Generated by kicad-footprint-generator · KiCad file format 20260206
MIC3202YME
Microchip Tech · LED Drivers · SOIC-8-EP
MIC3202YME from Microchip Tech, in a SOIC-8-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VCC | power_out | Linear regulator output (4.5 V to 5.5 V at 10 mA) that powers the internal circuitry from VIN and should be bypassed with a 1 µF ceramic capacitor placed as close as possible to the VCC and AGND pins. |
| 2 | CS | input | High-side current-sense input that sets the LED current through an external sense resistor, with the sense threshold referenced to VIN (VCS(MAX) 199 to 225 mV, VCS(MIN) 165 to 189 mV). |
| 3 | VIN | power_in | Input supply for the internal circuitry (6 V to 37 V operating range, 42 V absolute maximum to PGND) and positive input of the current-sense comparator, bypassed with a 1 µF ceramic capacitor close to VIN and PGND. |
| 4 | AGND | power_in | Ground for analog circuitry and internal signal ground for all low-power sections, which should be kept separate from the PGND loop and connected at only one location. |
| 5 | EN | input | Logic-level enable input where 2.0 V or higher enables the current regulator and 0.4 V or lower (logic low) turns it off, reducing supply current below 1 µA; the output is also gated by DIM. |
| 6 | DIM | input | PWM dimming input where DIM must be at least 2.0 V to enable the output and DIM low disables the output regardless of EN, with a maximum dimming frequency of 20 kHz. |
| 7 | PGND | power_in | Power ground for the internal power FET and the high-current path, which should have a loop as small as possible and be kept separate from AGND. |
| 8 | LX | output | Drain of the internal power MOSFET connected directly to the inductor, with VLX limited to −0.3 V to (VIN + 0.6 V) to PGND, and routed away from sensitive nodes due to high-frequency, high-voltage switching. |
| 9 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | SOIC-8-EP |
| Category | Nixie Tube Driver/LED Driver |
| Pins | 9 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input Voltage Range (VIN) | VIN | 6 | 37 | V | 3 | ||
| Supply Current | IS | 1.2 | 1.75 | mA | LX Pin = open | 3 | |
| Shut Down Current | ISD | 0.05 | 5 | µA | VEN = 0V; TJ = from -40ºC to 85ºC | 3 | |
| VIN UVLO Threshold | UVLO | 3.2 | 4 | 4.5 | V | VIN Rinsing | 3 |
| VIN UVLO Hysteresis | UVLOHYS | 500 | mV | 3 | |||
| VCC Output Voltage | VCC | 4.5 | 5 | 5.5 | V | VCS = VIN = 12V, ICC = 10mA | 3 |
| Current-Sense Upper Threshold | VCS(MAX) | 199 | 212 | 225 | mV | VCS(MAX) = VIN − VCS | 3 |
| Current-Sense Lower Threshold | VCS(MIN) | 165 | 177 | 189 | mV | VCS(MIN) = VIN − VCS | 3 |
| VCS Hysteresis | VCSHYS | 35 | mV | 3 | |||
| Current-Sense Response Time (rising) | 60 | ns | VCS Rising | 3 | |||
| Current-Sense Response Time (falling) | 40 | ns | VCS Falling | 3 | |||
| Current-Sense Input Current | 3 | µA | VIN - VCS = 200mV | 3 | |||
| Maximum Switching Frequency | FMAX | 1 | MHz | 3 | |||
| VCS Hysteresis Dithering Range | VDITH | -6 | 6 | mV | Guaranteed by design | 3 | |
| Frequency Dithering Range | FDITHER | -12 | 12 | % | % of Switching Frequency | 3 | |
| EN Logic Level High | ENHI | 2 | V | 3 | |||
| EN Logic Level Low | ENLO | 0.4 | V | 3 | |||
| EN Bias Current (high) | 30 | 60 | µA | VEN = 12V | 3 | ||
| EN Bias Current (low) | 0.1 | 1 | µA | VEN = 0V | 3 | ||
| Start-up Time | 30 | µs | From EN Pin going high to LX going low | 3 | |||
| DIM Logic Level High | DIMHI | 2 | V | 4 | |||
| DIM Logic Level Low | DIMLO | 0.4 | V | 4 | |||
| DIM Bias Current (high) | 20 | 35 | µA | VDIM = 12V | 4 | ||
| DIM Bias Current (low) | 0.1 | 1 | µA | VDIM = 0V | 4 | ||
| Maximum Dimming Frequency | fDIM | 20 | kHz | 4 | |||
| MOSFET RDS(ON) | RDS(ON) | 275 | 625 | mΩ | ILX = 200mA | 4 | |
| LX Leakage Current | RDS(ON) | 5 | 50 | µA | VEN = 0V; VIN = VLX = 37V | 4 | |
| Over-Temperature Shutdown | TLIM | 160 | °C | TJ Rising | 4 | ||
| Over-Temperature Shutdown Hysteresis | TLIMHYS | 20 | °C | 4 | |||
| VIN to PGND | -0.3 | 42 | V | 3 | |||
| VLX to PGND | -0.3 | V | Max printed as (VIN + 0.6V) | 3 | |||
| VCS to PGND | -0.3 | V | Max printed as (VIN + 0.3V) | 3 | |||
| VEN to AGND | -0.3 | V | Max printed as (VIN + 0.3V) | 3 | |||
| VDIM to AGND | -0.3 | V | Max printed as (VIN + 0.3V) | 3 | |||
| VCC to PGND | -0.3 | 6 | V | 3 | |||
| PGND to AGND | -0.3 | 0.3 | V | 3 | |||
| Junction Temperature | 150 | °C | 3 | ||||
| Storage Temperature Range | -60 | 150 | °C | 3 | |||
| Lead Temperature | 260 | °C | Soldering, 10sec | 3 | |||
| Supply Voltage (VIN) | VIN | 6 | 37 | V | 3 | ||
| Enable Voltage (VEN) | VEN | 0 | V | Max printed as VIN | 3 | ||
| Dimming Voltage (VDIM) | VDIM | 0 | V | Max printed as VIN | 3 | ||
| Junction Temperature (TJ) | TJ | -40 | 125 | °C | 3 |
CAD (KiCad official)
- Symbol:
MIC3202YME - Footprint:
Package_SO:SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.29x3mm - 3D model: SOIC-8-EP (KiCad packages3D, STEP)
- 3D model files:
mic3202yme-etched.step/mic3202yme-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mic3202yme.step/mic3202yme.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (19 pp, sha256
e2d6b66242a5569e, retrieved 2026-10-30, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).