main
History Download
Ray Publish 0.1.0 7ac14c5

MP4420HGJ-Z

Monolithic Power Systems · DC-DC Converters · TSOT-23-8

MP4420HGJ-Z from Monolithic Power Systems, in a TSOT-23-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 PG output Open-drain power-good output that goes high when the output voltage exceeds 90% of nominal, pulled up through a resistor (e.g. 100kΩ).
2 IN power_in Supply voltage input that operates from a 4V to 36V rail and requires input capacitor C1 for decoupling, connected with a wide PCB trace.
3 SW output Switch output node connected using a wide PCB trace.
4 GND power_in System ground and reference ground of the regulated output voltage, connected with copper traces and vias.
5 BST passive Bootstrap pin requiring a capacitor to SW to form a floating supply for the high-side switch driver, with a 20Ω resistor in series strongly recommended to reduce SW spike voltage.
6 EN/SYNC input Enable input (high enables the part) that also accepts an external clock of 200kHz to 2.2MHz to set the switching frequency.
7 VCC power_out Internal 5V bias supply output to be decoupled with a 0.1μF to 0.22μF capacitor not exceeding 0.22μF.
8 FB input Feedback input connected to the tap of an external resistor divider from the output to GND to set the output voltage, with frequency fold-back when FB is below 660mV.

Key specifications

Parameter Value
Manufacturer Monolithic Power Systems
Package TSOT-23-8
Category Power Management
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input voltage VIN -0.3 40 V 3
Switch voltage VSW -0.3 41 V 3
All other pins -0.3 6 V 3
Continuous power dissipation 1.25 W TA = +25°C, TSOT23-8 3
Junction temperature TJ 150 °C 3
Lead temperature 260 °C 3
Storage temperature -65 150 °C 3
Continuous supply voltage VIN 4 36 V 3
Output voltage VOUT 0.8 V 0.8V to 0.9xVIN 3
Operating junction temperature TJ -40 125 °C 3
Quiescent supply current IQ 0.5 0.7 mA VEN = 2V, VFB = 1V 4
HS switch on-resistance RON_HS 90 105 mΩ VBST-SW=5V 4
LS switch on-resistance RON_LS 55 75 mΩ VCC =5V 4
Current limit ILIMIT 3.2 4.2 5.3 A Under 40% Duty Cycle 4
Oscillator frequency fSW 320 410 500 kHz VFB=750mV 4
Fold-back frequency fFB 70 100 130 kHz VFB<400mV 4
Maximum duty cycle DMAX 92 95 % VFB=750mV, 410kHz 4
Sync frequency range fSYNC 0.2 2.4 MHz 4
Feedback voltage VFB 780 792 804 mV 4
Feedback current IFB 10 100 nA VFB=820mV 4
EN rising threshold VEN RISING 1.15 1.4 1.65 V 4
EN falling threshold VEN FALLING 1.05 1.25 1.45 V 4
EN input current IEN 4 6 μA VEN=2V 4
EN input current IEN 0 0.2 μA VEN=0 4
VIN UVLO threshold rising INUVRISING 3.3 3.5 3.7 V 4
VIN UVLO threshold falling INUVFALLING 3.1 3.3 3.5 V 4
VCC regulator VCC 4.6 4.9 5.2 V ICC=0mA 4
VCC load regulation 1.5 4 % ICC=5mA 4
Soft-start period tSS 0.55 1.45 2.45 ms VOUT from 10% to 90% 4
Thermal shutdown 150 170 °C 4
PG rising threshold PGVth RISING 86.5 90 93.5 % as percentage of VFB 4
PG falling threshold PGVth FALLING 80.5 84 87.5 % as percentage of VFB 4
PG rising delay PGTd_RISING 40 90 160 μs 5
PG falling delay PGTd_FALLING 30 55 95 μs 5
PG sink voltage VPG 0.1 0.3 V Sink 4mA 5
PG leakage current ILKG_PG 10 100 nA 5
Shutdown supply current ISHDN 8 μA VEN = 0V 4
Switch leakage ILKG SW 1 μA VEN = 0V, VSW =12V 4
Minimum on time tON MIN 70 ns 4
EN threshold hysteresis VEN_HYS 150 mV 4
VIN UVLO hysteresis INUVHYS 200 mV 4
Thermal hysteresis 30 °C 4
PG threshold hysteresis PGVth_HYS 6 % as percentage of VFB 5
Thermal resistance junction-ambient θJA 100 °C/W TSOT23-8, JESD51-7 4-layer PCB 3
Thermal resistance junction-case θJC 55 °C/W TSOT23-8, JESD51-7 4-layer PCB 3

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts copper 4 GND System Ground. This pin is the reference ground of the regulated output voltage, and PCB layout requires special care. For best results, connect to GND with copper traces and vias. 12

CAD (KiCad official)

  • Symbol: MP4420HGJ-Z
  • Footprint: Package_TO_SOT_SMD:TSOT-23-8
  • 3D model: TSOT-23-8 (KiCad packages3D, STEP)
  • 3D model files: mp4420hgj-z-etched.step / mp4420hgj-z-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); mp4420hgj-z.step / mp4420hgj-z.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Monolithic Power Systems datasheet (20 pp, sha256 c68628245baef462, retrieved 2026-10-24, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF