Generated by kicad-footprint-generator · KiCad file format 20260206
MIC4600YML-TR
Microchip Tech · Gate Drive ICs · VQFN-16-EP(3x3)
MIC4600YML-TR from Microchip Tech, in a VQFN-16-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VIN | power_in | VIN is the input supply to the internal LDO, with an operating range of 4.5V to 28V, and needs a decoupling capacitor to PGND. |
| 2 | EN | input | EN is the enable input, where logic high allows normal operation and logic low shuts down the drive in a low quiescent current state, and it must not be left floating. |
| 3 | HSI | input | HSI is the logic-level high-side input that controls the high-side gate drive. |
| 4 | LSI | input | LSI is the logic-level low-side input that controls the low-side gate drive. |
| 5 | NC | unconnected | NC is a no-connect pin that is not internally connected. |
| 6 | FAULT | output | FAULT is an active-low open-drain output that pulls low during an overtemperature fault and requires a resistor to VDD to pull it high. |
| 7 | DELAY | output | DELAY is the pin where a resistor to ground sets the dead time (break-before-make) between the high- and low-side MOSFETs. |
| 8 | AGND | power_in | AGND is the analog ground that must be connected directly to the ground planes and not routed to the PGND pad on the top layer. |
| 9 | PGND | power_in | PGND is the ground path for the output drivers and should connect to the low-side MOSFET source and the negative terminals of the decoupling capacitors. |
| 10 | DL | output | DL is the drive low output that drives the low-side MOSFET gate. |
| 11 | SW | output | SW is the switch node connecting the high-side MOSFET source and low-side MOSFET drain, and should be routed away from sensitive nodes due to high-speed switching. |
| 12 | DH | output | DH is the drive high output that drives the high-side MOSFET gate. |
| 13 | BST | output | BST is the bootstrapped supply for the high-side driver, requiring a Schottky diode from VDD and a boost capacitor to SW. |
| 14 | VDD | power_out | VDD is the 5V internal linear regulator output that supplies the gate drive, must be tied to VIN when VIN is below 5.5V, and requires a 2.2 µF ceramic capacitor to ground for stability. |
| 15 | AVDD | input | AVDD is the 5V analog supply for the internal driver logic and control circuitry and must be connected to the VDD output. |
| 16 | AGND | power_in | AGND is the second analog ground pin that must be connected directly to the ground planes and not routed to the PGND pad on the top layer. |
| 17 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | VQFN-16-EP(3x3) |
| Category | Power Supply Chip |
| Pins | 17 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input Voltage Range | VIN | 4.5 | 28 | V | 3 | ||
| VDD Output Voltage | VDD | 4.8 | 5 | 5.4 | V | VIN = 7V to 26V, IDD = 25 mA | 3 |
| VDD UVLO Threshold | 3.6 | 4 | 4.4 | V | VDD Rising | 3 | |
| EN Logic Threshold | 0.65 | 1.25 | 1.4 | V | Rising | 3 | |
| Quiescent Supply Current | IQ | 450 | 750 | µA | HSI = VDD, LSI = 0V, RDELAY = 124 kΩ, non-switching | 3 | |
| Shutdown Supply Current | 9 | 20 | µA | VEN = 0V | 3 | ||
| Maximum Junction Temperature | TJ | 150 | °C | 5 | |||
| Lead Temperature | 260 | °C | Soldering, 10 sec. | 5 | |||
| Junction Operating Temperature | TJ | -40 | 125 | °C | 5 | ||
| Storage Temperature Range | -65 | 150 | °C | 5 | |||
| HSI Logic Level High | 1.4 | V | 4 | ||||
| HSI Logic Level Low | 0.65 | V | 4 | ||||
| LSI Logic Level High | 1.4 | V | 4 | ||||
| LSI Logic Level Low | 0.65 | V | 4 | ||||
| Switching Frequency Range | 1.5 | MHz | 4 | ||||
| EN Input Bias Current | 2 | µA | VEN = 12V | 4 | |||
| FAULT Logic Level Low | 0.125 | 0.2 | V | VIFAULT = 5 mA | 4 | ||
| FAULT Pin Leakage Current | 0.01 | 0.1 | µA | VFAULT = 5.5V | 4 | ||
| HSI Bias Current | 0.01 | 0.1 | µA | VHSI = 5V | 4 | ||
| LSI Bias Current | 0.01 | 0.1 | µA | VLSI = 5V | 4 | ||
| DH RDS(ON), High | RDS(ON) | 2 | 3 | Ω | IDH = 20 mA | 4 | |
| DH RDS(ON), Low | RDS(ON) | 1.5 | 3 | Ω | IDH = -20 mA | 4 | |
| DL RDS(ON), High | RDS(ON) | 2 | 3 | Ω | IDL = 20 mA | 4 | |
| DL RDS(ON), Low | RDS(ON) | 1 | 2 | Ω | IDL = -20 mA | 4 | |
| Thermal Resistance, 3x3 QFN-16Ld | θJA | 59 | °C/W | 5 | |||
| VDD UVLO Hysteresis | 400 | mV | 3 | ||||
| Dropout Voltage (VIN, VDD) | 380 | mV | IDD = 25 mA, VIN= 5V | 3 | |||
| VDD Load Regulation | 1.23 | % | IDD = 0 mA to 25 mA | 3 | |||
| EN Hysteresis | 200 | mV | 3 | ||||
| Fault Overtemperature | 150 | °C | TJ rising | 4 | |||
| Overtemperature Hysteresis | 23 | °C | 4 | ||||
| Dead Time | 18.7 | ns | RDELAY = 105 kΩ | 4 | |||
| Minimum Allowable Pulse Width | tPW | 32 | ns | 4 | |||
| Rise Time (DH, DL) | tr | 15 | ns | CLOAD = 3 nF, 10%VDD to 90%VDD | 4 | ||
| Fall Time (DH,DL) | tf | 13.5 | ns | CLOAD = 3 nF, 10%VDD to 90%VDD | 4 | ||
| Propagation Delay, Rising HSI to DH | tHPLH | 26 | ns | GND to 10%xVDD | 4 | ||
| Propagation Delay, Rising LSI to DL | tLPLH | 18 | ns | GND to 10%xVDD | 4 | ||
| Propagation Delay, Falling HSI to DH | tHPHL | 55 | ns | VDD to 90%xVDD | 4 | ||
| Propagation Delay, Falling LSI to DL | tLPHL | 14 | ns | VDD to 90%xVDD | 4 | ||
| VIN to PGND | VIN | -0.3 | 29 | V | 3 | ||
| VDD to PGND | VDD | -0.3 | 6 | V | 3 | ||
| VSW to PGND | VSW | -0.3 | V | Upper limit printed as VIN + 0.3V | 3 | ||
| VBST to VSW | VBST | -0.3 | 6 | V | 3 | ||
| VBST to PGND | VBST | -0.3 | 34 | V | 3 | ||
| VHSI, VLSI to PGND | VHSI, VLSI | -0.3 | V | Upper limit printed as VDD + 0.3V | 3 | ||
| VFAULT to AGND | VFAULT | -0.3 | 6 | V | 3 | ||
| VEN to PGND | VEN | -0.3 | V | Upper limit printed as VIN + 0.3V | 3 | ||
| PGND to AGND | -0.3 | 0.3 | V | 3 | |||
| ESD Protection on All Pins | -1.5 | 1.5 | kV | HBM | 3 | ||
| VDD Supply Voltage | VDD | 4.5 | 5.5 | V | 3 | ||
| Enable Input | VEN | 0 | V | Upper limit printed as VIN | 3 |
CAD (KiCad official)
- Symbol:
MIC4600YML-TR - Footprint:
Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm - 3D model: VQFN-16-EP(3x3) (KiCad packages3D, STEP)
- 3D model files:
mic4600yml-tr-etched.step/mic4600yml-tr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mic4600yml-tr.step/mic4600yml-tr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (26 pp, sha256
da17d34f4579a80e, retrieved 2026-11-02, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).