main
Ray
Publish 0.1.0
8caadcf
MP6500AGF-Z
Monolithic Power Systems · Motor Driver ICs · TSSOP-28-EP
MP6500AGF-Z from Monolithic Power Systems, in a TSSOP-28-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VG | power_out | Low-side MOSFET gate drive voltage, which requires a 220nF to 1µF, 16V, ceramic capacitor to ground. |
| 2 | nSLEEP | input | Sleep mode input; drive nSLEEP to logic high to enable normal operation, and it has an internal pull-down resistor. |
| 3 | nENBL | input | Enable input; logic low enables the bridge outputs and translator operation, logic high disables them, and it has an internal pull-down resistor. |
| 4 | GND | power_in | Power ground. |
| 5 | GND | power_in | Power ground. |
| 6 | AOUT2 | output | Bridge A output terminal 2. |
| 7 | VIN | power_in | Input supply voltage; all VIN pins must be connected to the same supply and decoupled to ground with a minimum 100nF ceramic capacitor. |
| 8 | VIN | power_in | Input supply voltage; all VIN pins must be connected to the same supply and decoupled to ground with a minimum 100nF ceramic capacitor. |
| 9 | AOUT1 | output | Bridge A output terminal 1. |
| 10 | GND | power_in | Power ground. |
| 11 | DIR | input | Direction input that sets the direction of rotation of the stepper motor, and it has an internal pull-down resistor. |
| 12 | nFAULT | output | Fault indication open-drain output that is driven low in a fault condition (OCP, OTP, OVP). |
| 13 | VSET | input | Current set programming; a voltage between 0V and 2V applied to VSET sets the current through the motor. |
| 14 | AGND | power_in | Analog ground. |
| 15 | ROSC | passive | Constant off-time programming; a resistor from ROSC to ground sets the PWM off time. |
| 16 | MS2 | input | Mode selection input which, together with MS1, sets the step mode (full-, half-, quarter-, or eighth-step), and it has an internal pull-down resistor. |
| 17 | MS1 | input | Mode selection input which, together with MS2, sets the step mode (full-, half-, quarter-, or eighth-step), and it has an internal pull-down resistor. |
| 18 | GND | power_in | Power ground. |
| 19 | GND | power_in | Power ground. |
| 20 | BOUT1 | output | Bridge B output terminal 1. |
| 21 | VIN | power_in | Input supply voltage; all VIN pins must be connected to the same supply and decoupled to ground with a minimum 100nF ceramic capacitor. |
| 22 | VIN | power_in | Input supply voltage; all VIN pins must be connected to the same supply and decoupled to ground with a minimum 100nF ceramic capacitor. |
| 23 | BOUT2 | output | Bridge B output terminal 2. |
| 24 | GND | power_in | Power ground. |
| 25 | STEP | input | Step input; the rising edge sequences the translator and advances the motor by one increment, and it has an internal pull-down resistor. |
| 26 | VCP | power_out | Charge pump output, which requires a 1µF, 16V, ceramic capacitor to VIN. |
| 27 | CP2 | passive | Charge pump capacitor terminal; connect a 100nF ceramic capacitor rated for the VIN voltage between CP1 and CP2. |
| 28 | CP1 | passive | Charge pump capacitor terminal; connect a 100nF ceramic capacitor rated for the VIN voltage between CP1 and CP2. |
| 29 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Monolithic Power Systems |
| Package | TSSOP-28-EP |
| Category | Power Management ICs |
| Pins | 29 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input supply voltage | VIN | 4.5 | 24 | 35 | V | 5 | |
| Input OVP threshold | VOVP | 36 | 37.5 | 38.5 | V | 5 | |
| Over-current trip level sinking | IOCP1 | 3.5 | 6 | 8.5 | A | Sinking | 5 |
| Over-current trip level sourcing | IOCP2 | 3.5 | 6 | 8.5 | A | Sourcing | 5 |
| Peak current regulation level | IPEAK | 0.95 | 1 | 1.05 | A | VVSET = 0.75V | 5 |
| VSET voltage range | VVSET | 0 | 2 | V | 5 | ||
| Constant off time | tOFF | 20 | 23 | 26 | µs | ROSC = 200kΩ | 5 |
| Current trip accuracy 71% to 100% | ΔITRIP | -5 | 5 | % | VVSET = 0.75V, 71% - 100% | 5 | |
| Current trip accuracy 38% to 67% | ΔITRIP | -9 | 9 | % | VVSET = 0.75V, 38% - 67% | 5 | |
| Current trip accuracy below 34% | ΔITRIP | -12 | 12 | % | VVSET = 0.75V, <34% | 5 | |
| Quiescent current | IQ | 1.9 | 5 | mA | VIN = 24V, nENBL = 0, nSLEEP = 1, with no load | 5 | |
| Sleep current | ISLEEP | 1 | µA | VIN = 24V, nSLEEP = 0 | 5 | ||
| Output on resistance high side 25°C | RHS | 0.195 | 0.23 | Ω | VIN = 24V, IOUT = 1A, TJ = 25°C | 5 | |
| Output on resistance high side 85°C | RHS | 0.25 | Ω | VIN = 24V, IOUT = 1A, TJ = 85°C | 5 | ||
| Output on resistance low side 25°C | RLS | 0.17 | 0.22 | Ω | VIN = 24V, IOUT = 1A, TJ = 25°C | 5 | |
| Output on resistance low side 85°C | RLS | 0.25 | Ω | VIN = 24V, IOUT = 1A, TJ = 85°C | 5 | ||
| Body diode forward voltage | VF | 1.1 | V | IOUT = 1.5A | 5 | ||
| Input logic low threshold | VIL | 0.8 | V | 5 | |||
| Input logic high threshold | VIH | 2.1 | V | 5 | |||
| Logic input current high | IIN(H) | 20 | µA | VIH = 5V | 5 | ||
| Logic input current low | IIN(L) | 5 | µA | VIL = 0.8V | 5 | ||
| nFAULT output low voltage | VOL | 0.5 | V | IO = 5mA | 5 | ||
| Output high leakage current | IOH | 1 | µA | VO = 3.3V | 5 | ||
| UVLO rising threshold | VIN_RISE | 3.4 | 4.5 | V | 5 | ||
| Over-current deglitch time | tOCP | 1 | µs | 5 | |||
| STEP high time | t1 | 1 | µs | 6 | |||
| STEP low time | t2 | 1 | µs | 6 | |||
| Set-up time MSx, DIR to STEP rising | t3 | 200 | ns | 6 | |||
| Hold time STEP rising to MSx, DIR change | t4 | 200 | ns | 6 | |||
| Supply voltage | VIN | 4.5 | 35 | V | 4 | ||
| Output current | IA/BOUT | -2.5 | 2.5 | A | 4 | ||
| Operating junction temperature | TJ | -40 | 125 | °C | 4 | ||
| Supply voltage absolute maximum | VIN | -0.3 | 40 | V | 4 | ||
| xOUTx voltage | VA/BOUT1/2 | -0.7 | 40 | V | 4 | ||
| xOUTx voltage transient | VA/BOUT1/2 | -1.5 | V | transient, 2µs; upper limit VIN + 1.5V | 4 | ||
| CP1 voltage transient | CP1 | -1.5 | V | transient, 2µs; upper limit VIN + 1.5V | 4 | ||
| All other pins to AGND | -0.3 | 6.5 | V | 4 | |||
| Storage temperature | TSTORE | -55 | 150 | °C | 4 | ||
| Junction temperature | TJ | 150 | °C | 4 | |||
| Lead temperature (solder) | 260 | °C | 4 | ||||
| Thermal resistance junction-to-ambient TSSOP-28EP | θJA | 32 | °C/W | JESD51-7, 4-layer PCB | 4 | ||
| Thermal resistance junction-to-case TSSOP-28EP | θJC | 6 | °C/W | JESD51-7, 4-layer PCB | 4 | ||
| Overvoltage hysteresis | ΔVOVP | 1900 | mV | 5 | |||
| Internal pull-down resistance | RPD | 500 | kΩ | 5 | |||
| Thermal shutdown | TTSD | 165 | °C | 5 | |||
| Thermal shutdown hysteresis | ΔTTSD | 15 | °C | 5 | |||
| VSET voltage ratio | AVSET | 0.75 | V/A | 5 | |||
| Blanking time | tBLANK | 2 | µs | 5 |
CAD (KiCad official)
- Symbol:
MP6500AGF-Z - Footprint:
Package_SO:TSSOP-28-1EP_4.4x9.7mm_P0.65mm_EP2.85x6.7mm - 3D model: TSSOP-28-EP (KiCad packages3D, STEP)
- 3D model files:
mp6500agf-z-etched.step/mp6500agf-z-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mp6500agf-z.step/mp6500agf-z.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Monolithic Power Systems datasheet, copy hosted by LCSC (20 pp, sha256
0691288e75c73d5d, retrieved 2026-11-21) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# MP6500AGF-Z
**Monolithic Power Systems** · Motor Driver ICs · TSSOP-28-EP
MP6500AGF-Z from Monolithic Power Systems, in a TSSOP-28-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VG | power_out | Low-side MOSFET gate drive voltage, which requires a 220nF to 1µF, 16V, ceramic capacitor to ground. |
| 2 | nSLEEP | input | Sleep mode input; drive nSLEEP to logic high to enable normal operation, and it has an internal pull-down resistor. |
| 3 | nENBL | input | Enable input; logic low enables the bridge outputs and translator operation, logic high disables them, and it has an internal pull-down resistor. |
| 4 | GND | power_in | Power ground. |
| 5 | GND | power_in | Power ground. |
| 6 | AOUT2 | output | Bridge A output terminal 2. |
| 7 | VIN | power_in | Input supply voltage; all VIN pins must be connected to the same supply and decoupled to ground with a minimum 100nF ceramic capacitor. |
| 8 | VIN | power_in | Input supply voltage; all VIN pins must be connected to the same supply and decoupled to ground with a minimum 100nF ceramic capacitor. |
| 9 | AOUT1 | output | Bridge A output terminal 1. |
| 10 | GND | power_in | Power ground. |
| 11 | DIR | input | Direction input that sets the direction of rotation of the stepper motor, and it has an internal pull-down resistor. |
| 12 | nFAULT | output | Fault indication open-drain output that is driven low in a fault condition (OCP, OTP, OVP). |
| 13 | VSET | input | Current set programming; a voltage between 0V and 2V applied to VSET sets the current through the motor. |
| 14 | AGND | power_in | Analog ground. |
| 15 | ROSC | passive | Constant off-time programming; a resistor from ROSC to ground sets the PWM off time. |
| 16 | MS2 | input | Mode selection input which, together with MS1, sets the step mode (full-, half-, quarter-, or eighth-step), and it has an internal pull-down resistor. |
| 17 | MS1 | input | Mode selection input which, together with MS2, sets the step mode (full-, half-, quarter-, or eighth-step), and it has an internal pull-down resistor. |
| 18 | GND | power_in | Power ground. |
| 19 | GND | power_in | Power ground. |
| 20 | BOUT1 | output | Bridge B output terminal 1. |
| 21 | VIN | power_in | Input supply voltage; all VIN pins must be connected to the same supply and decoupled to ground with a minimum 100nF ceramic capacitor. |
| 22 | VIN | power_in | Input supply voltage; all VIN pins must be connected to the same supply and decoupled to ground with a minimum 100nF ceramic capacitor. |
| 23 | BOUT2 | output | Bridge B output terminal 2. |
| 24 | GND | power_in | Power ground. |
| 25 | STEP | input | Step input; the rising edge sequences the translator and advances the motor by one increment, and it has an internal pull-down resistor. |
| 26 | VCP | power_out | Charge pump output, which requires a 1µF, 16V, ceramic capacitor to VIN. |
| 27 | CP2 | passive | Charge pump capacitor terminal; connect a 100nF ceramic capacitor rated for the VIN voltage between CP1 and CP2. |
| 28 | CP1 | passive | Charge pump capacitor terminal; connect a 100nF ceramic capacitor rated for the VIN voltage between CP1 and CP2. |
| 29 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Monolithic Power Systems |
| Package | TSSOP-28-EP |
| Category | Power Management ICs |
| Pins | 29 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input supply voltage | VIN | 4.5 | 24 | 35 | V | | 5 |
| Input OVP threshold | VOVP | 36 | 37.5 | 38.5 | V | | 5 |
| Over-current trip level sinking | IOCP1 | 3.5 | 6 | 8.5 | A | Sinking | 5 |
| Over-current trip level sourcing | IOCP2 | 3.5 | 6 | 8.5 | A | Sourcing | 5 |
| Peak current regulation level | IPEAK | 0.95 | 1 | 1.05 | A | VVSET = 0.75V | 5 |
| VSET voltage range | VVSET | 0 | | 2 | V | | 5 |
| Constant off time | tOFF | 20 | 23 | 26 | µs | ROSC = 200kΩ | 5 |
| Current trip accuracy 71% to 100% | ΔITRIP | -5 | | 5 | % | VVSET = 0.75V, 71% - 100% | 5 |
| Current trip accuracy 38% to 67% | ΔITRIP | -9 | | 9 | % | VVSET = 0.75V, 38% - 67% | 5 |
| Current trip accuracy below 34% | ΔITRIP | -12 | | 12 | % | VVSET = 0.75V, <34% | 5 |
| Quiescent current | IQ | | 1.9 | 5 | mA | VIN = 24V, nENBL = 0, nSLEEP = 1, with no load | 5 |
| Sleep current | ISLEEP | | | 1 | µA | VIN = 24V, nSLEEP = 0 | 5 |
| Output on resistance high side 25°C | RHS | | 0.195 | 0.23 | Ω | VIN = 24V, IOUT = 1A, TJ = 25°C | 5 |
| Output on resistance high side 85°C | RHS | | | 0.25 | Ω | VIN = 24V, IOUT = 1A, TJ = 85°C | 5 |
| Output on resistance low side 25°C | RLS | | 0.17 | 0.22 | Ω | VIN = 24V, IOUT = 1A, TJ = 25°C | 5 |
| Output on resistance low side 85°C | RLS | | | 0.25 | Ω | VIN = 24V, IOUT = 1A, TJ = 85°C | 5 |
| Body diode forward voltage | VF | | | 1.1 | V | IOUT = 1.5A | 5 |
| Input logic low threshold | VIL | | | 0.8 | V | | 5 |
| Input logic high threshold | VIH | 2.1 | | | V | | 5 |
| Logic input current high | IIN(H) | | | 20 | µA | VIH = 5V | 5 |
| Logic input current low | IIN(L) | | | 5 | µA | VIL = 0.8V | 5 |
| nFAULT output low voltage | VOL | | | 0.5 | V | IO = 5mA | 5 |
| Output high leakage current | IOH | | | 1 | µA | VO = 3.3V | 5 |
| UVLO rising threshold | VIN_RISE | 3.4 | | 4.5 | V | | 5 |
| Over-current deglitch time | tOCP | | 1 | | µs | | 5 |
| STEP high time | t1 | 1 | | | µs | | 6 |
| STEP low time | t2 | 1 | | | µs | | 6 |
| Set-up time MSx, DIR to STEP rising | t3 | 200 | | | ns | | 6 |
| Hold time STEP rising to MSx, DIR change | t4 | 200 | | | ns | | 6 |
| Supply voltage | VIN | 4.5 | | 35 | V | | 4 |
| Output current | IA/BOUT | -2.5 | | 2.5 | A | | 4 |
| Operating junction temperature | TJ | -40 | | 125 | °C | | 4 |
| Supply voltage absolute maximum | VIN | -0.3 | | 40 | V | | 4 |
| xOUTx voltage | VA/BOUT1/2 | -0.7 | | 40 | V | | 4 |
| xOUTx voltage transient | VA/BOUT1/2 | -1.5 | | | V | transient, 2µs; upper limit VIN + 1.5V | 4 |
| CP1 voltage transient | CP1 | -1.5 | | | V | transient, 2µs; upper limit VIN + 1.5V | 4 |
| All other pins to AGND | | -0.3 | | 6.5 | V | | 4 |
| Storage temperature | TSTORE | -55 | | 150 | °C | | 4 |
| Junction temperature | TJ | | | 150 | °C | | 4 |
| Lead temperature (solder) | | | | 260 | °C | | 4 |
| Thermal resistance junction-to-ambient TSSOP-28EP | θJA | | 32 | | °C/W | JESD51-7, 4-layer PCB | 4 |
| Thermal resistance junction-to-case TSSOP-28EP | θJC | | 6 | | °C/W | JESD51-7, 4-layer PCB | 4 |
| Overvoltage hysteresis | ΔVOVP | | 1900 | | mV | | 5 |
| Internal pull-down resistance | RPD | | 500 | | kΩ | | 5 |
| Thermal shutdown | TTSD | | 165 | | °C | | 5 |
| Thermal shutdown hysteresis | ΔTTSD | | 15 | | °C | | 5 |
| VSET voltage ratio | AVSET | | 0.75 | | V/A | | 5 |
| Blanking time | tBLANK | | 2 | | µs | | 5 |
## CAD (KiCad official)
- Symbol: `MP6500AGF-Z`
- Footprint: `Package_SO:TSSOP-28-1EP_4.4x9.7mm_P0.65mm_EP2.85x6.7mm`
- 3D model: TSSOP-28-EP (KiCad packages3D, STEP)
- 3D model files: `mp6500agf-z-etched.step` / `mp6500agf-z-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `mp6500agf-z.step` / `mp6500agf-z.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Monolithic Power Systems datasheet, copy hosted by LCSC](docs/mp6500agf-z-datasheet.pdf) (20 pp, sha256 `0691288e75c73d5d`, retrieved 2026-11-21)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/mp6500agf-z-datasheet.pdf)