Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

MLX91218LDC-ARX-500-SP

Melexis · Current Sensors · SOIC-8

MLX91218LDC-ARX-500-SP from Melexis, in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VREF power_in Reference voltage output (nominal 0.5 V to 2.5 V depending on version); the resistance on this pin must be large, normally above 200 kΩ, because the maximum source current is 0.6 mA (typical).
2 OUT output Analog measurement output, ratiometric or fixed (VREF) depending on option code, with linear swing of 10 % to 90 % VDD into a pull-down or pull-up of 10 kΩ or more.
3 GND power_in Ground reference for the supply and sensor; the absolute maximum reverse pin voltage is GND - 0.3 V.
4 VDD power_in Supply voltage; for the 5xx option the nominal range is 4.5 V to 5.5 V (5 V typical) and the overvoltage limit is +8 V.
5 NC unconnected Not connected; for optimal EMC results the unused NC pin is recommended to be connected to ground.
6 OCD_EXT output Overcurrent detection output based on the external threshold set at VOC_EXT; it is pulled to ground when an overcurrent is detected, with a 10 µs output dwell time, and it stays at VDD during normal operation.
7 OCD_INT output Overcurrent detection output based on the internal EEPROM threshold; it is pulled to ground on detection, with an output dwell time of 7 µs to 14 µs, and stays at VDD during normal operation.
8 VOC_EXT input Input that sets the external OCD threshold voltage through a voltage divider; the allowed range is 0.5 V to 4.5 V at VDD = 5 V for the 5xx versions.

Key specifications

Parameter Value
Manufacturer Melexis
Package SOIC-8
Category Sensors
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Positive Supply Voltage (overvoltage) VDD 8 V 9
Negative Supply Voltage VDD -0.3 V 9
Output Sink Current Iout_max 50 mA 9
Output Source Current Iout_source 25 mA 9
Output Short Circuit Current to GND ISHORT_GND -100 mA 9
Output Short Circuit Current to VDD ISHORT_VDD 60 mA 9
Maximum Junction Temperature Tj_MAX 165 °C 9
Operating Ambient Temperature Range TA -40 150 °C 9
Storage Temperature Range TS -55 165 °C 9
Magnetic Flux Density BMAX -3 3 T 9
Human Body ESD Protection ESDHBM 2 kV HBM 9
Charged Device Model ESD Protection, all pins ESDCDM 500 V All pins 9
Charged Device Model ESD Protection, corner pins ESDCDM 750 V Corner pins 9
Nominal Supply Voltage VDD 4.5 5 5.5 V MLX91218LDC-Axx-5xx 10
Positive Supply Voltage (maintaining application mode) VDD 6.5 V Maintaining application mode 10
Supply Current IDD 15.5 19 mA Without RLOAD on output, in application mode, VDD=5V 10
Output Resistance ROUT 1 5 Ω VOUT = 50%VDD, ILOAD = 10mA 10
Voltage Reference Output Resistance RREF 120 200 333 Ω VREF=2.5V: ISINK=5mA; ISOURCE=0.2mA 10
Output Capacitive Load CLOAD 0 4.7 6 nF Output amplifier stability optimized for this typical value 10
Output Leakage Current ILEAK 6 20 µA High impedance mode, TA=150°C 10
Output Voltage Linear Swing VOUT_LSW 10 90 %VDD Pull-down or pull-up ≥ 10 kΩ; VDD > 4.6 V for Fixed Mode versions 10
Operational Magnetic Field Range (Extra High Field) BOP -100 100 mT Option code AxX 11
Linearity Error (Magnetic) NL -0.5 0.5 %FS B within BOP, TA = 25°C 11
Hysteresis, Remanent Field BR -90 90 µT Measured after B = BOP 11
Sensitivity accuracy (factory trimming) SACC -1 1 %S TA = 25°C 11
Sensitivity Programming Resolution SRES 0.5 %S B = BOP 11
Voltage Output Quiescent VOQ -5 5 mV No magnetic field applied, TA=25°C 14
Ratiometric Offset Error ΔRVOQ 1.6 mV/%VDD VDD = 5V 14
Non-Ratiometric Offset Error ΔRVOQ 5 mV VDD = 5V 14
Thermal Offset Drift ΔTVOQ -5 5 mV TA = -40 to 125°C 14
Thermal Offset Drift ΔTVOQ -6 6 mV TA = -40 to 150°C 14
Total Offset Drift ΔVOQ -6 6 mV TA = -40 to 125°C 14
Total Offset Drift ΔVOQ -8 8 mV TA = -40 to 150°C 14
Ratiometric Sensitivity Error ΔRS 0.16 %S/%VDD 14
Non-Ratiometric Sensitivity Error ΔRS -0.6 0.6 %S 14
Thermal Sensitivity Drift ΔTS -1.5 1 1.5 %S TA = -40 to 125°C 14
Thermal Sensitivity Drift ΔTS -2.2 2.2 %S TA = -40 to 150°C 14
Total Sensitivity Drift ΔS -1.5 1.5 %S 14
Input referred noise spectral density NPSD 175 nT/√Hz Within BW = 1..400kHz, max gain, option code AxX 14
Step Response Time TRESP 2 µs Delay 90% input to 90% output; SF=1 (default) 15
Step Response Time TRESP 3.5 µs Delay 90% input to 90% output; SF=2 15
Step Response Time TRESP 6 µs Delay 90% input to 90% output; SF=3 15
Bandwidth BW 400 kHz -3dB, TA = 25°C, SF=1 (default) 15
Bandwidth BW 200 kHz -3dB, TA = 25°C, SF=2 15
Bandwidth BW 100 kHz -3dB, TA = 25°C, SF=3 15
Power on Delay TPOD 1 ms VREF capacitor = 47nF 15
OCD_INT Internal ON Resistance RON_OCD_INT 60 90 150 Ω ISINK = 1 mA 17
OCD_EXT Internal ON Resistance RON_OCD_EXT 160 190 280 Ω ISINK = 1 mA 17
VOC_EXT Voltage Range (bidirectional) VOC_EXT_5V 0.5 2 V VDD=5V, 5xx versions, RS=0, bidirectional 17
VOC_EXT Voltage Range (unidirectional) VOC_EXT_5V 0.9 4.5 V VDD=5V, 5xx versions, RS=3, unidirectional 17
OCDINT accuracy OCDINT -10 10 %Thr Ratiometric output 17
OCDEXT accuracy OCDEXT -1.5 1.5 %FS 17
OCDINT response time 1.4 µs TDT=0 17
OCDINT response time 2.1 µs TDT=1 17
OCDEXT response time 10 µs 17
OCDINT required input holding time 1 µs 17
OCDEXT required input holding time 10 µs 17
OCDINT output dwell time 7 14 µs 17
OCDEXT output dwell time 10 µs 17

CAD (KiCad official)

  • Symbol: MLX91218LDC-ARX-500-SP
  • Footprint: Package_SO:SOIC-8_3.9x4.9mm_P1.27mm
  • 3D model: SOIC-8 (KiCad packages3D, STEP)
  • 3D model files: mlx91218ldc-arx-500-sp-etched.step / mlx91218ldc-arx-500-sp-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); mlx91218ldc-arx-500-sp.step / mlx91218ldc-arx-500-sp.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Melexis datasheet (28 pp, sha256 8c447f793574dff0, retrieved 2026-11-17, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF