main
Ray
Publish 0.1.0
4547ca6
MP2161AGJ-Z
Monolithic Power Systems · DC-DC Converters · TSOT-23-8
MP2161AGJ-Z from Monolithic Power Systems, in a TSOT-23-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | PG | output | Power good indicator, open drain with internal pull-up resistor to VIN (550kΩ); pulled up to VIN when FB is within ±10% of regulation, low otherwise. |
| 2 | VIN | power_in | Supply voltage input operating from +2.5V to +6V unregulated; C1 is needed to prevent large voltage spikes at the input. |
| 3 | SW | output | Switch output node connecting to the inductor. |
| 4 | PGND | power_in | Power ground. |
| 5 | OUT | input | Input sense for output voltage. |
| 6 | AGND | power_in | Analog ground for internal control circuit. |
| 7 | FB | input | Feedback input; an external resistor divider from the output to AGND, tapped to FB, sets the output voltage (0.6V reference). |
| 8 | EN | input | On/off control; enabled above 1.2V, disabled below 0.4V, floating or pulled low disables the device, with an internal 1MΩ resistor to ground. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Monolithic Power Systems |
| Package | TSOT-23-8 |
| Category | Power Management |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Feedback voltage | VFB | -1.5 | 1.5 | % | 2.5V ≤ VIN ≤ 6V, TA = 25°C | 4 | |
| Feedback voltage | VFB | -2 | 2 | % | TA = 0°C to +60°C | 4 | |
| Feedback voltage | VFB | -2.5 | 2.5 | % | TA = -40°C to +85°C | 4 | |
| Feedback voltage nominal | VFB | 0.6 | V | 2.5V ≤ VIN ≤ 6V, TA = 25°C | 4 | ||
| Feedback current | IFB | 10 | 50 | nA | VFB = 0.6V | 4 | |
| Switch leakage | 0 | 1 | μA | VEN = 0V, VIN = 6V, VSW = 0V and 6V | 4 | ||
| PFET current limit | 2.6 | 3.2 | 4 | A | 4 | ||
| Switching frequency tolerance | Fs | -20 | 20 | % | VOUT = 1.2V, TA = 25°C | 4 | |
| Switching frequency tolerance | Fs | -25 | 25 | % | TA = -40°C to +85°C | 4 | |
| Switching frequency | Fs | 1500 | kHz | VOUT = 1.2V, TA = 25°C | 4 | ||
| Soft-start time | TSS-ON | 0.6 | 1.15 | 1.7 | ms | VOUT from 10% to 90% | 4 |
| Power good sink voltage | VPG-L | 0.4 | V | Sink 1mA | 4 | ||
| Under-voltage lockout threshold rising | 2.15 | 2.3 | 2.45 | V | 4 | ||
| EN input logic-low voltage | 0.4 | V | 4 | ||||
| EN input logic-high voltage | 1.2 | V | 4 | ||||
| Supply current (shutdown) | 20 | 100 | nA | VEN = 0V, VIN = 3V | 4 | ||
| Supply current (quiescent) | 17 | 20 | μA | VEN = 2V, VFB = 0.63V, VIN = 5V | 4 | ||
| Supply voltage | VIN | 6.5 | V | 3 | |||
| All other pins | -0.3 | 6.5 | V | 3 | |||
| SW voltage | VSW | -0.3 | 6.5 | V | -1.5V for <20ns & -4V for <8ns; 10V for <10ns | 3 | |
| Junction temperature | TJ | 150 | °C | 3 | |||
| Lead temperature | 260 | °C | 3 | ||||
| Continuous power dissipation | PD | 1.25 | W | TA = +25°C | 3 | ||
| Storage temperature | -65 | 150 | °C | 3 | |||
| Supply voltage | VIN | 2.5 | 6 | V | 3 | ||
| Operating junction temperature | TJ | -40 | 125 | °C | 3 | ||
| Thermal resistance junction-ambient | θJA | 100 | °C/W | TSOT23-8, JESD51-7 4-layer PCB | 3 | ||
| Thermal resistance junction-case | θJC | 55 | °C/W | TSOT23-8, JESD51-7 4-layer PCB | 3 | ||
| PFET switch on resistance | RDSON_P | 110 | mΩ | 4 | |||
| NFET switch on resistance | RDSON_N | 60 | mΩ | 4 | |||
| On time | TON | 166 | ns | VIN = 5V, VOUT = 1.2V | 4 | ||
| On time | TON | 220 | ns | VIN = 3.6V, VOUT = 1.2V | 4 | ||
| Minimum off time | TMIN-OFF | 60 | ns | 4 | |||
| Power good upper trip threshold | PGH | 10 | % | FB voltage respect to the regulation | 4 | ||
| Power good lower trip threshold | PGL | -10 | % | 4 | |||
| Power good delay | PGD | 50 | μs | 4 | |||
| Power good logic-high voltage | VPG-H | 4.9 | V | VIN = 5V, VFB = 0.6V | 4 | ||
| Power good internal pull-up resistor | RPG | 550 | kΩ | 4 | |||
| Under-voltage lockout hysteresis | 260 | mV | 4 | ||||
| EN input current | 1.5 | μA | VEN = 2V | 4 | |||
| EN input current | 0 | μA | VEN = 0V | 4 | |||
| Thermal shutdown | 150 | °C | Guaranteed by design | 4 | |||
| Thermal hysteresis | 30 | °C | Guaranteed by design | 4 |
CAD (KiCad official)
- Symbol:
MP2161AGJ-Z - Footprint:
Package_TO_SOT_SMD:TSOT-23-8 - 3D model: TSOT-23-8 (KiCad packages3D, STEP)
- 3D model files:
mp2161agj-z-etched.step/mp2161agj-z-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mp2161agj-z.step/mp2161agj-z.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Monolithic Power Systems datasheet (15 pp, sha256
81f2980bc141d804, retrieved 2026-10-23, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# MP2161AGJ-Z
**Monolithic Power Systems** · DC-DC Converters · TSOT-23-8
MP2161AGJ-Z from Monolithic Power Systems, in a TSOT-23-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | PG | output | Power good indicator, open drain with internal pull-up resistor to VIN (550kΩ); pulled up to VIN when FB is within ±10% of regulation, low otherwise. |
| 2 | VIN | power_in | Supply voltage input operating from +2.5V to +6V unregulated; C1 is needed to prevent large voltage spikes at the input. |
| 3 | SW | output | Switch output node connecting to the inductor. |
| 4 | PGND | power_in | Power ground. |
| 5 | OUT | input | Input sense for output voltage. |
| 6 | AGND | power_in | Analog ground for internal control circuit. |
| 7 | FB | input | Feedback input; an external resistor divider from the output to AGND, tapped to FB, sets the output voltage (0.6V reference). |
| 8 | EN | input | On/off control; enabled above 1.2V, disabled below 0.4V, floating or pulled low disables the device, with an internal 1MΩ resistor to ground. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Monolithic Power Systems |
| Package | TSOT-23-8 |
| Category | Power Management |
| Pins | 8 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Feedback voltage | VFB | -1.5 | | 1.5 | % | 2.5V ≤ VIN ≤ 6V, TA = 25°C | 4 |
| Feedback voltage | VFB | -2 | | 2 | % | TA = 0°C to +60°C | 4 |
| Feedback voltage | VFB | -2.5 | | 2.5 | % | TA = -40°C to +85°C | 4 |
| Feedback voltage nominal | VFB | | 0.6 | | V | 2.5V ≤ VIN ≤ 6V, TA = 25°C | 4 |
| Feedback current | IFB | | 10 | 50 | nA | VFB = 0.6V | 4 |
| Switch leakage | | | 0 | 1 | μA | VEN = 0V, VIN = 6V, VSW = 0V and 6V | 4 |
| PFET current limit | | 2.6 | 3.2 | 4 | A | | 4 |
| Switching frequency tolerance | Fs | -20 | | 20 | % | VOUT = 1.2V, TA = 25°C | 4 |
| Switching frequency tolerance | Fs | -25 | | 25 | % | TA = -40°C to +85°C | 4 |
| Switching frequency | Fs | | 1500 | | kHz | VOUT = 1.2V, TA = 25°C | 4 |
| Soft-start time | TSS-ON | 0.6 | 1.15 | 1.7 | ms | VOUT from 10% to 90% | 4 |
| Power good sink voltage | VPG-L | | | 0.4 | V | Sink 1mA | 4 |
| Under-voltage lockout threshold rising | | 2.15 | 2.3 | 2.45 | V | | 4 |
| EN input logic-low voltage | | | | 0.4 | V | | 4 |
| EN input logic-high voltage | | 1.2 | | | V | | 4 |
| Supply current (shutdown) | | | 20 | 100 | nA | VEN = 0V, VIN = 3V | 4 |
| Supply current (quiescent) | | | 17 | 20 | μA | VEN = 2V, VFB = 0.63V, VIN = 5V | 4 |
| Supply voltage | VIN | | | 6.5 | V | | 3 |
| All other pins | | -0.3 | | 6.5 | V | | 3 |
| SW voltage | VSW | -0.3 | | 6.5 | V | -1.5V for <20ns & -4V for <8ns; 10V for <10ns | 3 |
| Junction temperature | TJ | | | 150 | °C | | 3 |
| Lead temperature | | | | 260 | °C | | 3 |
| Continuous power dissipation | PD | | | 1.25 | W | TA = +25°C | 3 |
| Storage temperature | | -65 | | 150 | °C | | 3 |
| Supply voltage | VIN | 2.5 | | 6 | V | | 3 |
| Operating junction temperature | TJ | -40 | | 125 | °C | | 3 |
| Thermal resistance junction-ambient | θJA | | 100 | | °C/W | TSOT23-8, JESD51-7 4-layer PCB | 3 |
| Thermal resistance junction-case | θJC | | 55 | | °C/W | TSOT23-8, JESD51-7 4-layer PCB | 3 |
| PFET switch on resistance | RDSON_P | | 110 | | mΩ | | 4 |
| NFET switch on resistance | RDSON_N | | 60 | | mΩ | | 4 |
| On time | TON | | 166 | | ns | VIN = 5V, VOUT = 1.2V | 4 |
| On time | TON | | 220 | | ns | VIN = 3.6V, VOUT = 1.2V | 4 |
| Minimum off time | TMIN-OFF | | 60 | | ns | | 4 |
| Power good upper trip threshold | PGH | | 10 | | % | FB voltage respect to the regulation | 4 |
| Power good lower trip threshold | PGL | | -10 | | % | | 4 |
| Power good delay | PGD | | 50 | | μs | | 4 |
| Power good logic-high voltage | VPG-H | | 4.9 | | V | VIN = 5V, VFB = 0.6V | 4 |
| Power good internal pull-up resistor | RPG | | 550 | | kΩ | | 4 |
| Under-voltage lockout hysteresis | | | 260 | | mV | | 4 |
| EN input current | | | 1.5 | | μA | VEN = 2V | 4 |
| EN input current | | | 0 | | μA | VEN = 0V | 4 |
| Thermal shutdown | | | 150 | | °C | Guaranteed by design | 4 |
| Thermal hysteresis | | | 30 | | °C | Guaranteed by design | 4 |
## CAD (KiCad official)
- Symbol: `MP2161AGJ-Z`
- Footprint: `Package_TO_SOT_SMD:TSOT-23-8`
- 3D model: TSOT-23-8 (KiCad packages3D, STEP)
- 3D model files: `mp2161agj-z-etched.step` / `mp2161agj-z-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `mp2161agj-z.step` / `mp2161agj-z.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Monolithic Power Systems datasheet](docs/mp2161agj-z-datasheet.pdf) (15 pp, sha256 `81f2980bc141d804`, retrieved 2026-10-23, tier: lcsc)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/mp2161agj-z-datasheet.pdf)