component
MP5610GQG-Z
Public Made by Adomby adom
Monolithic Power Systems Others, QFN-10(1.4x1.8). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
main
MP5610GQG-Z
Monolithic Power Systems · Others · QFN-10(1.4x1.8)
MP5610GQG-Z from Monolithic Power Systems, in a QFN-10(1.4x1.8). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | EN | input | Enable pin: a voltage above the 1.2V EN high threshold enables the IC, while pulling it below 0.4V or leaving it floating disables the IC. |
| 2 | FBP | input | Positive output step-up converter feedback pin, regulated to a 600mV feedback voltage (±1%) set by an external resistor divider. |
| 3 | VON | power_out | Charge pump negative output pin; the IC latches off if VON falls below 60% of VOP, and negative overvoltage protection trips at -6.2V typical. |
| 4 | CP2 | passive | Negative output charge pump flying capacitor node 2, connected to CP1 through the flying capacitor (0.1µF to 1µF typical). |
| 5 | CP1 | passive | Negative output charge pump flying capacitor node 1; connect a flying capacitor between this pin and CP2. |
| 6 | GND | power_in | Ground reference pin. |
| 7 | VOP | power_out | Step-up converter positive output pin; positive overvoltage protection threshold is 6.1V typical and under-voltage protection is at 52% of VREF. |
| 8 | SW | passive | Step-up converter power switch node, the drain of the internal low-side MOSFET; connect the power inductor between SW and VINP. |
| 9 | VINP | power_in | Input power pin for the step-up power stage, internally connected to the source node of the internal N-MOSFET. |
| 10 | VIN | power_in | Input power pin that supplies internal logic and driver with 2.7V to 5.5V input voltage and must be locally bypassed. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Monolithic Power Systems |
| Package | QFN-10(1.4x1.8) |
| Category | Others |
| Pins | 10 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Operating Input Voltage | VIN | 2.7 | 5.5 | V | 3 | ||
| Input UVLO Threshold | VIN_UVLO | 2.35 | 2.45 | 2.55 | V | Rising Edge | 3 |
| Switching Frequency | fSW | 0.96 | 1.2 | 1.44 | MHz | 3 | |
| Input DC Current Limit | ILIM_IN | 200 | 245 | 290 | mA | VIN=3.7V | 3 |
| Maximum Duty Cycle | DMAX | 75 | 85 | % | 3 | ||
| Feedback Regulation Voltage | VFBP | 594 | 600 | 606 | mV | 3 | |
| Cycle-by-Cycle Current Limit | ILIM | 240 | 300 | 365 | mA | Duty Cycle=0% | 3 |
| High Side Switch Current ZCD Detection Threshold | 5 | 10 | 15 | mA | 3 | ||
| Positive Output Over Voltage Protection Threshold | VOVP | 5.9 | 6.1 | 6.4 | V | 3 | |
| Negative Output Over Voltage Protection Threshold | VOVN | -6.7 | -6.2 | -5.8 | V | 3 | |
| Supply Current (Quiescent) | IQ | 450 | 500 | μA | VIN=3.7V, VEN= VIN, no switching | 3 | |
| Input Voltage Absolute Maximum | VIN, VINP | -0.3 | 6.5 | V | 2 | ||
| Switch and Output Voltage Absolute Maximum | VSW, VOP, VCP1 | -0.3 | 7 | V | 2 | ||
| Negative Charge Pump Voltage Absolute Maximum | VCP2, VON | -7 | 0.3 | V | 2 | ||
| All Other Pins Absolute Maximum | -0.3 | 6.5 | V | 2 | |||
| Lead Temperature Absolute Maximum | 260 | °C | 2 | ||||
| Continuous Power Dissipation | PD | 0.892 | W | TA = 25°C, QFN-10 (1.4mm×1.8mm) | 2 | ||
| Supply Voltage VIN | VIN | 2.7 | 5.5 | V | 2 | ||
| Operating Junction Temperature | TJ | -40 | 125 | °C | 2 | ||
| Thermal Resistance Junction-to-Ambient | θJA | 140 | °C/W | QFN-10 (1.4mm×1.8mm), measured on JESD51-7, 4-layer PCB | 2 | ||
| Thermal Resistance Junction-to-Case | θJC | 30 | °C/W | QFN-10 (1.4mm×1.8mm) | 2 |
CAD (KiCad official)
- Symbol:
MP5610GQG-Z - Footprint:
Package_DFN_QFN:UQFN-10_1.4x1.8mm_P0.4mm - 3D model: QFN-10(1.4x1.8) (KiCad packages3D, STEP)
- 3D model files:
mp5610gqg-z-etched.step/mp5610gqg-z-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mp5610gqg-z.step/mp5610gqg-z.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Monolithic Power Systems datasheet (16 pp, sha256
323d32e0bb92a25e, retrieved 2026-10-28, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# MP5610GQG-Z
**Monolithic Power Systems** · Others · QFN-10(1.4x1.8)
MP5610GQG-Z from Monolithic Power Systems, in a QFN-10(1.4x1.8). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | EN | input | Enable pin: a voltage above the 1.2V EN high threshold enables the IC, while pulling it below 0.4V or leaving it floating disables the IC. |
| 2 | FBP | input | Positive output step-up converter feedback pin, regulated to a 600mV feedback voltage (±1%) set by an external resistor divider. |
| 3 | VON | power_out | Charge pump negative output pin; the IC latches off if VON falls below 60% of VOP, and negative overvoltage protection trips at -6.2V typical. |
| 4 | CP2 | passive | Negative output charge pump flying capacitor node 2, connected to CP1 through the flying capacitor (0.1µF to 1µF typical). |
| 5 | CP1 | passive | Negative output charge pump flying capacitor node 1; connect a flying capacitor between this pin and CP2. |
| 6 | GND | power_in | Ground reference pin. |
| 7 | VOP | power_out | Step-up converter positive output pin; positive overvoltage protection threshold is 6.1V typical and under-voltage protection is at 52% of VREF. |
| 8 | SW | passive | Step-up converter power switch node, the drain of the internal low-side MOSFET; connect the power inductor between SW and VINP. |
| 9 | VINP | power_in | Input power pin for the step-up power stage, internally connected to the source node of the internal N-MOSFET. |
| 10 | VIN | power_in | Input power pin that supplies internal logic and driver with 2.7V to 5.5V input voltage and must be locally bypassed. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Monolithic Power Systems |
| Package | QFN-10(1.4x1.8) |
| Category | Others |
| Pins | 10 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Operating Input Voltage | VIN | 2.7 | | 5.5 | V | | 3 |
| Input UVLO Threshold | VIN_UVLO | 2.35 | 2.45 | 2.55 | V | Rising Edge | 3 |
| Switching Frequency | fSW | 0.96 | 1.2 | 1.44 | MHz | | 3 |
| Input DC Current Limit | ILIM_IN | 200 | 245 | 290 | mA | VIN=3.7V | 3 |
| Maximum Duty Cycle | DMAX | 75 | 85 | | % | | 3 |
| Feedback Regulation Voltage | VFBP | 594 | 600 | 606 | mV | | 3 |
| Cycle-by-Cycle Current Limit | ILIM | 240 | 300 | 365 | mA | Duty Cycle=0% | 3 |
| High Side Switch Current ZCD Detection Threshold | | 5 | 10 | 15 | mA | | 3 |
| Positive Output Over Voltage Protection Threshold | VOVP | 5.9 | 6.1 | 6.4 | V | | 3 |
| Negative Output Over Voltage Protection Threshold | VOVN | -6.7 | -6.2 | -5.8 | V | | 3 |
| Supply Current (Quiescent) | IQ | | 450 | 500 | μA | VIN=3.7V, VEN= VIN, no switching | 3 |
| Input Voltage Absolute Maximum | VIN, VINP | -0.3 | | 6.5 | V | | 2 |
| Switch and Output Voltage Absolute Maximum | VSW, VOP, VCP1 | -0.3 | | 7 | V | | 2 |
| Negative Charge Pump Voltage Absolute Maximum | VCP2, VON | -7 | | 0.3 | V | | 2 |
| All Other Pins Absolute Maximum | | -0.3 | | 6.5 | V | | 2 |
| Lead Temperature Absolute Maximum | | | | 260 | °C | | 2 |
| Continuous Power Dissipation | PD | | | 0.892 | W | TA = 25°C, QFN-10 (1.4mm×1.8mm) | 2 |
| Supply Voltage VIN | VIN | 2.7 | | 5.5 | V | | 2 |
| Operating Junction Temperature | TJ | -40 | | 125 | °C | | 2 |
| Thermal Resistance Junction-to-Ambient | θJA | | 140 | | °C/W | QFN-10 (1.4mm×1.8mm), measured on JESD51-7, 4-layer PCB | 2 |
| Thermal Resistance Junction-to-Case | θJC | | 30 | | °C/W | QFN-10 (1.4mm×1.8mm) | 2 |
## CAD (KiCad official)
- Symbol: `MP5610GQG-Z`
- Footprint: `Package_DFN_QFN:UQFN-10_1.4x1.8mm_P0.4mm`
- 3D model: QFN-10(1.4x1.8) (KiCad packages3D, STEP)
- 3D model files: `mp5610gqg-z-etched.step` / `mp5610gqg-z-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `mp5610gqg-z.step` / `mp5610gqg-z.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Monolithic Power Systems datasheet](docs/mp5610gqg-z-datasheet.pdf) (16 pp, sha256 `323d32e0bb92a25e`, retrieved 2026-10-28, tier: lcsc)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/mp5610gqg-z-datasheet.pdf)