main
Ray
Publish 0.1.0
0e95780
MP4436AGR-Z
Monolithic Power Systems · DC-DC Converters · QFN-20(4x4)
MP4436AGR-Z from Monolithic Power Systems, in a QFN-20(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | MODE | input | Pull MODE high to force forced continuous conduction mode (FCCM) and low for advanced asynchronous mode (AAM) under light load; do not float MODE. |
| 2 | SYNCIN | input | Accepts a 350kHz to 530kHz clock to synchronize the internal oscillator, with a 51kΩ resistor to GND; tie to GND if unused and do not float. |
| 3 | VIN | power_in | Input supply for the control circuitry and the power switch, operating from 3.3V to 45V, with a decoupling capacitor placed close to VIN. |
| 4 | PGND | power_in | Power ground for the internal power switch. |
| 5 | PGND | power_in | Power ground for the internal power switch. |
| 6 | BST | power_out | Bootstrap positive supply for the high-side MOSFET driver, requiring a bypass capacitor connected between BST and SW. |
| 7 | SW | power_out | Switch node, the output of the internal power switch. |
| 8 | SW | power_out | Switch node, the output of the internal power switch. |
| 9 | EN | input | Enable pin; pulling it below the 0.85V threshold shuts down the chip and pulling it above the 1V threshold enables it. |
| 10 | PGND | power_in | Power ground for the internal power switch. |
| 11 | PGND | power_in | Power ground for the internal power switch. |
| 12 | VIN | power_in | Input supply for the control circuitry and the power switch, operating from 3.3V to 45V, with a decoupling capacitor placed close to VIN. |
| 13 | SYNCO | output | Outputs a clock signal 180° out of phase with the internal oscillator or opposite the SYNCIN clock; float if not used. |
| 14 | PG | output | Open-drain power good output that goes high when VOUT is within 93% to 106% of nominal and goes low above 107.5% or below 91%, requiring a pull-up resistor when used. |
| 15 | ICS | input | Current sharing pin, connected in parallel for multi-phase operation or to VCC or VOUT above 3V in single-phase operation; do not float. |
| 16 | VCC | power_in | Bias supply for the internal control circuit and gate drivers, requiring a decoupling capacitor placed close to this pin. |
| 17 | AGND | power_in | Analog ground. |
| 18 | FB | input | Feedback input with a 0.815V threshold, connected to the center point of the output resistor divider and placed as close to FB as possible. |
| 19 | SS | passive | Soft-start input; a capacitor from SS to GND sets the soft-start period, with 6µA sourced from the pin during start-up. |
| 20 | FREQ | input | Switching frequency program; a resistor from this pin to ground sets the frequency per the fSW vs. RFREQ curve. |
| 21 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Monolithic Power Systems |
| Package | QFN-20(4x4) |
| Category | Power Supply Chip |
| Pins | 21 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Wide operating input voltage range | VIN | 3.3 | 45 | V | 5 | ||
| Operating junction temperature | TJ | -40 | 125 | °C | 5 | ||
| Supply voltage absolute maximum (VIN, EN) | VIN, EN | -0.3 | 50 | V | 5 | ||
| All other pins absolute maximum | -0.3 | 6 | V | All other pins | 5 | ||
| Operating junction temperature absolute maximum | 150 | °C | 5 | ||||
| Lead temperature | 260 | °C | 5 | ||||
| Storage temperature | -65 | 150 | °C | 5 | |||
| ESD human body model | -2 | 2 | kV | Human body model (HBM) | 5 | ||
| ESD charged device model | -750 | 750 | V | Charged device model (CDM) | 5 | ||
| Continuous power dissipation | PD | 2.84 | W | TA = 25°C, QFN-20 (4mmx4mm) | 5 | ||
| Thermal resistance junction-to-case | θJC | 9 | °C/W | QFN-20 (4mmx4mm), JESD51-7, 4-layer PCB | 5 | ||
| Thermal resistance junction-to-case (EVQ board) | θJC | 2.5 | °C/W | EVQ4436-R-00A, 9cmx9cm, 4-layer PCB | 5 | ||
| VIN UVLO rising threshold | INUVLO_RISING | 2.8 | 3 | 3.2 | V | 6 | |
| VIN UVLO falling threshold | INUVLO_FALLING | 2.45 | 2.65 | 2.85 | V | 6 | |
| VCC voltage | VCC | 4.6 | 4.9 | 5.2 | V | IVCC = 0A | 6 |
| VIN quiescent current (sleep mode) | IQ | 18 | 26 | μA | FB = 0.85V, no load (sleep mode) | 6 | |
| VIN shutdown current | ISHDN | 1.7 | 2.5 | μA | EN = 0V | 6 | |
| FB voltage | VFB | 0.807 | 0.815 | 0.823 | V | VIN = 3.3V to 45V, TJ = 25°C | 6 |
| FB voltage | VFB | 0.799 | 0.815 | 0.831 | V | VIN = 3.3V to 45V | 6 |
| FB current | IFB | -50 | 0 | 50 | nA | VFB = 0.85V | 6 |
| Switching frequency | fSW | 420 | 470 | 520 | kHz | RFREQ = 62kΩ | 6 |
| SYNCIN clock range | fSYNC | 350 | 530 | kHz | External clock | 6 | |
| SYNCO high voltage | VSYNCO_HIGH | 3.3 | 4.5 | V | ISYNCO = -1mA | 6 | |
| HS current limit | ILIMIT | 10 | 13 | 16 | A | Duty cycle = 30% | 6 |
| LS valley current limit | ILIMIT_VALLEY | 8 | 10 | 12 | A | 6 | |
| ZCD current | IZCD | -0.15 | 0.1 | 0.35 | A | AAM | 6 |
| LS reverse current limit | ILIMIT_REVERSE | 2 | 4.5 | 6.5 | A | FCCM | 6 |
| Switch leakage current | ISW_LKG | 0.01 | 1 | µA | 7 | ||
| HS switch on resistance | RON_HS | 48 | 80 | mΩ | VBST - VSW = 5V | 7 | |
| LS switch on resistance | RON_LS | 20 | 40 | mΩ | VCC = 5V | 7 | |
| Soft-start current | ISS | 4 | 6 | 8 | µA | VSS = 0V | 7 |
| EN rising threshold | VEN_RISING | 0.8 | 1 | 1.2 | V | 7 | |
| EN falling threshold | VEN_FALLING | 0.65 | 0.85 | 1.05 | V | 7 | |
| PG rising threshold (VFB rising) | PGRISING | 88.5 | 93 | 97.5 | % | VFB rising, % of VREF | 7 |
| PG rising threshold (VFB falling) | PGRISING | 101.5 | 106 | 110.5 | % | VFB falling, % of VREF | 7 |
| PG falling threshold (VFB falling) | PGFALLING | 86.5 | 91 | 95.5 | % | VFB falling, % of VREF | 7 |
| PG falling threshold (VFB rising) | PGFALLING | 103 | 107.5 | 112 | % | VFB rising, % of VREF | 7 |
| PG output voltage low | VPG_LOW | 0.1 | 0.3 | V | ISINK = 1mA | 7 |
CAD (KiCad official)
- Symbol:
MP4436AGR-Z - Footprint:
Package_DFN_QFN:QFN-20-1EP_4x4mm_P0.5mm_EP2.5x2.5mm - 3D model: QFN-20(4x4) (KiCad packages3D, STEP)
- 3D model files:
mp4436agr-z-etched.step/mp4436agr-z-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mp4436agr-z.step/mp4436agr-z.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Monolithic Power Systems datasheet (38 pp, sha256
72c172785dcd23fd, retrieved 2026-10-26, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusoff(skipped (clean text read)), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# MP4436AGR-Z
**Monolithic Power Systems** · DC-DC Converters · QFN-20(4x4)
MP4436AGR-Z from Monolithic Power Systems, in a QFN-20(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | MODE | input | Pull MODE high to force forced continuous conduction mode (FCCM) and low for advanced asynchronous mode (AAM) under light load; do not float MODE. |
| 2 | SYNCIN | input | Accepts a 350kHz to 530kHz clock to synchronize the internal oscillator, with a 51kΩ resistor to GND; tie to GND if unused and do not float. |
| 3 | VIN | power_in | Input supply for the control circuitry and the power switch, operating from 3.3V to 45V, with a decoupling capacitor placed close to VIN. |
| 4 | PGND | power_in | Power ground for the internal power switch. |
| 5 | PGND | power_in | Power ground for the internal power switch. |
| 6 | BST | power_out | Bootstrap positive supply for the high-side MOSFET driver, requiring a bypass capacitor connected between BST and SW. |
| 7 | SW | power_out | Switch node, the output of the internal power switch. |
| 8 | SW | power_out | Switch node, the output of the internal power switch. |
| 9 | EN | input | Enable pin; pulling it below the 0.85V threshold shuts down the chip and pulling it above the 1V threshold enables it. |
| 10 | PGND | power_in | Power ground for the internal power switch. |
| 11 | PGND | power_in | Power ground for the internal power switch. |
| 12 | VIN | power_in | Input supply for the control circuitry and the power switch, operating from 3.3V to 45V, with a decoupling capacitor placed close to VIN. |
| 13 | SYNCO | output | Outputs a clock signal 180° out of phase with the internal oscillator or opposite the SYNCIN clock; float if not used. |
| 14 | PG | output | Open-drain power good output that goes high when VOUT is within 93% to 106% of nominal and goes low above 107.5% or below 91%, requiring a pull-up resistor when used. |
| 15 | ICS | input | Current sharing pin, connected in parallel for multi-phase operation or to VCC or VOUT above 3V in single-phase operation; do not float. |
| 16 | VCC | power_in | Bias supply for the internal control circuit and gate drivers, requiring a decoupling capacitor placed close to this pin. |
| 17 | AGND | power_in | Analog ground. |
| 18 | FB | input | Feedback input with a 0.815V threshold, connected to the center point of the output resistor divider and placed as close to FB as possible. |
| 19 | SS | passive | Soft-start input; a capacitor from SS to GND sets the soft-start period, with 6µA sourced from the pin during start-up. |
| 20 | FREQ | input | Switching frequency program; a resistor from this pin to ground sets the frequency per the fSW vs. RFREQ curve. |
| 21 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Monolithic Power Systems |
| Package | QFN-20(4x4) |
| Category | Power Supply Chip |
| Pins | 21 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Wide operating input voltage range | VIN | 3.3 | | 45 | V | | 5 |
| Operating junction temperature | TJ | -40 | | 125 | °C | | 5 |
| Supply voltage absolute maximum (VIN, EN) | VIN, EN | -0.3 | | 50 | V | | 5 |
| All other pins absolute maximum | | -0.3 | | 6 | V | All other pins | 5 |
| Operating junction temperature absolute maximum | | | | 150 | °C | | 5 |
| Lead temperature | | | | 260 | °C | | 5 |
| Storage temperature | | -65 | | 150 | °C | | 5 |
| ESD human body model | | -2 | | 2 | kV | Human body model (HBM) | 5 |
| ESD charged device model | | -750 | | 750 | V | Charged device model (CDM) | 5 |
| Continuous power dissipation | PD | | | 2.84 | W | TA = 25°C, QFN-20 (4mmx4mm) | 5 |
| Thermal resistance junction-to-case | θJC | | 9 | | °C/W | QFN-20 (4mmx4mm), JESD51-7, 4-layer PCB | 5 |
| Thermal resistance junction-to-case (EVQ board) | θJC | | 2.5 | | °C/W | EVQ4436-R-00A, 9cmx9cm, 4-layer PCB | 5 |
| VIN UVLO rising threshold | INUVLO_RISING | 2.8 | 3 | 3.2 | V | | 6 |
| VIN UVLO falling threshold | INUVLO_FALLING | 2.45 | 2.65 | 2.85 | V | | 6 |
| VCC voltage | VCC | 4.6 | 4.9 | 5.2 | V | IVCC = 0A | 6 |
| VIN quiescent current (sleep mode) | IQ | | 18 | 26 | μA | FB = 0.85V, no load (sleep mode) | 6 |
| VIN shutdown current | ISHDN | | 1.7 | 2.5 | μA | EN = 0V | 6 |
| FB voltage | VFB | 0.807 | 0.815 | 0.823 | V | VIN = 3.3V to 45V, TJ = 25°C | 6 |
| FB voltage | VFB | 0.799 | 0.815 | 0.831 | V | VIN = 3.3V to 45V | 6 |
| FB current | IFB | -50 | 0 | 50 | nA | VFB = 0.85V | 6 |
| Switching frequency | fSW | 420 | 470 | 520 | kHz | RFREQ = 62kΩ | 6 |
| SYNCIN clock range | fSYNC | 350 | | 530 | kHz | External clock | 6 |
| SYNCO high voltage | VSYNCO_HIGH | | 3.3 | 4.5 | V | ISYNCO = -1mA | 6 |
| HS current limit | ILIMIT | 10 | 13 | 16 | A | Duty cycle = 30% | 6 |
| LS valley current limit | ILIMIT_VALLEY | 8 | 10 | 12 | A | | 6 |
| ZCD current | IZCD | -0.15 | 0.1 | 0.35 | A | AAM | 6 |
| LS reverse current limit | ILIMIT_REVERSE | 2 | 4.5 | 6.5 | A | FCCM | 6 |
| Switch leakage current | ISW_LKG | | 0.01 | 1 | µA | | 7 |
| HS switch on resistance | RON_HS | | 48 | 80 | mΩ | VBST - VSW = 5V | 7 |
| LS switch on resistance | RON_LS | | 20 | 40 | mΩ | VCC = 5V | 7 |
| Soft-start current | ISS | 4 | 6 | 8 | µA | VSS = 0V | 7 |
| EN rising threshold | VEN_RISING | 0.8 | 1 | 1.2 | V | | 7 |
| EN falling threshold | VEN_FALLING | 0.65 | 0.85 | 1.05 | V | | 7 |
| PG rising threshold (VFB rising) | PGRISING | 88.5 | 93 | 97.5 | % | VFB rising, % of VREF | 7 |
| PG rising threshold (VFB falling) | PGRISING | 101.5 | 106 | 110.5 | % | VFB falling, % of VREF | 7 |
| PG falling threshold (VFB falling) | PGFALLING | 86.5 | 91 | 95.5 | % | VFB falling, % of VREF | 7 |
| PG falling threshold (VFB rising) | PGFALLING | 103 | 107.5 | 112 | % | VFB rising, % of VREF | 7 |
| PG output voltage low | VPG_LOW | | 0.1 | 0.3 | V | ISINK = 1mA | 7 |
## CAD (KiCad official)
- Symbol: `MP4436AGR-Z`
- Footprint: `Package_DFN_QFN:QFN-20-1EP_4x4mm_P0.5mm_EP2.5x2.5mm`
- 3D model: QFN-20(4x4) (KiCad packages3D, STEP)
- 3D model files: `mp4436agr-z-etched.step` / `mp4436agr-z-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `mp4436agr-z.step` / `mp4436agr-z.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Monolithic Power Systems datasheet](docs/mp4436agr-z-datasheet.pdf) (38 pp, sha256 `72c172785dcd23fd`, retrieved 2026-10-26, tier: lcsc)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `off` (skipped (clean text read)), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/mp4436agr-z-datasheet.pdf)