component
MP1495SGJ-Z
Public Made by Adomby adom
Monolithic Power Systems DC-DC Converters, TSOT-23-8. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
main
MP1495SGJ-Z
Monolithic Power Systems · DC-DC Converters · TSOT-23-8
MP1495SGJ-Z from Monolithic Power Systems, in a TSOT-23-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | AAM | input | Advanced Asynchronous Modulation pin: connect the tap of a resistor divider from VCC to set the AAM-to-CCM transition point, and drive it high (VCC) to force the part into CCM. |
| 2 | IN | power_in | Supply voltage input for a 4.5V to 16V input rail, decoupled by C1 and connected with a wide PCB trace. |
| 3 | SW | output | Switch output node, which must be connected with a wide PCB trace. |
| 4 | GND | power_in | System ground and reference for the regulated output voltage, to be connected to GND with copper traces and vias. |
| 5 | BST | passive | Bootstrap pin that requires a capacitor between SW and BST to form the floating high-side driver supply, with a 10Ω resistor between SW and the BST capacitor strongly recommended to reduce SW spike voltage. |
| 6 | EN/SYNC | input | Enable/synchronize pin: drive high to enable the regulator, and apply an external clock of 300kHz to 2MHz to change the switching frequency. |
| 7 | VCC | power_out | Internal 5V bias supply output that must be decoupled with a 0.1µF to 0.22µF capacitor placed close to the VCC and GND pins, not exceeding 0.22µF. |
| 8 | FB | input | Feedback input connected to the tap of an external resistor divider from the output to GND, with an internal 807mV feedback reference and frequency fold-back below 400mV. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Monolithic Power Systems |
| Package | TSOT-23-8 |
| Category | Power Management (PMIC) |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Current (Shutdown) | IIN | 1 | µA | VEN = 0V | 3 | ||
| Current Limit (under 40% duty cycle) | ILIMIT | 4.5 | 6 | A | Under 40% Duty Cycle | 3 | |
| Supply Current (Quiescent) | Iq | 0.5 | 1 | mA | VEN = 2V, VFB = 1V, AAM=0.5V | 3 | |
| HS Switch-ON Resistance | HSRDS-ON | 120 | mΩ | VBST-SW=5V | 3 | ||
| LS Switch-ON Resistance | LSRDS-ON | 50 | mΩ | VCC =5V | 3 | ||
| Switch Leakage | SWLKG | 1 | µA | VEN = 0V, VSW = 12V | 3 | ||
| Oscillator Frequency | fSW | 410 | 500 | 580 | kHz | VFB=0.75V | 3 |
| Fold-Back Frequency | fFB | 0.5 | fSW | VFB=200mV | 3 | ||
| Maximum Duty Cycle | DMAX | 90 | 95 | % | VFB=700mV | 3 | |
| Minimum ON Time | tON_MIN | 60 | ns | 3 | |||
| Sync Frequency Range | fSYNC | 0.3 | 2 | MHz | 3 | ||
| Feedback Voltage | VFB | 791 | 807 | 823 | mV | TA = 25°C | 3 |
| Feedback Voltage | VFB | 787 | 807 | 827 | mV | -40°C < TA < 85°C (not tested in production; guaranteed by over-temperature correlation) | 3 |
| Feedback Current | IFB | 30 | 65 | nA | VFB=820mV | 3 | |
| EN Rising Threshold | VEN_RISING | 1.15 | 1.35 | 1.55 | V | 3 | |
| EN Falling Threshold | VEN_FALLING | 1.05 | 1.2 | 1.35 | V | 3 | |
| EN Input Current | IEN | 2 | µA | VEN = 2V | 3 | ||
| EN Input Current | IEN | 0 | µA | VEN = 0 | 3 | ||
| EN Turn-Off Delay | ENtd-off | 8 | µs | 3 | |||
| VIN Under-Voltage Lockout Threshold-Rising | INUVVth | 3.5 | 3.8 | 4.1 | V | 3 | |
| VIN Under-Voltage Lockout Threshold-Hysteresis | INUVHYS | 650 | mV | 3 | |||
| VCC Regulator | VCC | 5 | V | 3 | |||
| VCC Load Regulation | 3 | % | ICC=5mA | 3 | |||
| Soft-Start Period | tSS | 1.5 | ms | 3 | |||
| Thermal Shutdown | 150 | °C | 3 | ||||
| Thermal Hysteresis | 20 | °C | 3 | ||||
| VIN voltage (absolute maximum) | VIN | -0.3 | 17 | V | 2 | ||
| VSW voltage (absolute maximum, continuous) | VSW | -0.3 | 17 | V | 2 | ||
| VSW voltage (absolute maximum, transient) | VSW | -5 | 19 | V | <10ns | 2 | |
| All other pins voltage (absolute maximum) | -0.3 | 6 | V | 2 | |||
| Junction Temperature | TJ | 150 | °C | 2 | |||
| Storage Temperature | TSTG | -65 | 150 | °C | 2 | ||
| Supply Voltage VIN (recommended) | VIN | 4.5 | 16 | V | 2 | ||
| Output Voltage VOUT (recommended) | VOUT | 0.8 | V | Upper limit printed as VINxDMAX | 2 | ||
| Operating Junction Temperature (recommended) | TJ | -40 | 125 | °C | 2 | ||
| Junction-to-Ambient Thermal Resistance (TSOT-23-8) | θJA | 100 | °C/W | JESD51-7, 4-layer PCB | 2 | ||
| Junction-to-Case Thermal Resistance (TSOT-23-8) | θJC | 55 | °C/W | JESD51-7, 4-layer PCB | 2 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | System Ground. This pin is the reference ground of the regulated output voltage, and PCB layout requires special care. For best results, connect to GND with copper traces | 8 |
CAD (KiCad official)
- Symbol:
MP1495SGJ-Z - Footprint:
Package_TO_SOT_SMD:TSOT-23-8 - 3D model: TSOT-23-8 (KiCad packages3D, STEP)
- 3D model files:
mp1495sgj-z-etched.step/mp1495sgj-z-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mp1495sgj-z.step/mp1495sgj-z.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Monolithic Power Systems datasheet (17 pp, sha256
7ff59be5b0dc10fa, retrieved 2026-10-19, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# MP1495SGJ-Z
**Monolithic Power Systems** · DC-DC Converters · TSOT-23-8
MP1495SGJ-Z from Monolithic Power Systems, in a TSOT-23-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | AAM | input | Advanced Asynchronous Modulation pin: connect the tap of a resistor divider from VCC to set the AAM-to-CCM transition point, and drive it high (VCC) to force the part into CCM. |
| 2 | IN | power_in | Supply voltage input for a 4.5V to 16V input rail, decoupled by C1 and connected with a wide PCB trace. |
| 3 | SW | output | Switch output node, which must be connected with a wide PCB trace. |
| 4 | GND | power_in | System ground and reference for the regulated output voltage, to be connected to GND with copper traces and vias. |
| 5 | BST | passive | Bootstrap pin that requires a capacitor between SW and BST to form the floating high-side driver supply, with a 10Ω resistor between SW and the BST capacitor strongly recommended to reduce SW spike voltage. |
| 6 | EN/SYNC | input | Enable/synchronize pin: drive high to enable the regulator, and apply an external clock of 300kHz to 2MHz to change the switching frequency. |
| 7 | VCC | power_out | Internal 5V bias supply output that must be decoupled with a 0.1µF to 0.22µF capacitor placed close to the VCC and GND pins, not exceeding 0.22µF. |
| 8 | FB | input | Feedback input connected to the tap of an external resistor divider from the output to GND, with an internal 807mV feedback reference and frequency fold-back below 400mV. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Monolithic Power Systems |
| Package | TSOT-23-8 |
| Category | Power Management (PMIC) |
| Pins | 8 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Current (Shutdown) | IIN | | | 1 | µA | VEN = 0V | 3 |
| Current Limit (under 40% duty cycle) | ILIMIT | 4.5 | | 6 | A | Under 40% Duty Cycle | 3 |
| Supply Current (Quiescent) | Iq | | 0.5 | 1 | mA | VEN = 2V, VFB = 1V, AAM=0.5V | 3 |
| HS Switch-ON Resistance | HSRDS-ON | | 120 | | mΩ | VBST-SW=5V | 3 |
| LS Switch-ON Resistance | LSRDS-ON | | 50 | | mΩ | VCC =5V | 3 |
| Switch Leakage | SWLKG | | | 1 | µA | VEN = 0V, VSW = 12V | 3 |
| Oscillator Frequency | fSW | 410 | 500 | 580 | kHz | VFB=0.75V | 3 |
| Fold-Back Frequency | fFB | 0.5 | | | fSW | VFB=200mV | 3 |
| Maximum Duty Cycle | DMAX | 90 | | 95 | % | VFB=700mV | 3 |
| Minimum ON Time | tON_MIN | | 60 | | ns | | 3 |
| Sync Frequency Range | fSYNC | 0.3 | | 2 | MHz | | 3 |
| Feedback Voltage | VFB | 791 | 807 | 823 | mV | TA = 25°C | 3 |
| Feedback Voltage | VFB | 787 | 807 | 827 | mV | -40°C < TA < 85°C (not tested in production; guaranteed by over-temperature correlation) | 3 |
| Feedback Current | IFB | | 30 | 65 | nA | VFB=820mV | 3 |
| EN Rising Threshold | VEN_RISING | 1.15 | 1.35 | 1.55 | V | | 3 |
| EN Falling Threshold | VEN_FALLING | 1.05 | 1.2 | 1.35 | V | | 3 |
| EN Input Current | IEN | | | 2 | µA | VEN = 2V | 3 |
| EN Input Current | IEN | | | 0 | µA | VEN = 0 | 3 |
| EN Turn-Off Delay | ENtd-off | | 8 | | µs | | 3 |
| VIN Under-Voltage Lockout Threshold-Rising | INUVVth | 3.5 | 3.8 | 4.1 | V | | 3 |
| VIN Under-Voltage Lockout Threshold-Hysteresis | INUVHYS | | 650 | | mV | | 3 |
| VCC Regulator | VCC | | 5 | | V | | 3 |
| VCC Load Regulation | | | 3 | | % | ICC=5mA | 3 |
| Soft-Start Period | tSS | | 1.5 | | ms | | 3 |
| Thermal Shutdown | | | 150 | | °C | | 3 |
| Thermal Hysteresis | | | 20 | | °C | | 3 |
| VIN voltage (absolute maximum) | VIN | -0.3 | | 17 | V | | 2 |
| VSW voltage (absolute maximum, continuous) | VSW | -0.3 | | 17 | V | | 2 |
| VSW voltage (absolute maximum, transient) | VSW | -5 | | 19 | V | <10ns | 2 |
| All other pins voltage (absolute maximum) | | -0.3 | | 6 | V | | 2 |
| Junction Temperature | TJ | | | 150 | °C | | 2 |
| Storage Temperature | TSTG | -65 | | 150 | °C | | 2 |
| Supply Voltage VIN (recommended) | VIN | 4.5 | | 16 | V | | 2 |
| Output Voltage VOUT (recommended) | VOUT | 0.8 | | | V | Upper limit printed as VINxDMAX | 2 |
| Operating Junction Temperature (recommended) | TJ | -40 | | 125 | °C | | 2 |
| Junction-to-Ambient Thermal Resistance (TSOT-23-8) | θJA | | 100 | | °C/W | JESD51-7, 4-layer PCB | 2 |
| Junction-to-Case Thermal Resistance (TSOT-23-8) | θJC | | 55 | | °C/W | JESD51-7, 4-layer PCB | 2 |
## Materials and finish
As the datasheet states them (page.json `metadata.appearance`; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | | System Ground. This pin is the reference ground of the regulated output voltage, and PCB layout requires special care. For best results, connect to GND with copper traces | 8 |
## CAD (KiCad official)
- Symbol: `MP1495SGJ-Z`
- Footprint: `Package_TO_SOT_SMD:TSOT-23-8`
- 3D model: TSOT-23-8 (KiCad packages3D, STEP)
- 3D model files: `mp1495sgj-z-etched.step` / `mp1495sgj-z-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `mp1495sgj-z.step` / `mp1495sgj-z.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Monolithic Power Systems datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8590905893800800256) (17 pp, sha256 `7ff59be5b0dc10fa`, retrieved 2026-10-19, tier: lcsc)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/mp1495sgj-z-datasheet.pdf)