected to the tap of an external resistor divider between output and GND, with a reference of 600mV. |
| 5 | AGND | power_in | Signal ground that is not internally connected to the system ground and must be tied to system ground in the PCB layout. |
| 6 | SS | passive | Soft start; a capacitor from SS to GND sets the soft-start time and avoids start-up inrush current, with an SS capacitor below 4.7nF to be avoided. |
| 7 | PG | output | Power good open-drain output that changes state if UVP, OCP, OTP, or OV occurs. |
| 8 | VIN | power_in | Supply voltage input operating from a 3V to 17V input rail, which must be decoupled with C1. |
| 9 | PGND | power_in | System ground and reference ground of the regulated output voltage, recommended to be connected to GND with copper pours and vias. |
| 10 | PGND | power_in | System ground and reference ground of the regulated output voltage, recommended to be connected to GND with copper pours and vias. |
| 11 | PGND | power_in | System ground and reference ground of the regulated output voltage, recommended to be connected to GND with copper pours and vias. |
| 12 | PGND | power_in | System ground and reference ground of the regulated output voltage, recommended to be connected to GND with copper pours and vias. |
| 13 | PGND | power_in | System ground and reference ground of the regulated output voltage, recommended to be connected to GND with copper pours and vias. |
| 14 | VCC | power_out | Internal bias supply output that must be decoupled with a 1µF capacitor placed close to the VCC and GND pins. |
| 15 | NC | unconnected | No connection; the pin must be left floating. |
| 16 | SW | output | Switch output that requires a wide PCB trace for the connection. |
| 17 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Monolithic Power Systems |
| Package | QFN-16(3x3) |
| Category | Power Supply Chip |
| Pins | 17 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage range | VIN | 3 | 17 | V | 4 | ||
| Valley current limit | ILIMIT_VY | 8 | 10 | A | 4 | ||
| Feedback current | IFB | 10 | 50 | nA | VFB = 700mV | 4 | |
| Switching frequency | fSW | 600 | 700 | 800 | kHz | 4 | |
| Feedback voltage TJ = 25°C | VFB | 594 | 600 | 606 | mV | TJ = 25°C | 4 |
| Feedback voltage TJ = -40°C to +125°C | VFB | 591 | 600 | 609 | mV | TJ = -40°C to +125°C | 4 |
| Soft-start current | ISS_START | 4 | 6 | 8 | µA | 4 | |
| EN rising threshold | VEN RISING | 1.1 | 1.25 | 1.4 | V | 4 | |
| EN falling threshold | VEN FALLING | 0.9 | 1 | 1.1 | V | 4 | |
| VCC under-voltage lockout rising threshold | VCCVth | 2.6 | 2.8 | 3 | V | 4 | |
| Supply current quiescent | IQ | 100 | 150 | µA | VEN = 2V, VFB = 0.65V | 4 | |
| Supply current shutdown | IIN | 5 | µA | VEN = 0V | 4 | ||
| Switch leakage | SWLKG | 1 | µA | VEN = 0V, VSW = 17V | 4 | ||
| VCC under-voltage lockout threshold | VCCHYS | 350 | mV | 4 | |||
| VCC load regulation | RegVCC | 3 | % | ICC = 5mA | 4 | ||
| Power good UV rising threshold | PGUVvth_Hi | 0.85 | 0.9 | 0.95 | VFB | 5 | |
| Power good UV falling threshold | PGUVvth_Lo | 0.75 | 0.8 | 0.85 | VFB | 5 | |
| Power good OV rising threshold | PGOVvth_Hi | 1.15 | 1.2 | 1.25 | VFB | 5 | |
| Power good OV falling threshold | PGOVvth_Lo | 1.05 | 1.1 | 1.15 | VFB | 5 | |
| Input voltage absolute maximum | VIN | -0.3 | 20 | V | 3 | ||
| Voltage on all other pins | -0.3 | 4 | V | All other pins | 3 | ||
| Junction temperature | TJ | 150 | °C | 3 | |||
| Storage temperature | TSTORE | -65 | 125 | °C | 3 | ||
| Supply voltage | VIN | 3 | 17 | V | 3 | ||
| Output voltage | VOUT | 0.6 | 12 | V | Upper limit is VIN*DMAX or 12V max | 3 | |
| Operating junction temperature | TJ | -40 | 125 | °C | 3 | ||
| Thermal resistance junction-to-case | θJC | 10 | °C/W | QFN-16, measured on EV8770C-Q-00A 4-layer PCB | 3 | ||
| Thermal resistance junction-to-ambient (JESD51-7 board) | θJA | 50 | °C/W | JESD51-7 board | 3 | ||
| Thermal resistance junction-to-case (JESD51-7 board) | θJC | 12 | °C/W | JESD51-7 board | 3 | ||
| HS switch on resistance | HSRDS-ON | 22 | mΩ | VBST-SW = 3.3V | 4 | ||
| LS switch on resistance | LSRDS-ON | 10 | mΩ | VCC = 3.3V | 4 | ||
| Short hiccup duty cycle | DHICCUP | 10 | % | 4 | |||
| Minimum on time | tON_MIN | 50 | ns | 4 | |||
| Minimum off time | tOFF_MIN | 100 | ns | 4 | |||
| EN pin pull-down resistor | REN_PD | 1.2 | MΩ | 4 | |||
| VCC regulator | VCC | 3.4 | V | 4 | |||
| Power good delay | PGTd | 50 | µs | Both edge | 5 | ||
| Power good sink current capability | VPG Sink | 0.4 | V | Sink 4mA | 5 | ||
| Power good leakage current | IPG_LEAK | 10 | µA | VPG = 5V | 5 | ||
| Thermal shutdown | TSD | 150 | °C | 5 | |||
| Thermal hysteresis | TSD-HYS | 20 | °C | 5 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | System ground. This pin is the reference ground of the regulated output voltage, so care must be taken during PCB layout. It is recommended to connect it to GND with copper pours | 3 |
CAD (KiCad official)
- Symbol:
MP8770CGQ-Z - Footprint:
Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm - 3D model: QFN-16(3x3) (KiCad packages3D, STEP)
- 3D model files:
mp8770cgq-z-etched.step/mp8770cgq-z-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mp8770cgq-z.step/mp8770cgq-z.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Monolithic Power Systems datasheet, copy hosted by LCSC (23 pp, sha256
341e02dfba84eade, retrieved 2026-11-21) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# MP8770CGQ-Z
**Monolithic Power Systems** · DC-DC Converters · QFN-16(3x3)
MP8770CGQ-Z from Monolithic Power Systems, in a QFN-16(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | NC | unconnected | No connection; the pin must be left floating. |
| 2 | BST | power_out | Bootstrap; a capacitor between SW and BS forms a floating supply for the high-side driver, and the BST resistor should be less than 4.7Ω. |
| 3 | EN | input | Enable; drive above 1.25V to turn the regulator on and below 1V to turn it off, with an internal 1.2MΩ pull-down to GND when floating and support for a 17V input range. |
| 4 | FB | input | Feedback; sets the output voltage when connected to the tap of an external resistor divider between output and GND, with a reference of 600mV. |
| 5 | AGND | power_in | Signal ground that is not internally connected to the system ground and must be tied to system ground in the PCB layout. |
| 6 | SS | passive | Soft start; a capacitor from SS to GND sets the soft-start time and avoids start-up inrush current, with an SS capacitor below 4.7nF to be avoided. |
| 7 | PG | output | Power good open-drain output that changes state if UVP, OCP, OTP, or OV occurs. |
| 8 | VIN | power_in | Supply voltage input operating from a 3V to 17V input rail, which must be decoupled with C1. |
| 9 | PGND | power_in | System ground and reference ground of the regulated output voltage, recommended to be connected to GND with copper pours and vias. |
| 10 | PGND | power_in | System ground and reference ground of the regulated output voltage, recommended to be connected to GND with copper pours and vias. |
| 11 | PGND | power_in | System ground and reference ground of the regulated output voltage, recommended to be connected to GND with copper pours and vias. |
| 12 | PGND | power_in | System ground and reference ground of the regulated output voltage, recommended to be connected to GND with copper pours and vias. |
| 13 | PGND | power_in | System ground and reference ground of the regulated output voltage, recommended to be connected to GND with copper pours and vias. |
| 14 | VCC | power_out | Internal bias supply output that must be decoupled with a 1µF capacitor placed close to the VCC and GND pins. |
| 15 | NC | unconnected | No connection; the pin must be left floating. |
| 16 | SW | output | Switch output that requires a wide PCB trace for the connection. |
| 17 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Monolithic Power Systems |
| Package | QFN-16(3x3) |
| Category | Power Supply Chip |
| Pins | 17 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage range | VIN | 3 | | 17 | V | | 4 |
| Valley current limit | ILIMIT_VY | 8 | | 10 | A | | 4 |
| Feedback current | IFB | 10 | | 50 | nA | VFB = 700mV | 4 |
| Switching frequency | fSW | 600 | 700 | 800 | kHz | | 4 |
| Feedback voltage TJ = 25°C | VFB | 594 | 600 | 606 | mV | TJ = 25°C | 4 |
| Feedback voltage TJ = -40°C to +125°C | VFB | 591 | 600 | 609 | mV | TJ = -40°C to +125°C | 4 |
| Soft-start current | ISS_START | 4 | 6 | 8 | µA | | 4 |
| EN rising threshold | VEN RISING | 1.1 | 1.25 | 1.4 | V | | 4 |
| EN falling threshold | VEN FALLING | 0.9 | 1 | 1.1 | V | | 4 |
| VCC under-voltage lockout rising threshold | VCCVth | 2.6 | 2.8 | 3 | V | | 4 |
| Supply current quiescent | IQ | | 100 | 150 | µA | VEN = 2V, VFB = 0.65V | 4 |
| Supply current shutdown | IIN | | | 5 | µA | VEN = 0V | 4 |
| Switch leakage | SWLKG | | | 1 | µA | VEN = 0V, VSW = 17V | 4 |
| VCC under-voltage lockout threshold | VCCHYS | | 350 | | mV | | 4 |
| VCC load regulation | RegVCC | | 3 | | % | ICC = 5mA | 4 |
| Power good UV rising threshold | PGUVvth_Hi | 0.85 | 0.9 | 0.95 | VFB | | 5 |
| Power good UV falling threshold | PGUVvth_Lo | 0.75 | 0.8 | 0.85 | VFB | | 5 |
| Power good OV rising threshold | PGOVvth_Hi | 1.15 | 1.2 | 1.25 | VFB | | 5 |
| Power good OV falling threshold | PGOVvth_Lo | 1.05 | 1.1 | 1.15 | VFB | | 5 |
| Input voltage absolute maximum | VIN | -0.3 | | 20 | V | | 3 |
| Voltage on all other pins | | -0.3 | | 4 | V | All other pins | 3 |
| Junction temperature | TJ | | | 150 | °C | | 3 |
| Storage temperature | TSTORE | -65 | | 125 | °C | | 3 |
| Supply voltage | VIN | 3 | | 17 | V | | 3 |
| Output voltage | VOUT | 0.6 | | 12 | V | Upper limit is VIN*DMAX or 12V max | 3 |
| Operating junction temperature | TJ | -40 | | 125 | °C | | 3 |
| Thermal resistance junction-to-case | θJC | | 10 | | °C/W | QFN-16, measured on EV8770C-Q-00A 4-layer PCB | 3 |
| Thermal resistance junction-to-ambient (JESD51-7 board) | θJA | | 50 | | °C/W | JESD51-7 board | 3 |
| Thermal resistance junction-to-case (JESD51-7 board) | θJC | | 12 | | °C/W | JESD51-7 board | 3 |
| HS switch on resistance | HSRDS-ON | | 22 | | mΩ | VBST-SW = 3.3V | 4 |
| LS switch on resistance | LSRDS-ON | | 10 | | mΩ | VCC = 3.3V | 4 |
| Short hiccup duty cycle | DHICCUP | | 10 | | % | | 4 |
| Minimum on time | tON_MIN | | 50 | | ns | | 4 |
| Minimum off time | tOFF_MIN | | 100 | | ns | | 4 |
| EN pin pull-down resistor | REN_PD | | 1.2 | | MΩ | | 4 |
| VCC regulator | VCC | | 3.4 | | V | | 4 |
| Power good delay | PGTd | | 50 | | µs | Both edge | 5 |
| Power good sink current capability | VPG Sink | | 0.4 | | V | Sink 4mA | 5 |
| Power good leakage current | IPG_LEAK | | 10 | | µA | VPG = 5V | 5 |
| Thermal shutdown | TSD | | 150 | | °C | | 5 |
| Thermal hysteresis | TSD-HYS | | 20 | | °C | | 5 |
## Materials and finish
As the datasheet states them (page.json `metadata.appearance`; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | | System ground. This pin is the reference ground of the regulated output voltage, so care must be taken during PCB layout. It is recommended to connect it to GND with copper pours | 3 |
## CAD (KiCad official)
- Symbol: `MP8770CGQ-Z`
- Footprint: `Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm`
- 3D model: QFN-16(3x3) (KiCad packages3D, STEP)
- 3D model files: `mp8770cgq-z-etched.step` / `mp8770cgq-z-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `mp8770cgq-z.step` / `mp8770cgq-z.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Monolithic Power Systems datasheet, copy hosted by LCSC](docs/mp8770cgq-z-datasheet.pdf) (23 pp, sha256 `341e02dfba84eade`, retrieved 2026-11-21)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/mp8770cgq-z-datasheet.pdf)