Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

MICRF221AYQS-TR

Microchip Tech · RF Transceiver ICs · QSOP-16-150mil

MICRF221AYQS-TR from Microchip Tech, in a QSOP-16-150mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 RO1 input Reference oscillator input to the pierce oscillator stage, can be driven by an external reference of 1.5V p-p maximum, with 7pF to GND in normal operation.
2 GNDRF power_in Negative supply connection associated with the ANT RF input.
3 ANT input Antenna RF signal input, internally AC coupled; a matching network with an inductor to RF ground is recommended to improve ESD protection.
4 GNDRF power_in Negative supply connection associated with the ANT RF input.
5 VDD power_in Positive supply connection for all chip functions, operating range 3.0V to 3.6V.
6 SQ input Squelch control logic input with active internal pull-up (3uA typical); not recommended for the MICRF221 and should be left floating.
7 SEL0 input Select logic input with 3μA (8μA max) internal pull-up when not in shutdown or SLEEP, used with SEL1 to set the D3 bandwidth LSB.
8 SHDN input Shutdown logic control input with active internal pull-up.
9 GND power_in Negative supply connection for all chip functions except the RF input.
10 DO bidirectional Demodulated data CMOS current-limited output that also serves as the Schmitt input for serial interface data, with a 25kΩ pull-down in shutdown and sleep modes.
11 SEL1 input Select logic input with 3μA (8μA max) internal pull-up when not in shutdown or SLEEP, used with SEL0 to set the D4 bandwidth MSB.
12 CTH passive Demodulation threshold integration capacitor to GND setting the data slicing level settling time, values above 1nF recommended.
13 CAGC passive AGC filter capacitor connection to GND, normally greater than 0.47μF.
14 RSSI output Received signal strength indication output from a switched capacitor integrating op amp with 220Ω typical output impedance.
15 SCLK input Serial interface clock CMOS Schmitt input, with a 25kΩ pull-down present in shutdown mode.
16 RO2 passive Reference resonator connection, with 7pF to GND during normal operation.

Key specifications

Parameter Value
Manufacturer Microchip Tech
Package QSOP-16-150mil
Category RF & Radio
Pins 16

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply Voltage VDD 3 3.6 V Operating Ratings 3
Ambient Temperature TA -40 105 °C Operating Ratings 3
Input Voltage Vin 3.6 V Operating Ratings 3
Maximum Input RF Power -20 dBm Operating Ratings 3
Receive Modulation Duty Cycle 20 80 % Operating Ratings, Note 6 3
Supply Voltage VDD 5 V 3
Input Voltage 5 V 3
Junction Temperature 150 °C 3
Storage Temperature Ts -65 150 °C 3
Maximum Receiver Input Power 10 dBm 3
ESD Rating 2 kV HBM 3
Tsleep Programming Range Tsleep 10 1300 ms 4
Demodulator Filter Bandwidth 1712 13000 Hz @ 915MHz, Programmable 4
Input High Voltage 0.8 V Pins SCLK, DO (as input), SHDN; printed as 0.8Vdd 4
Input Low Voltage 0.2 V Pins SCLK, DO (as input), SHDN; printed as 0.2Vdd 4
Output Voltage High 0.8 V DO; printed as 0.8Vdd 4
Output Voltage Low 0.2 V DO; printed as 0.2Vdd 4
Operating Supply Current Iss 9 mA Continuous Operation, fRX = 868MHz 3
Operating Supply Current Iss 9.5 mA Continuous Operation, fRX = 915MHz 3
Shutdown Current Ishut 50 nA 3
Image Rejection 20 dB 3
Receiver Sensitivity @ 1kbps -109 dBm fRX = 915MHz (matched to 50Ω) 3
SLEEP Current Isleep 15 µA 2ms on, 1.3s off 4
Reference Oscillator Frequency 14.2764 MHz fRX = 915MHz 4
Output Rise and Fall Times 2 µs CI = 15 pF, pin DO, 10-90% 4
RSSI Response Slope 26 mV/dB -109dBm to -40dBm 5
RSSI Output Impedance 220 Ω 5

CAD (KiCad official)

  • Symbol: MICRF221AYQS-TR
  • Footprint: Package_SO:QSOP-16_3.9x4.9mm_P0.635mm
  • 3D model: QSOP-16-150mil (KiCad packages3D, STEP)
  • 3D model files: micrf221ayqs-tr-etched.step / micrf221ayqs-tr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); micrf221ayqs-tr.step / micrf221ayqs-tr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Microchip Tech datasheet (26 pp, sha256 8e57f6b5a850cae8, retrieved 2026-10-27, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF