3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownMP2615BGQ-Z
Monolithic Power Systems · Battery Management ICs · QFN-16(3x3)
MP2615BGQ-Z from Monolithic Power Systems, in a QFN-16(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SW | power_out | Switch output node of the synchronous buck converter, connected to the inductor and the BST capacitor (absolute max -0.3V to 23V). |
| 2 | VIN | power_in | Power supply voltage input, 4.5V to 18V operating range (absolute max 23V). |
| 3 | VCC | power_out | Coarse regulator output, internally generated 4.5V, bypass with a 1µF capacitor to AGND; used as low-side driver supply and NTC divider bias, do not connect any external load. |
| 4 | CELL | input | Keep the pin floating or connect to GND. |
| 5 | SEL | input | Sets terminal battery voltage: Low or Float gives VBATT = 4.03V, High gives VBATT = 3.99V. |
| 6 | EN | input | On/Off control input, pulled down to GND by a 1Meg internal resistor (input low 0.4V max, input high 1.9V min). |
| 7 | N/C | unconnected | No connect, leave this pin floating. |
| 8 | AGND | power_in | Analog ground, connected to PGND at a single point. |
| 9 | BATT | passive | Positive battery terminal, connected to the battery side of the sense resistor RS1 (absolute max 12V). |
| 10 | CSP | input | Battery current sense positive input, connect sense resistor RS1 between CSP and BATT (absolute max 12V). |
| 11 | CHGOK | output | Open-drain charging completion indicator: logic low indicates charging, open drain once charge is completed or suspended (5mA sink current at 0.3V). |
| 12 | ACOK | output | Open-drain valid input supply indicator: logic low indicates a valid input power supply is present (5mA sink current at 0.3V). |
| 13 | NTC | input | Thermistor input, connect a resistor from this pin to VCC and the thermistor from this pin to ground. |
| 14 | TMR | passive | Internal safety timer control, connect a capacitor to AGND to set the timer; connecting directly to AGND disables the timer. |
| 15 | BST | passive | Bootstrap pin, capacitor connected between SW and BST forms the floating supply that drives the high-side power switch gate above the supply voltage. |
| 16 | PGND | power_in | Power ground. |
| 17 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Monolithic Power Systems |
| Package | QFN-16(3x3) |
| Category | Power Management |
| Pins | 17 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input Voltage | VIN | 4.5 | 12 | 18 | V | Cell Float | 3 |
| UVLO Threshold Rising | VUVLO | 3.55 | 3.75 | 3.95 | V | 3 | |
| Terminal Battery Voltage | VBATT_FULL | 4.01 | 4.03 | 4.05 | V | VSEL = 0V | 3 |
| Terminal Battery Voltage | VBATT_FULL | 3.91 | 3.93 | 3.95 | V | VSEL = 4V | 3 |
| Battery Over Voltage Threshold | VBOVP | 4.06 | 4.19 | 4.32 | V | VSEL = 0V | 3 |
| Battery Over Voltage Threshold | VBOVP | 3.96 | 4.09 | 4.22 | V | VSEL = 4V | 3 |
| Peak Current Limit CC | 3.2 | 4.2 | A | CC | 3 | ||
| CC Current | ICC | 1.8 | 2 | 2.2 | A | RS1 = 50mΩ | 3 |
| Trickle Charge Current | ITC | 5 | 10 | 15 | % ICC | 3 | |
| Termination Current Threshold | IBF | 5 | 10 | 15 | % ICC | 4 | |
| Maximum Current Sense Voltage (CSP to BATT) | VSENSE | 90 | 100 | 110 | mV | 4 | |
| VCC Output Voltage | VCC | 4.25 | 4.5 | 4.75 | V | 4 | |
| NTC Low Temp Rising Threshold | 70.5 | 73.3 | 74.6 | %VCC | RNTC=NCP18X103, 0°C | 4 | |
| NTC High Temp Falling Threshold | 28 | 29.3 | 30.6 | %VCC | RNTC=NCP18X103, 50°C | 4 | |
| Switch Leakage | 0 | 1 | μA | EN = 4V, VSW = 0V | 3 | ||
| CSP, BATT Current | ICSP, IBATT | 0.5 | µA | Charging disabled | 4 | ||
| Battery Reverse Leakage Current | ILEAKAGE | 0.5 | µA | 4 | |||
| VCC Load Regulation | ΔVCC | 10 | mV | ILOAD=0 to 10mA | 4 | ||
| EN Input Low Voltage | 0.4 | V | 4 | ||||
| EN Input High Voltage | 1.9 | V | 4 | ||||
| Absolute max VSW | VSW | -0.3 | 23 | V | 2 | ||
| Absolute max VIN, VACOK, VCHGOK | VIN | -0.3 | 23 | V | 2 | ||
| Absolute max VBATT, VCSP | VBATT | -0.3 | 12 | V | 2 | ||
| Absolute max All Other Pins | -0.3 | 6 | V | 2 | |||
| Absolute max VBST | VBST | 6 | V | VSW + 6V | 2 | ||
| Continuous Power Dissipation | PD | 2.5 | W | TA = +25°C | 2 | ||
| Operating Temperature | -40 | 85 | °C | 2 | |||
| Recommended Input Voltage | VIN | 4.5 | 18 | V | 2 | ||
| Recommended Battery Voltage | VBATT | 2 | 4.03 | V | 2 | ||
| Operating Junction Temp | TJ | -40 | 125 | °C | 2 | ||
| Thermal Resistance Junction-Ambient | θJA | 50 | °C/W | QFN-16 (3mmx3mm), JESD51-7 4-layer PCB | 2 | ||
| Thermal Resistance Junction-Case | θJC | 12 | °C/W | QFN-16 (3mmx3mm), JESD51-7 4-layer PCB | 2 | ||
| UVLO Hysteresis | 225 | mV | 3 | ||||
| High-side Switch On Resistance | RH_DS(ON) | 110 | mΩ | Measured from VIN to SW | 3 | ||
| Low-side Switch On Resistance | RL_DS(ON) | 110 | mΩ | 3 | |||
| Switching Frequency | FSW | 760 | kHz | VBATT = 3.8V | 3 | ||
| Thermal Shutdown | TSHDN | 150 | °C | 4 |
CAD (KiCad official)
- Symbol:
MP2615BGQ-Z - Footprint:
Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm - 3D model: QFN-16(3x3) (KiCad packages3D, STEP)
- 3D model files:
mp2615bgq-z-etched.step/mp2615bgq-z-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mp2615bgq-z.step/mp2615bgq-z.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Monolithic Power Systems datasheet (20 pp, sha256
b52fdcb2105fadf6, retrieved 2026-10-22, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).