3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownMP4581GN-Z
Monolithic Power Systems · DC-DC Converters · SOIC-8-EP
MP4581GN-Z from Monolithic Power Systems, in a SOIC-8-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | EN | input | Power enable: pulling EN high turns the MP4581 on and pulling it low turns it off, and EN cannot be left floating. |
| 2 | VCC | power_out | Internal LDO output that supplies the internal control circuit and must be decoupled with a ≥1μF ceramic capacitor. |
| 3 | FREQ | input | Switching frequency (fSW) setting pin, where an external resistor is connected from FREQ to GND to set the buck fSW. |
| 4 | FB | input | Output voltage (VOUT) feedback input, where a resistor divider from VOUT is connected to the FB pin. |
| 5 | BST | passive | Bootstrap power for the high-side MOSFET gate driver, requiring a 0.1μF capacitor connected between BST and SW. |
| 6 | SW | output | Switch node of the converter, connected to the source of the HS-FET and the drain of the LS-FET. |
| 7 | GND | power_in | Power ground. |
| 8 | VIN | power_in | Power supply input, rated for 8V to 100V per the recommended operating conditions. |
| 9 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Monolithic Power Systems |
| Package | SOIC-8-EP |
| Category | Power Management |
| Pins | 9 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | VIN | 8 | 100 | V | 3 | ||
| Output voltage | VOUT | 1 | 30 | V | 3 | ||
| Operating junction temperature | TJ | -40 | 125 | °C | 3 | ||
| VIN, EN voltage | VIN, EN | -0.3 | 105 | V | 3 | ||
| SW voltage | SW | -0.5 | 105 | V | 3 | ||
| SW voltage (<20ns) | SW | -5 | 111 | V | <20ns | 3 | |
| BST to SW voltage | BST-SW | -0.3 | 6 | V | 3 | ||
| All other pins voltage | -0.3 | 6 | V | 3 | |||
| Continuous power dissipation | 3.2 | W | TA = 25°C | 3 | |||
| Junction temperature | 150 | °C | 3 | ||||
| Lead temperature | 260 | °C | 3 | ||||
| Storage temperature | -65 | 150 | °C | 3 | |||
| VCC UVLO threshold rising | VCCUVLO-R | 3.15 | 3.35 | 3.55 | V | VCC rising | 4 |
| VCC regulation voltage | 4.5 | 4.85 | 5.2 | V | IVCC = 2mA | 4 | |
| VCC UVLO threshold hysteresis | VCCHYS | 150 | mV | 4 | |||
| Shutdown current | ISD | 2 | μA | VEN = 0V, measured on VIN | 4 | ||
| Quiescent current | IQ | 15 | μA | VIN = 12V, VFB = 1.05V, no switching, measured on VIN, TJ = 25°C | 4 | ||
| Micro-power EN start-up threshold | 0.9 | V | 4 | ||||
| Micro-power EN off threshold | 0.4 | V | 4 | ||||
| EN input high threshold | VEN_ON | 1.15 | 1.25 | 1.35 | V | VEN rising | 4 |
| EN hysteresis | VEN_H | 120 | mV | VEN rising/falling | 4 | ||
| Minimum off time | tMIN_OFF | 150 | ns | VFB = 0V | 4 | ||
| Minimum on time | tMIN_ON | 45 | ns | 4 | |||
| FB reference voltage | VREF | 0.99 | 1 | 1.01 | V | 8V to 100V, TJ = 25°C | 4 |
| FB reference voltage over temperature | VREF | 0.985 | 1 | 1.015 | V | 8V to 100V, TJ = -40°C to +125°C | 4 |
| FB input current | IFB | 50 | nA | VFB = 1.05V | 4 | ||
| Soft-start time | tSS | 4.35 | ms | 10% to 90% of VREF | 4 | ||
| FB under-voltage threshold | VUVP | 60 | % VREF | 4 | |||
| LS-FET on resistance | RON_L | 265 | mΩ | 4 | |||
| Synchronous HS-FET on resistance | RON_H | 625 | mΩ | 4 | |||
| LS-FET valley current limit | IVL_LIMT | 0.72 | 0.8 | 0.88 | A | Over full duty cycle, TJ = 25°C | 4 |
| LS-FET valley current limit over temperature | IVL_LIMT | 0.68 | 0.8 | 0.92 | A | Over full duty cycle, TJ = -40°C to +125°C | 4 |
| Inductor current zero-current detection threshold | -60 | 0 | 60 | mA | 4 | ||
| Thermal shutdown | TSD | 150 | °C | 4 | |||
| Thermal shutdown hysteresis | TSD_HYS | 25 | °C | 4 | |||
| Thermal resistance junction-to-ambient | θJA | 38 | °C/W | EV4581-N-00A (4) | 3 | ||
| Thermal resistance junction-to-case | θJC | 7.5 | °C/W | EV4581-N-00A (4) | 3 | ||
| Thermal resistance junction-to-ambient (JESD51-7) | θJA | 48 | °C/W | JESD51-7 (5) | 3 | ||
| Thermal resistance junction-to-case (JESD51-7) | θJC | 10 | °C/W | JESD51-7 (5) | 3 |
CAD (KiCad official)
- Symbol:
MP4581GN-Z - Footprint:
Package_SO:SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.29x3mm - 3D model: SOIC-8-EP (KiCad packages3D, STEP)
- 3D model files:
mp4581gn-z-etched.step/mp4581gn-z-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mp4581gn-z.step/mp4581gn-z.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Monolithic Power Systems datasheet (19 pp, sha256
80bb0160cf520f7e, retrieved 2026-10-27, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).