main
Ray
Publish 0.1.0
6ae1791
MP2635AGR-Z
Monolithic Power Systems · Battery Management ICs · QFN-24(4x4)
MP2635AGR-Z from Monolithic Power Systems, in a QFN-24(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | FREQ | input | Connect to GND to program the operating frequency to 600kHz; leave floating or connect to HIGH for 1.2MHz. |
| 2 | VIN | power_in | Adapter input; place a bypass capacitor close to this pin to prevent large input voltage spikes (absolute max 20V). |
| 3 | VCC | power_out | Internal circuit power supply; bypass to GND with a 100nF ceramic capacitor and do not load it with more than 5mA. |
| 4 | ILIM | passive | Input current set; connect an external resistor to GND to program the input current limit in charge mode. |
| 5 | PWIN | input | AC input detect; detects the presence of valid input power (valid window about 0.8V to 1.15V). |
| 6 | TMR | passive | Oscillator period timer; connect a timing capacitor to GND to set the oscillator period, or short to GND to disable the timer function. |
| 7 | REG | input | Input voltage feedback; connect to the tap of an external resistor divider from VIN to GND, and the pin voltage should always exceed 1.2V during normal operation. |
| 8 | ACOK | output | Valid input supply indicator (active-low); logic LOW indicates the presence of a valid power supply. |
| 9 | FB | input | System voltage feedback input (1.2V typical feedback voltage in boost mode). |
| 10 | NTC | input | Negative temperature coefficient (NTC) thermistor input for battery temperature monitoring. |
| 11 | ISET | passive | Charge current set; connect an external resistor to GND to program the charge current. |
| 12 | OLIM | passive | Boost output-current limit set; connect an external resistor to GND to program the system current in boost mode. |
| 13 | AGND | power_in | Analog ground. |
| 14 | VB | power_in | Programmable battery-full voltage; connect to GND for 3.6V, or leave floating or connect to logic HIGH for 4.2V. |
| 15 | BATT | bidirectional | Positive battery terminal and battery charge current sense negative input. |
| 16 | CSP | input | Battery charge current sense positive input. |
| 17 | BOOST | output | Boost mode indicator (open drain); logic LOW indicates boost mode, and the pin is open drain in charge or sleep mode. |
| 18 | CHG | output | Charge completion indicator (open drain); logic LOW indicates charge mode, and the pin is open drain once charging has completed or is suspended. |
| 19 | PGND | power_in | Power ground and exposed pad; connect the exposed pad and the GND pin to the same ground plane. |
| 20 | SW | power_out | Switch output node. |
| 21 | SYS | power_out | System output (pins 21 and 22 are tied together); provide sufficient bulk capacitance from SYS to GND, at least 4.7µF suggested. |
| 22 | SYS | power_out | System output (pins 21 and 22 are tied together); provide sufficient bulk capacitance from SYS to GND, at least 4.7µF suggested. |
| 23 | MODE | input | Mode select; logic HIGH selects boost mode and logic LOW selects sleep mode, active only when ACOK is HIGH (input power not available). |
| 24 | EN | input | Charge control input; logic HIGH enables charging and logic LOW disables charging, active only when ACOK is low (input power OK). |
| 25 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Monolithic Power Systems |
| Package | QFN-24(4x4) |
| Category | Power Management |
| Pins | 25 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VCC UVLO | VCC UVLO | 2 | 2.2 | 2.4 | V | VIN = 5.0V, TA = 25°C | 4 |
| PWIN Lower Threshold | VPWIN L | 0.75 | 0.8 | 0.85 | V | 4 | |
| PWIN Upper Threshold | VPWIN H | 1.1 | 1.15 | 1.2 | V | 4 | |
| Input Current Limit | IIN_LIMIT | 400 | 450 | 500 | mA | RlLIM = 90.9k | 4 |
| Input Current Limit | IIN_LIMIT | 720 | 810 | 900 | mA | RlLIM = 49.9k | 4 |
| Input Current Limit | IIN_LIMIT | 2400 | 2700 | 3000 | mA | RlLIM = 15k | 4 |
| Terminal Battery Voltage | VBATT_FULL | 3.582 | 3.6 | 3.618 | V | Connect VB to GND | 4 |
| Terminal Battery Voltage | VBATT_FULL | 4.179 | 4.2 | 4.221 | V | Leave VB floating or connect to logic HIGH | 4 |
| Recharge Threshold | VRECH | 3.35 | 3.4 | 3.45 | V | Connect to VB to GND | 4 |
| Recharge Threshold | VRECH | 3.91 | 3.96 | 4.01 | V | Leave VB floating or connect to logic HIGH | 4 |
| Constant Charge Current | ICC | 900 | 1000 | 1100 | mA | RS1 = 40mΩ, RISET = 69.8k | 4 |
| Constant Charge Current | ICC | 1800 | 2000 | 2200 | mA | RS1 = 40mΩ, RISET = 34.9k | 4 |
| Trickle Charge Voltage Threshold | VBATT_TC | 2.47 | 2.57 | 2.67 | V | Connect to VB to GND | 5 |
| Trickle Charge Voltage Threshold | VBATT_TC | 2.9 | 3 | 3.1 | V | Leave VB floating or connect to high logic | 5 |
| Termination Charge Current | IBF | 5 | 10 | 15 | % ICC | 5 | |
| Input-Voltage-Regulation Reference | VREG | 1.18 | 1.2 | 1.22 | V | 5 | |
| Feedback Voltage | 1.18 | 1.2 | 1.22 | V | Boost Mode | 5 | |
| Boost SYS Over-Voltage Protection Threshold | VSYS(OVP) | 5.8 | 6 | 6.2 | V | Threshold over VSYS to turn off the converter during boost mode | 5 |
| Programmable Boost Output Current Limit Accuracy | IOLIM | 0.9 | 1 | 1.1 | A | RS1 = 40mΩ, ROLIM = 69.8k | 5 |
| Weak-Battery Threshold | VBATT(LOW) | 2.9 | 3.05 | V | Before Boost starts | 5 | |
| NTC Low Temp, Rising Threshold | 65 | 66 | 67 | % VSYS | RNTC=NCP18XH103(0ºC) | 6 | |
| NTC High Temp, Rising Threshold | 34 | 35 | 36 | % VSYS | RNTC=NCP18XH103(50ºC) | 6 | |
| Battery Leakage Current | ILEAKAGE | 15 | 30 | μA | VBATT = 4.2V, SYS Float, VIN = 0V, MODE = 0V | 5 | |
| Feedback Input Current | 200 | nA | VFB=1V | 5 | |||
| ACOK, CHG, BOOST pin output low voltage | 400 | mV | Sinking 1.5mA | 5 | |||
| ACOK, CHG, BOOST pin leakage current | 1 | μA | Connected to 5V | 5 | |||
| EN Input Logic Low Voltage | 0.4 | V | 5 | ||||
| EN Input High Voltage | 1.4 | V | 5 | ||||
| Mode Input Logic Low Voltage | 0.4 | V | 5 | ||||
| Mode Input Logic High Voltage | 1.4 | V | 5 | ||||
| IN to SYS NMOS ON Resistance | RIN to SYS | 100 | mΩ | 4 | |||
| High-side PMOS ON Resistance | RH DS | 72 | mΩ | 4 | |||
| Low-side NMOS ON Resistance | RL DS | 70 | mΩ | 4 | |||
| High-Side PMOS Peak Current Limit | IPEAK_HS | 3.6 | A | CC Charge Mode/ Boost Mode | 4 | ||
| High-Side PMOS Peak Current Limit | IPEAK_HS | 1.5 | A | TC Charge Mode | 4 | ||
| Low-Side NMOS Peak Current Limit | IPEAK_LS | 2.8 | A | 4 | |||
| Switching Frequency | fsw | 600 | kHz | FREQ = 0 | 4 | ||
| Switching Frequency | fsw | 1200 | kHz | FREQ = Float/ High | 4 | ||
| Input Quiescent Current | IIN | 2.5 | mA | EN = 5V, Battery Float | 4 | ||
| Input Quiescent Current | IIN | 1.5 | mA | EN = 0 | 4 | ||
| Input Over-Current Threshold | IIN(OCP) | 3 | A | 4 | |||
| Boost Quiescent Current | 1.4 | mA | ISYS = 0, MODE = 5V | 5 | |||
| Thermal Shutdown Threshold | 150 | °C | Guaranteed by design | 6 | |||
| Charging Current Foldback Threshold | 120 | °C | Charge Mode; guaranteed by design | 6 | |||
| Input Voltage VIN (absolute max) | VIN | -0.3 | 20 | V | 3 | ||
| SYS, SW voltage | SYS, SW | -0.3 | 6.5 | V | 3 | ||
| BATT voltage | BATT | -0.3 | 6.5 | V | 3 | ||
| ACOK, CHG, BOOST voltage | -0.3 | 6.5 | V | 3 | |||
| All Other Pins | -0.3 | 6.5 | V | 3 | |||
| Junction Temperature | TJ | 150 | °C | 3 | |||
| Lead Temperature | 260 | °C | 3 | ||||
| Continuous Power Dissipation | PD | 2.97 | W | TA = +25°C | 3 | ||
| Operating Temperature | -20 | 85 | °C | 3 | |||
| Supply Voltage VIN | VIN | 4.5 | 6 | V | 3 | ||
| Battery Voltage | VOUT | 2.5 | 4.35 | V | 3 | ||
| Operating Junction Temp. | TJ | -40 | 125 | °C | 3 | ||
| Thermal Resistance Junction-Ambient | θJA | 42 | °C/W | QFN24 (4×4mm), JESD51-7 4-layer PCB | 3 | ||
| Thermal Resistance Junction-Case | θJC | 9 | °C/W | QFN24 (4×4mm), JESD51-7 4-layer PCB | 3 |
CAD (KiCad official)
- Symbol:
MP2635AGR-Z - Footprint:
Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm - 3D model: QFN-24(4x4) (KiCad packages3D, STEP)
- 3D model files:
mp2635agr-z-etched.step/mp2635agr-z-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mp2635agr-z.step/mp2635agr-z.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Monolithic Power Systems datasheet (33 pp, sha256
96ef7759a25b17bd, retrieved 2026-10-23, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# MP2635AGR-Z
**Monolithic Power Systems** · Battery Management ICs · QFN-24(4x4)
MP2635AGR-Z from Monolithic Power Systems, in a QFN-24(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | FREQ | input | Connect to GND to program the operating frequency to 600kHz; leave floating or connect to HIGH for 1.2MHz. |
| 2 | VIN | power_in | Adapter input; place a bypass capacitor close to this pin to prevent large input voltage spikes (absolute max 20V). |
| 3 | VCC | power_out | Internal circuit power supply; bypass to GND with a 100nF ceramic capacitor and do not load it with more than 5mA. |
| 4 | ILIM | passive | Input current set; connect an external resistor to GND to program the input current limit in charge mode. |
| 5 | PWIN | input | AC input detect; detects the presence of valid input power (valid window about 0.8V to 1.15V). |
| 6 | TMR | passive | Oscillator period timer; connect a timing capacitor to GND to set the oscillator period, or short to GND to disable the timer function. |
| 7 | REG | input | Input voltage feedback; connect to the tap of an external resistor divider from VIN to GND, and the pin voltage should always exceed 1.2V during normal operation. |
| 8 | ACOK | output | Valid input supply indicator (active-low); logic LOW indicates the presence of a valid power supply. |
| 9 | FB | input | System voltage feedback input (1.2V typical feedback voltage in boost mode). |
| 10 | NTC | input | Negative temperature coefficient (NTC) thermistor input for battery temperature monitoring. |
| 11 | ISET | passive | Charge current set; connect an external resistor to GND to program the charge current. |
| 12 | OLIM | passive | Boost output-current limit set; connect an external resistor to GND to program the system current in boost mode. |
| 13 | AGND | power_in | Analog ground. |
| 14 | VB | power_in | Programmable battery-full voltage; connect to GND for 3.6V, or leave floating or connect to logic HIGH for 4.2V. |
| 15 | BATT | bidirectional | Positive battery terminal and battery charge current sense negative input. |
| 16 | CSP | input | Battery charge current sense positive input. |
| 17 | BOOST | output | Boost mode indicator (open drain); logic LOW indicates boost mode, and the pin is open drain in charge or sleep mode. |
| 18 | CHG | output | Charge completion indicator (open drain); logic LOW indicates charge mode, and the pin is open drain once charging has completed or is suspended. |
| 19 | PGND | power_in | Power ground and exposed pad; connect the exposed pad and the GND pin to the same ground plane. |
| 20 | SW | power_out | Switch output node. |
| 21 | SYS | power_out | System output (pins 21 and 22 are tied together); provide sufficient bulk capacitance from SYS to GND, at least 4.7µF suggested. |
| 22 | SYS | power_out | System output (pins 21 and 22 are tied together); provide sufficient bulk capacitance from SYS to GND, at least 4.7µF suggested. |
| 23 | MODE | input | Mode select; logic HIGH selects boost mode and logic LOW selects sleep mode, active only when ACOK is HIGH (input power not available). |
| 24 | EN | input | Charge control input; logic HIGH enables charging and logic LOW disables charging, active only when ACOK is low (input power OK). |
| 25 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Monolithic Power Systems |
| Package | QFN-24(4x4) |
| Category | Power Management |
| Pins | 25 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VCC UVLO | VCC UVLO | 2 | 2.2 | 2.4 | V | VIN = 5.0V, TA = 25°C | 4 |
| PWIN Lower Threshold | VPWIN L | 0.75 | 0.8 | 0.85 | V | | 4 |
| PWIN Upper Threshold | VPWIN H | 1.1 | 1.15 | 1.2 | V | | 4 |
| Input Current Limit | IIN_LIMIT | 400 | 450 | 500 | mA | RlLIM = 90.9k | 4 |
| Input Current Limit | IIN_LIMIT | 720 | 810 | 900 | mA | RlLIM = 49.9k | 4 |
| Input Current Limit | IIN_LIMIT | 2400 | 2700 | 3000 | mA | RlLIM = 15k | 4 |
| Terminal Battery Voltage | VBATT_FULL | 3.582 | 3.6 | 3.618 | V | Connect VB to GND | 4 |
| Terminal Battery Voltage | VBATT_FULL | 4.179 | 4.2 | 4.221 | V | Leave VB floating or connect to logic HIGH | 4 |
| Recharge Threshold | VRECH | 3.35 | 3.4 | 3.45 | V | Connect to VB to GND | 4 |
| Recharge Threshold | VRECH | 3.91 | 3.96 | 4.01 | V | Leave VB floating or connect to logic HIGH | 4 |
| Constant Charge Current | ICC | 900 | 1000 | 1100 | mA | RS1 = 40mΩ, RISET = 69.8k | 4 |
| Constant Charge Current | ICC | 1800 | 2000 | 2200 | mA | RS1 = 40mΩ, RISET = 34.9k | 4 |
| Trickle Charge Voltage Threshold | VBATT_TC | 2.47 | 2.57 | 2.67 | V | Connect to VB to GND | 5 |
| Trickle Charge Voltage Threshold | VBATT_TC | 2.9 | 3 | 3.1 | V | Leave VB floating or connect to high logic | 5 |
| Termination Charge Current | IBF | 5 | 10 | 15 | % ICC | | 5 |
| Input-Voltage-Regulation Reference | VREG | 1.18 | 1.2 | 1.22 | V | | 5 |
| Feedback Voltage | | 1.18 | 1.2 | 1.22 | V | Boost Mode | 5 |
| Boost SYS Over-Voltage Protection Threshold | VSYS(OVP) | 5.8 | 6 | 6.2 | V | Threshold over VSYS to turn off the converter during boost mode | 5 |
| Programmable Boost Output Current Limit Accuracy | IOLIM | 0.9 | 1 | 1.1 | A | RS1 = 40mΩ, ROLIM = 69.8k | 5 |
| Weak-Battery Threshold | VBATT(LOW) | 2.9 | | 3.05 | V | Before Boost starts | 5 |
| NTC Low Temp, Rising Threshold | | 65 | 66 | 67 | % VSYS | RNTC=NCP18XH103(0ºC) | 6 |
| NTC High Temp, Rising Threshold | | 34 | 35 | 36 | % VSYS | RNTC=NCP18XH103(50ºC) | 6 |
| Battery Leakage Current | ILEAKAGE | | 15 | 30 | μA | VBATT = 4.2V, SYS Float, VIN = 0V, MODE = 0V | 5 |
| Feedback Input Current | | | | 200 | nA | VFB=1V | 5 |
| ACOK, CHG, BOOST pin output low voltage | | | | 400 | mV | Sinking 1.5mA | 5 |
| ACOK, CHG, BOOST pin leakage current | | | | 1 | μA | Connected to 5V | 5 |
| EN Input Logic Low Voltage | | | | 0.4 | V | | 5 |
| EN Input High Voltage | | 1.4 | | | V | | 5 |
| Mode Input Logic Low Voltage | | | | 0.4 | V | | 5 |
| Mode Input Logic High Voltage | | 1.4 | | | V | | 5 |
| IN to SYS NMOS ON Resistance | RIN to SYS | | 100 | | mΩ | | 4 |
| High-side PMOS ON Resistance | RH DS | | 72 | | mΩ | | 4 |
| Low-side NMOS ON Resistance | RL DS | | 70 | | mΩ | | 4 |
| High-Side PMOS Peak Current Limit | IPEAK_HS | | 3.6 | | A | CC Charge Mode/ Boost Mode | 4 |
| High-Side PMOS Peak Current Limit | IPEAK_HS | | 1.5 | | A | TC Charge Mode | 4 |
| Low-Side NMOS Peak Current Limit | IPEAK_LS | | 2.8 | | A | | 4 |
| Switching Frequency | fsw | | 600 | | kHz | FREQ = 0 | 4 |
| Switching Frequency | fsw | | 1200 | | kHz | FREQ = Float/ High | 4 |
| Input Quiescent Current | IIN | | 2.5 | | mA | EN = 5V, Battery Float | 4 |
| Input Quiescent Current | IIN | | 1.5 | | mA | EN = 0 | 4 |
| Input Over-Current Threshold | IIN(OCP) | | 3 | | A | | 4 |
| Boost Quiescent Current | | | 1.4 | | mA | ISYS = 0, MODE = 5V | 5 |
| Thermal Shutdown Threshold | | | 150 | | °C | Guaranteed by design | 6 |
| Charging Current Foldback Threshold | | | 120 | | °C | Charge Mode; guaranteed by design | 6 |
| Input Voltage VIN (absolute max) | VIN | -0.3 | | 20 | V | | 3 |
| SYS, SW voltage | SYS, SW | -0.3 | | 6.5 | V | | 3 |
| BATT voltage | BATT | -0.3 | | 6.5 | V | | 3 |
| ACOK, CHG, BOOST voltage | | -0.3 | | 6.5 | V | | 3 |
| All Other Pins | | -0.3 | | 6.5 | V | | 3 |
| Junction Temperature | TJ | | | 150 | °C | | 3 |
| Lead Temperature | | | | 260 | °C | | 3 |
| Continuous Power Dissipation | PD | | | 2.97 | W | TA = +25°C | 3 |
| Operating Temperature | | -20 | | 85 | °C | | 3 |
| Supply Voltage VIN | VIN | 4.5 | | 6 | V | | 3 |
| Battery Voltage | VOUT | 2.5 | | 4.35 | V | | 3 |
| Operating Junction Temp. | TJ | -40 | | 125 | °C | | 3 |
| Thermal Resistance Junction-Ambient | θJA | | 42 | | °C/W | QFN24 (4×4mm), JESD51-7 4-layer PCB | 3 |
| Thermal Resistance Junction-Case | θJC | | 9 | | °C/W | QFN24 (4×4mm), JESD51-7 4-layer PCB | 3 |
## CAD (KiCad official)
- Symbol: `MP2635AGR-Z`
- Footprint: `Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm`
- 3D model: QFN-24(4x4) (KiCad packages3D, STEP)
- 3D model files: `mp2635agr-z-etched.step` / `mp2635agr-z-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `mp2635agr-z.step` / `mp2635agr-z.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Monolithic Power Systems datasheet](docs/mp2635agr-z-datasheet.pdf) (33 pp, sha256 `96ef7759a25b17bd`, retrieved 2026-10-23, tier: lcsc)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/mp2635agr-z-datasheet.pdf)