main
Ray
Publish 0.1.0
2b6e3da
MP3309GQG-Z
Monolithic Power Systems · LED Drivers · QFN-10(1.4x1.8)
MP3309GQG-Z from Monolithic Power Systems, in a QFN-10(1.4x1.8). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | PWMH | input | Dimming input for PWM-input analog dimming (>20kHz PWM signal recommended); pull both PWMH pins high together when analog dimming is not used. |
| 2 | VIN | power_in | Input supply pin (2.7V to 5.5V) that powers internal power and logic circuits and must be locally bypassed. |
| 3 | EN/PWML | input | PWM brightness control/enable input, 200Hz to 2kHz recommended for PWM dimming, where a low-level signal longer than 20ms shuts down the IC. |
| 4 | FREQ | passive | Switching frequency set pin; connect a resistor between this pin and GND to program the converter switching frequency and do not leave it floating. |
| 5 | FB | input | LED current feedback pin that regulates the voltage across the current sense resistor between FB and GND to 200mV; do not leave floating. |
| 6 | GND | power_in | Ground. |
| 7 | SW | passive | Power switch node, drain of the internal low-side MOSFET; connect the power inductor between SW and VIN, and a Schottky diode to VOUT for non-synchronous mode. |
| 8 | VOUT | power_out | Output voltage pin internally connected to the source of the synchronous MOSFET (OVP threshold typically 35.5V); for non-synchronous mode connect a Schottky diode between SW and this pin. |
| 9 | BST | passive | Bootstrap pin; connect a capacitor between SW and BST to provide the synchronous MOSFET gate driver. |
| 10 | PWMH | input | Dimming input for PWM-input analog dimming (>20kHz PWM signal recommended); pull both PWMH pins high together when analog dimming is not used. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Monolithic Power Systems |
| Package | QFN-10(1.4x1.8) |
| Category | LED Drivers |
| Pins | 10 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input Voltage (Supply) | VIN | 2.7 | 5.5 | V | 2 | ||
| Operating Junction Temperature | TJ | -40 | 125 | °C | 2 | ||
| VIN absolute maximum | VIN | -0.3 | 6 | V | 2 | ||
| SW and VOUT absolute maximum | VSW, VOUT | -1 | 40 | V | 2 | ||
| BST absolute maximum | VBST | -0.3 | 6 | V | VSW + 6V upper limit (relative to VSW) | 2 | |
| All Other Pins absolute maximum | -0.3 | 6 | V | 2 | |||
| Junction Temperature | TJ | 150 | °C | 2 | |||
| Thermal Resistance Junction-Ambient | θJA | 140 | °C/W | QFN-10 (1.4mmx1.8mm), JESD51-7 4-layer PCB | 2 | ||
| Thermal Resistance Junction-Case | θJC | 30 | °C/W | QFN-10 (1.4mmx1.8mm), JESD51-7 4-layer PCB | 2 | ||
| Operating Input Voltage | VIN | 2.7 | 5.5 | V | 3 | ||
| Supply Current (Quiescent) | IQ | 420 | μA | VIN=3.6V, VEN= VIN, no load with switching | 3 | ||
| Supply Current (Shutdown) | IST | 1 | μA | VEN=0V, VIN=3.6V | 3 | ||
| Supply Current (Shutdown) | IST | 68 | μA | EN Bit=0, VIN=3.6V | 3 | ||
| Input UVLO Threshold | VIN_UVLO | 2.5 | V | Rising Edge | 3 | ||
| Input UVLO Hysteresis | 200 | mV | 3 | ||||
| EN High Voltage | VEN_HIGH | 1.2 | V | VEN Rising | 3 | ||
| EN Low Voltage | VEN_LOW | 0.4 | V | VEN Falling | 3 | ||
| Switching Frequency | fSW | 540 | 640 | 740 | kHz | ROSC= 200kΩ | 3 |
| Maximum Duty Cycle | DMAX | 89 | 93 | % | Sync Mode, 600kHz | 3 | |
| Feedback Regulation Voltage | VREF | 198 | 200 | 202 | mV | 3 | |
| Main Switch On-Resistance | RDSON_M | 0.3 | 0.5 | Ω | VIN=3.6V | 3 | |
| Sync Switch On-Resistance | RDSON_S | 0.5 | 0.8 | Ω | VIN=3.6V | 3 | |
| PWMH Input Low Threshold | VPWM_LO | 0.4 | V | VPWM Falling | 3 | ||
| PWMH Input High Threshold | VPWM_HI | 1.2 | V | VPWM Rising | 3 | ||
| EN/PWML Shutdown Time | tSD | 20 | ms | EN/PWML High to Low | 3 | ||
| OVP Voltage | VOVP | 33.5 | 35.5 | 37.5 | V | 3 | |
| OVP Hysteresis | 2.5 | V | Hysteresis | 3 | |||
| Cycle-Cycle Current Limit | ILIM | 1.5 | A | Max Duty Cycle | 3 | ||
| Startup Current Limit | ILIM_START | 0.8 | A | Max Duty Cycle | 3 | ||
| Time Step for Half Current Limit | TLIM_HALF | 5 | ms | 3 | |||
| OVP UVLO Threshold | VOVP_UV | 1.24 | V | 3 | |||
| Thermal Shutdown Threshold | tST | 150 | °C | 3 | |||
| Thermal Shutdown Hysteresis | 25 | °C | 3 |
CAD (KiCad official)
- Symbol:
MP3309GQG-Z - Footprint:
Package_DFN_QFN:UQFN-10_1.4x1.8mm_P0.4mm - 3D model: QFN-10(1.4x1.8) (KiCad packages3D, STEP)
- 3D model files:
mp3309gqg-z-etched.step/mp3309gqg-z-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mp3309gqg-z.step/mp3309gqg-z.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Monolithic Power Systems datasheet (12 pp, sha256
e5b06a74e0f88963, retrieved 2026-10-27, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# MP3309GQG-Z
**Monolithic Power Systems** · LED Drivers · QFN-10(1.4x1.8)
MP3309GQG-Z from Monolithic Power Systems, in a QFN-10(1.4x1.8). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | PWMH | input | Dimming input for PWM-input analog dimming (>20kHz PWM signal recommended); pull both PWMH pins high together when analog dimming is not used. |
| 2 | VIN | power_in | Input supply pin (2.7V to 5.5V) that powers internal power and logic circuits and must be locally bypassed. |
| 3 | EN/PWML | input | PWM brightness control/enable input, 200Hz to 2kHz recommended for PWM dimming, where a low-level signal longer than 20ms shuts down the IC. |
| 4 | FREQ | passive | Switching frequency set pin; connect a resistor between this pin and GND to program the converter switching frequency and do not leave it floating. |
| 5 | FB | input | LED current feedback pin that regulates the voltage across the current sense resistor between FB and GND to 200mV; do not leave floating. |
| 6 | GND | power_in | Ground. |
| 7 | SW | passive | Power switch node, drain of the internal low-side MOSFET; connect the power inductor between SW and VIN, and a Schottky diode to VOUT for non-synchronous mode. |
| 8 | VOUT | power_out | Output voltage pin internally connected to the source of the synchronous MOSFET (OVP threshold typically 35.5V); for non-synchronous mode connect a Schottky diode between SW and this pin. |
| 9 | BST | passive | Bootstrap pin; connect a capacitor between SW and BST to provide the synchronous MOSFET gate driver. |
| 10 | PWMH | input | Dimming input for PWM-input analog dimming (>20kHz PWM signal recommended); pull both PWMH pins high together when analog dimming is not used. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Monolithic Power Systems |
| Package | QFN-10(1.4x1.8) |
| Category | LED Drivers |
| Pins | 10 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input Voltage (Supply) | VIN | 2.7 | | 5.5 | V | | 2 |
| Operating Junction Temperature | TJ | -40 | | 125 | °C | | 2 |
| VIN absolute maximum | VIN | -0.3 | | 6 | V | | 2 |
| SW and VOUT absolute maximum | VSW, VOUT | -1 | | 40 | V | | 2 |
| BST absolute maximum | VBST | -0.3 | | 6 | V | VSW + 6V upper limit (relative to VSW) | 2 |
| All Other Pins absolute maximum | | -0.3 | | 6 | V | | 2 |
| Junction Temperature | TJ | | | 150 | °C | | 2 |
| Thermal Resistance Junction-Ambient | θJA | | 140 | | °C/W | QFN-10 (1.4mmx1.8mm), JESD51-7 4-layer PCB | 2 |
| Thermal Resistance Junction-Case | θJC | | 30 | | °C/W | QFN-10 (1.4mmx1.8mm), JESD51-7 4-layer PCB | 2 |
| Operating Input Voltage | VIN | 2.7 | | 5.5 | V | | 3 |
| Supply Current (Quiescent) | IQ | | 420 | | μA | VIN=3.6V, VEN= VIN, no load with switching | 3 |
| Supply Current (Shutdown) | IST | | 1 | | μA | VEN=0V, VIN=3.6V | 3 |
| Supply Current (Shutdown) | IST | | 68 | | μA | EN Bit=0, VIN=3.6V | 3 |
| Input UVLO Threshold | VIN_UVLO | | 2.5 | | V | Rising Edge | 3 |
| Input UVLO Hysteresis | | | 200 | | mV | | 3 |
| EN High Voltage | VEN_HIGH | | 1.2 | | V | VEN Rising | 3 |
| EN Low Voltage | VEN_LOW | | 0.4 | | V | VEN Falling | 3 |
| Switching Frequency | fSW | 540 | 640 | 740 | kHz | ROSC= 200kΩ | 3 |
| Maximum Duty Cycle | DMAX | 89 | 93 | | % | Sync Mode, 600kHz | 3 |
| Feedback Regulation Voltage | VREF | 198 | 200 | 202 | mV | | 3 |
| Main Switch On-Resistance | RDSON_M | | 0.3 | 0.5 | Ω | VIN=3.6V | 3 |
| Sync Switch On-Resistance | RDSON_S | | 0.5 | 0.8 | Ω | VIN=3.6V | 3 |
| PWMH Input Low Threshold | VPWM_LO | | 0.4 | | V | VPWM Falling | 3 |
| PWMH Input High Threshold | VPWM_HI | | 1.2 | | V | VPWM Rising | 3 |
| EN/PWML Shutdown Time | tSD | | 20 | | ms | EN/PWML High to Low | 3 |
| OVP Voltage | VOVP | 33.5 | 35.5 | 37.5 | V | | 3 |
| OVP Hysteresis | | | 2.5 | | V | Hysteresis | 3 |
| Cycle-Cycle Current Limit | ILIM | | 1.5 | | A | Max Duty Cycle | 3 |
| Startup Current Limit | ILIM_START | | 0.8 | | A | Max Duty Cycle | 3 |
| Time Step for Half Current Limit | TLIM_HALF | | 5 | | ms | | 3 |
| OVP UVLO Threshold | VOVP_UV | | 1.24 | | V | | 3 |
| Thermal Shutdown Threshold | tST | | 150 | | °C | | 3 |
| Thermal Shutdown Hysteresis | | | 25 | | °C | | 3 |
## CAD (KiCad official)
- Symbol: `MP3309GQG-Z`
- Footprint: `Package_DFN_QFN:UQFN-10_1.4x1.8mm_P0.4mm`
- 3D model: QFN-10(1.4x1.8) (KiCad packages3D, STEP)
- 3D model files: `mp3309gqg-z-etched.step` / `mp3309gqg-z-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `mp3309gqg-z.step` / `mp3309gqg-z.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Monolithic Power Systems datasheet](docs/mp3309gqg-z-datasheet.pdf) (12 pp, sha256 `e5b06a74e0f88963`, retrieved 2026-10-27, tier: lcsc)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/mp3309gqg-z-datasheet.pdf)