main
Download ZIP Propose a change
Generated by kicad-footprint-generator · KiCad file format 20260206
Name Last commit message Last updated
docs Publish 0.1.0 · Ray
viewers mic3808ym: viewers · Ray
mic3808ym-etched.glb mic3808ym: factory component page (tier=lcsc) · Ray
mic3808ym-etched.step mic3808ym: factory component page (tier=lcsc) · Ray
mic3808ym-hero.glb mic3808ym: hero GLB from the etched model (keeps the MPN mark) · Ray
mic3808ym-hero.overlay.json mic3808ym: hero GLB from the etched model (keeps the MPN mark) · Ray
mic3808ym.glb Publish 0.1.0 · Ray
mic3808ym.kicad_mod Publish 0.1.0 · Ray
mic3808ym.kicad_sym Publish 0.1.0 · Ray
mic3808ym.lbr Publish 0.1.0 · Ray
mic3808ym.step Publish 0.1.0 · Ray
package.json Publish 0.1.1 · Ray
page.json Publish 0.1.1 · Ray
README.md mic3808ym: the pins were read twice by one model (sonnet); say so instead of 'cross-checked by two models' · Ray
verification.json Verified: Published by the parts factory: tier lcsc, 8 pins · Ray

MIC3808YM

Microchip Tech · DC-DC Controllers · SOIC-8

MIC3808YM from Microchip Tech, in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, read twice and the reads agreed). Symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 COMP output Error amplifier output and PWM comparator input; can source and sink current, is internally current limited and clamped to 3.65V typ, and pulling it to GND forces zero duty cycle (soft start is a clamp on the maximum COMP voltage).
2 FB input Inverting input to the error amplifier; keep lead length and stray capacitance as small as possible for best stability.
3 CS input Current-sense input to the PWM, peak current and overcurrent comparators; exceeding the 0.75V typ overcurrent threshold triggers a soft start cycle, and an internal MOSFET discharges the sense filter capacitor.
4 RC passive Oscillator programming pin with a resistor to VDD and a capacitor to GND, F = 1.41/(R×C), with recommended 100pF to 1000pF timing capacitor range and timing resistors of 7kΩ to 200kΩ.
5 GND power_in Ground.
6 OUTB output Alternating high-current push-pull gate-drive output capable of 500mA peak source and 1A peak sink current, switching at half the oscillator frequency with 60ns to 200ns dead time versus OUTA.
7 OUTA output Alternating high-current push-pull gate-drive output capable of 500mA peak source and 1A peak sink current, switching at half the oscillator frequency with 60ns to 200ns dead time versus OUTB.
8 VDD power_in Power input, internally clamped (zener shunt 13V min, 14V typ, 15V max) with 20mA maximum supply current; bypass to GND with a ceramic capacitor, 1µF recommended, placed close to the chip.

Key specifications

Parameter Value
Manufacturer Microchip Tech
Package SOIC-8
Category Power Supply Chip
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Oscillator Frequency fOSC 180 200 220 kHz TA=TJ=-40 to +85°C, VDD=10V, R=22kΩ, C=330pF 4
Oscillator Amplitude/VDD 0.44 0.5 0.56 V/V Note 4 4
Error Amp Input Voltage 1.95 2 2.05 V COMP = 2V 4
Error Amp Input Bias Current -1 1 µA 4
Open Loop Voltage Gain 60 80 dB Guaranteed by design 4
COMP Sink Current 0.3 2.5 mA FB = 2.2V, COMP = 1V 4
COMP Source Current -0.5 -0.15 mA FB = 1.3V, COMP = 3V, Note 5 4
COMP Clamp Voltage 3.1 3.6 4 V VFB = 0V 4
Maximum Duty Cycle 48 49 50 % Measured at OUTA or OUTB 4
Minimum Duty Cycle 0 % COMP = 0V 4
Current Sense Gain A 1.9 2.2 2.5 V/V Note 6, guaranteed by design 4
Maximum Input Signal 0.45 0.5 0.55 V Note 7 4
CS to Output Delay 70 200 ns COMP = 3V, CS from 0 to 600mV 4
CS Sink Current 5 10 mA CS = 0.5V, RC = 5.5V, Note 8 4
Over Current Threshold 0.7 0.75 0.8 V 4
COMP to CS Offset 0.35 0.8 1.2 V CS = 0V 4
OUT Low Level 0.5 1 V I = 100mA 4
OUT High Level 0.5 1 V I = -50mA, VDD - OUT 4
Rise Time 25 60 ns CL = 1nF 4
Fall Time 25 60 ns CL = 1nF 4
CS Source Current -200 nA 4
Start Threshold 11.5 12.5 13.5 V MIC3808, Note 9 5
Minimum Operating Voltage After Start 7.6 8.3 9 V MIC3808 5
Hysteresis 3.5 4.2 5.1 V MIC3808 5
COMP Rise Time 2.5 20 ms FB = 1.8V, Rise from 0.5V to 3V 5
Startup Current 130 260 µA VDD < Start Threshold 5
Operating Supply Current 1 2 mA FB = 0V, CS = 0V, Notes 9 and 10 5
VDD Zener Shunt Voltage 13 14 15 V IDD = 10mA, Note 12 5
Supply Voltage VDD 15 V IDD ≤ 10mA 4
Supply Current IDD 20 mA 4
OUTA/OUTB Source Current (peak) -0.5 A 4
OUTA/OUTB Sink Current (peak) 1 A 4
Analog Inputs (FB, CS) -0.3 6 V -0.3V to VDD+0.3V, not to exceed 6V 4
Junction Temperature TJ -55 150 °C 4
Storage Temperature -65 150 °C 4
Lead Temperature 300 °C soldering, 10 sec. 4
ESD Rating 2 kV Note 3, human body model 4
Ambient Temperature TA -40 85 °C 4
Package Thermal Resistance SOIC-8 θJA 160 °C/W SOIC-8 4

CAD (KiCad official)

  • Symbol: MIC3808YM
  • Footprint: Package_SO:SOIC-8_3.9x4.9mm_P1.27mm
  • 3D model: SOIC-8 (KiCad packages3D, STEP)
  • 3D model files: mic3808ym-etched.step / mic3808ym-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); mic3808ym.step / mic3808ym.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Microchip Tech datasheet, copy hosted by LCSC (11 pp, sha256 ad87ed2be91323dd, retrieved 2026-11-20)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF