Generated by kicad-footprint-generator · KiCad file format 20260206
MP4653GY-Z
Monolithic Power Systems · LED Drivers · SOIC-20-300mil
MP4653GY-Z from Monolithic Power Systems, in a SOIC-20-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SS | passive | Soft-start node that, together with FSET, sets the operating frequency through RSS_FSET and sets the start-up frequency and soft-start time through Rss and Css; its normal voltage is 1.49V and it is pulled low to 0V on a bus-stage fault. |
| 2 | FSET | passive | Frequency-set pin with a resistor to GND whose sourcing current, combined with the SS pin current, determines the operating frequency. |
| 3 | VOCP | input | Bus-stage over-current sense input (negative polarity), where bus-stage protection triggers when VOCP falls below -100mV. |
| 4 | VFB | input | Bus voltage feedback input sampled at PWM-on and used as the bus control-loop reference, with bus over-voltage protection triggered when it exceeds 2.4V. |
| 5 | VCOMP | passive | Voltage control-loop compensation node that takes a capacitor or RC network to GND (typically 47nF to 470nF and 2kΩ to 200kΩ), also used as the bus-stage hiccup timer charging to 3V and discharging to 0.45V. |
| 6 | ICOMP | passive | Current control-loop compensation node that takes a capacitor or RC network to GND (typically 47nF to 470nF and 200Ω to 5kΩ), also used as the LED-stage hiccup timer charging to 3V and discharging to 0.45V. |
| 7 | IFB | input | LED current feedback input from the sense resistor, regulated to 0.2V when A-Dim is high, with LED over-current protection triggered when it exceeds 0.3V for 200μs or 0.6V. |
| 8 | SSD | input | LED-stage short-string/over-current sense input (negative polarity), where LED-stage protection triggers when the voltage falls below -200mV. |
| 9 | VLED4 | input | Voltage feedback of LED string 4, monitored with VLED1 to VLED3 for maximum voltage and inter-pin voltage difference LED-stage protection. |
| 10 | VLED3 | input | Voltage feedback of LED string 3, monitored with VLED1, VLED2 and VLED4 for maximum voltage and inter-pin voltage difference LED-stage protection. |
| 11 | VLED2 | input | Voltage feedback of LED string 2, monitored with VLED1, VLED3 and VLED4 for maximum voltage and inter-pin voltage difference LED-stage protection. |
| 12 | VLED1 | input | Voltage feedback of LED string 1; if fewer than four LED strings are used, the unused VLED pins must be connected together with the others. |
| 13 | A-Dim | input | Analog dimming input where 0 to 1.18V sets the LED current from 0 to 100%, and it should be pulled high to VCC through 100kΩ if not used. |
| 14 | PWMIN | input | PWM dimming control input for a PWM signal in the range of 100Hz to 2kHz. |
| 15 | VIN | power_in | Supply input for the IC with recommended operating supply voltage of -0.3V to +30V (absolute maximum +38V), to be bypassed with a ceramic capacitor of 0.1μF or larger. |
| 16 | PWMOUT | output | Output driving the external dimming MOSFET for PWM dimming, with a series resistor used to adjust driving speed, and also used to drive the external P-MOS for protection with logic high of 9.4V typical in normal operation. |
| 17 | VCC | power_out | Gate driver and internal circuit supply (about 9V typical) that can also supply external circuits, to be bypassed with a ceramic capacitor of 1μF or larger. |
| 18 | GL | output | Gate drive output for the power stage, 180 degrees phase shifted from GR, able to drive the external MOSFET directly through a gate driving transformer. |
| 19 | GND | power_in | Ground reference for the control circuit. |
| 20 | GR | output | Gate drive output for the power stage, 180 degrees phase shifted from GL, able to drive the external MOSFET directly through a gate driving transformer. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Monolithic Power Systems |
| Package | SOIC-20-300mil |
| Category | LED Drivers |
| Pins | 20 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage Vin | Vin | -0.3 | 38 | V | 3 | ||
| GL, GR, VCC, PWMOUT voltage | -0.5 | 10.7 | V | 3 | |||
| SSD, VOCP voltage | -6.5 | 4 | V | 3 | |||
| Other pins voltage | -0.5 | 7 | V | 3 | |||
| Junction Temperature | 150 | °C | 3 | ||||
| Continuous Power Dissipation | 1.7 | W | TA = +25°C | 3 | |||
| Storage Temperature | -65 | 150 | °C | 3 | |||
| Operating frequency | 300 | kHz | 3 | ||||
| Supply Voltage Vin | Vin | -0.3 | 30 | V | 3 | ||
| Operating frequency | 20 | 250 | kHz | 3 | |||
| Operating Junction Temp | -40 | 125 | °C | 3 | |||
| Dead time | tdead | 600 | 750 | 900 | ns | 4 | |
| Gate Driver Supply Voltage (VCC) | VVCC | 9 | 9.4 | 9.8 | V | IVCC=0mA | 4 |
| Gate Driver Supply Voltage (VCC) | VVCC | 8.8 | 9.3 | V | IVCC=30mA | 4 | |
| Gate Driver Supply Current | IVCC | 20 | 50 | mA | 4 | ||
| Vin UVLO threshold | VTH_UVLO_VIN | 4.2 | 4.35 | 4.5 | V | VCC rising | 4 |
| Analog Dimming Full Scale | VA-dim | 1.13 | 1.18 | 1.23 | V | Analog dimming | 4 |
| PWM Logic Input Threshold | VTH-PWM | 1.6 | 1.9 | 2.2 | V | PWM dimming | 4 |
| Supply Current | IIN | 1.6 | 2.5 | mA | No driver output | 4 | |
| Minimum Frequency Set Voltage | VFSET | 0.95 | 1 | 1.05 | V | 4 | |
| SS pin voltage | Vss | 1.45 | 1.49 | 1.53 | V | At normal operation | 4 |
| Minimum operating frequency | Fmin_op | 35.6 | 38.6 | 41.6 | kHz | RFSET=RSS_FSET=40kΩ, IFB=0.1V(ICOMP=2.2V), PWMIN=high | 4 |
| Maximum Operating Frequency | Fmax_op | 2.2 | 2.5 | 2.8 | Fmin | RFSET=RSS_FSET=40kΩ, IFB=0.21V(ICOMP=1V), PWMIN=high | 4 |
| Logic High Voltage | VH-PWMOUT | 9 | 9.4 | 9.8 | V | Normal Operation | 4 |
| LED Current Feedback magnitude | /VIFB/ | 0.192 | 0.2 | 0.208 | V | 4 | |
| LED Short Threshold for Immediate action | VIFBS | 540 | 600 | 660 | mV | 4 | |
| LED short detection blanking time | Tblank | 100 | 140 | 180 | ns | 4 | |
| LED short threshold for slow action | VIFBSC | 270 | 300 | 330 | mV | 5 | |
| Delay time for slow action | Tdelay_IFB | 100 | 200 | 350 | µs | 300mV<VIFB<600mV | 5 |
| Input common-mode range | VCM_I | -0.3 | 4 | V | 5 | ||
| Saturated output current | Isat_I | 35 | 50 | 65 | μA | 5 | |
| Low level clamp voltage | VICOMP_L | 0.95 | 1 | 1.05 | V | Normal operation | 5 |
| High level clamp voltage | VICOMP_H | 2.15 | 2.2 | 2.25 | V | Normal operation | 5 |
| Minimum clamp voltage | Vmin_clamp_VFB | 1.1 | 1.2 | 1.3 | V | 5 | |
| Maximum clamp voltage | Vmax_clamp_VFB | 1.9 | 2 | 2.1 | V | 5 | |
| Over LED Voltage Protection Threshold | VTH(OVP_LED) | 2.25 | 2.4 | 2.55 | V | 5 | |
| Over LED voltage delay time | Tdelay_VLED | 1.7 | 2.3 | 2.9 | μs | 5 | |
| Gain of differential voltage | 14.7 | 16.3 | 17.9 | 5 | |||
| Internal resistance | RVLED | 19 | 23 | 27 | kΩ | 5 | |
| ICOMP Valley Threshold | Vth_low(ICOMP) | 0.35 | 0.45 | 0.55 | V | 5 | |
| ICOMP Peak Threshold | Vth_peak(ICOMP) | 2.7 | 3 | 3.3 | V | 5 | |
| ICOMP charging current at hiccup mode | Icharge_fault(ICOMP) | 1.6 | 2 | 2.4 | µA | 5 | |
| ICOMP discharging current at hiccup mode | Idischarge_fault(ICOMP) | 1.6 | 2 | 2.4 | µA | 5 | |
| VCOMP Valley Threshold | Vth_low(VCOMP) | 0.35 | 0.45 | 0.55 | V | 5 | |
| VCOMP Peak Threshold | Vth_peak(VCOMP) | 2.7 | 3 | 3.3 | V | 6 | |
| VCOMP threshold for burst mode | VTH_burst_VCOMP | 1.05 | 1.1 | 1.15 | V | VFB>1.1VSH | 6 |
| VCOMP hysteresis for burst mode | 70 | 90 | 110 | mV | 6 | ||
| ICOMP threshold for burst mode | VTH_burst_ICOMP | 1.05 | 1.1 | 1.15 | V | VIFB>1.1VIFB_REF | 6 |
| ICOMP hysteresis for burst mode | 70 | 90 | 110 | mV | 6 | ||
| Over bus Voltage Protection Threshold | VTH(OVP_VFB) | 2.25 | 2.4 | 2.55 | V | 6 | |
| Delay Time | 1.7 | 2.3 | 2.9 | µs | VFB>2.4V | 6 | |
| SSD Threshold | VTH_SSD | -225 | -200 | -175 | mV | 6 | |
| SSD Detection Delay Time | TD_SSD | 1.8 | 2.4 | 3 | µs | SSD<-200mV | 6 |
| OCP detection threshold | VTH_OCP | -120 | -100 | -80 | mV | 6 | |
| OCP delay time | TD_OCP | 1.8 | 2.4 | 3 | µs | OCP<-100mV | 6 |
| Thermal resistance junction-to-ambient (SOIC20) | θJA | 72 | °C/W | Measured on JESD51-7, 4-layer PCB | 3 | ||
| Thermal resistance junction-to-case (SOIC20) | θJC | 30 | °C/W | Measured on JESD51-7, 4-layer PCB | 3 |
CAD (KiCad official)
- Symbol:
MP4653GY-Z - Footprint:
Package_SO:SOIC-20W_7.5x12.8mm_P1.27mm - 3D model: SOIC-20-300mil (KiCad packages3D, STEP)
- 3D model files:
mp4653gy-z-etched.step/mp4653gy-z-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mp4653gy-z.step/mp4653gy-z.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Monolithic Power Systems datasheet (25 pp, sha256
d207ba1022551621, retrieved 2026-10-31, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).