main
History Download
Ray Publish 0.1.0 339693a

MP4558DN-LF-Z

Monolithic Power Systems · DC-DC Converters · SOIC-8-EP

MP4558DN-LF-Z from Monolithic Power Systems, in a SOIC-8-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 SW output Switch node is the output of the high-side switch and requires a low VF Schottky rectifier to ground, placed close to the SW pins to reduce switching spikes.
2 EN input Enable input: pulling it below the specified threshold shuts the chip down, while pulling it above the threshold or leaving it floating enables the chip.
3 COMP passive Compensation pin for the GM error amplifier output, clamped to 0.9V minimum and 2.0V maximum in operation, with the datasheet advising to avoid pulling it above 2.6V.
4 FB input Feedback input to the error amplifier, connected through an external resistive divider and compared to the internal +0.8V reference to set the regulation voltage.
5 GND power_in Ground, connected as close as possible to the output capacitor, with the exposed pad connected to the GND plane for optimal thermal performance.
6 FREQ input Switching frequency program input, where a resistor from this pin to ground sets the switching frequency up to 2MHz.
7 VIN power_in Input supply that powers the internal control circuitry, both BS regulators and the high-side switch, over the 3.8V to 55V recommended supply range.
8 BST power_in Bootstrap positive supply for the internal floating high-side MOSFET driver, with a bypass capacitor connected between this pin and the SW pin.
9 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Monolithic Power Systems
Package SOIC-8-EP
Category Power Management
Pins 9

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Feedback Voltage VFB 0.78 0.8 0.82 V 4.5V < VIN < 55V, TJ=25°C 3
Feedback Voltage (over temperature) VFB 0.772 0.829 V 4.5V < VIN < 55V 3
Feedback Leakage Current IFB 0.1 1 µA 3
Upper Switch On Resistance RDS(ON) 175 250 330 mΩ VBST, VSW = 5V, TJ=25°C 3
Upper Switch On Resistance (over temperature) RDS(ON) 160 400 mΩ VBST, VSW = 5V 3
Upper Switch Leakage Current ISW 1 µA VEN = 0V, VSW = 0V 3
Current Limit ILIM 1.3 1.9 3.5 A TJ=25°C, duty cycle ≤60% 3
Current Limit (over temperature) ILIM 1.1 3.7 A Duty cycle ≤60% 3
COMP to Current Sense Transconductance GCS 5.7 A/V 3
Error Amp Voltage Gain 400 V/V 3
Error Amp Transconductance 120 µA/V ICOMP = ±3µA 3
Error Amp Min Source Current 10 µA VFB = 0.7V 3
Error Amp Min Sink Current -10 µA VFB = 0.9V 3
VIN UVLO Threshold 2.7 3 3.3 V TJ=25°C 3
VIN UVLO Threshold (over temperature) 2.4 3.6 V 3
VIN UVLO Hysteresis 0.35 V 3
Soft-Start Time 0.5 ms 0V < VFB < 0.8V 3
Oscillator Frequency fSW 0.8 1 1.2 MHz RFREQ = 95kΩ, TJ=25°C 3
Oscillator Frequency (over temperature) fSW 0.7 1.3 MHz RFREQ = 95kΩ 3
Shutdown Supply Current IS 12 20 µA VEN < 0.3V 3
Quiescent Supply Current IQ 140 200 µA No load, VFB = 0.9V (no switching) 3
Thermal Shutdown 150 °C Hysteresis = 20°C 3
Minimum Off Time tOFF 100 ns 3
Minimum On Time tON 100 ns 3
EN Rising Threshold 1.4 1.55 1.7 V TJ=25°C 3
EN Rising Threshold (over temperature) 1.3 1.8 V 3
EN Threshold Hysteresis 320 mV 3
Supply Voltage VIN -0.3 60 V 2
Switch Voltage VSW -0.5 V Max is VIN + 0.5V 2
BST to SW Voltage -0.3 5 V 2
All Other Pins Voltage -0.3 5 V 2
Continuous Power Dissipation PD 2.5 W TJ = +25°C, SOIC8E 2
Junction Temperature TJ 150 °C 2
Storage Temperature TSTG -65 150 °C 2
Supply Voltage VIN 3.8 55 V 2
Output Voltage VOUT 0.8 52 V 2
Operating Junction Temperature TJ -40 125 °C 2
Junction-to-Case Thermal Resistance θJC 10 °C/W SOIC8 (Exposed Pad) 2

CAD (KiCad official)

  • Symbol: MP4558DN-LF-Z
  • Footprint: Package_SO:SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.29x3mm
  • 3D model: SOIC-8-EP (KiCad packages3D, STEP)
  • 3D model files: mp4558dn-lf-z-etched.step / mp4558dn-lf-z-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); mp4558dn-lf-z.step / mp4558dn-lf-z.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Monolithic Power Systems datasheet (20 pp, sha256 e31e175dd5dd7381, retrieved 2026-11-02, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF