component
MIC29301-5.0WU-TR
Public Made by Adomby adom
Microchip Tech Pre-ordered MCUs, TO-263-5. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
main
MIC29301-5.0WU-TR
Microchip Tech · Pre-ordered MCUs · TO-263-5
MIC29301-5.0WU-TR from Microchip Tech, in a TO-263-5. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | EN | input | CMOS compatible control input: logic-high enables the regulator and logic-low shuts it down, and the EN input may be directly tied to 30V or below. |
| 2 | IN | power_in | Supplies the current to the output power device. |
| 3 | GND | power_in | Ground pin; the TAB is also connected internally to the IC's ground. |
| 4 | OUT | power_out | The regulator output voltage. |
| 5 | FLG | output | Active-low open-collector error flag output that pulls low to indicate an output fault condition and may sink 10 mA. |
| 6 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | TO-263-5 |
| Category | Single Chip Microcomputer/Microcontroller |
| Pins | 6 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Output Voltage | VOUT | -1 | 1 | % | IOUT = 10 mA | 5 | |
| Output Voltage | VOUT | -2 | 2 | % | 10 mA <= IOUT <= IFL, (VOUT + 1V) <= VIN <=26V (Note 3) | 5 | |
| Line Regulation | 0.06 | 0.5 | % | IOUT = 10 mA, (VOUT + 1V) <= VIN <= 26V | 5 | ||
| Load Regulation | 0.2 | 1 | % | VIN = VOUT + 1V, 10 mA <= IOUT <= 1.5A (Note 3, Note 4) | 5 | ||
| Output Voltage Temperature Coefficient | dVO/dT | 20 | 100 | ppm/°C | Output Voltage (Note 4) | 5 | |
| Dropout Voltage | 80 | 175 | mV | dVOUT = -1% (Note 5); MIC2930x IOUT = 100 mA | 5 | ||
| Dropout Voltage | 370 | 600 | mV | dVOUT = -1% (Note 5); MIC2930x IOUT = 3A | 5 | ||
| Ground Current | IGND | 10 | 35 | mA | MIC2930x IOUT = 1.5A, VIN = VOUT + 1V | 5 | |
| Current Limit | ILIM | 4.5 | 5 | A | MIC2930x, VOUT = 0V, (Note 7) | 5 | |
| Flag Output Leakage Current | 0.01 | 1 | µA | VOH = 26V | 6 | ||
| Flag Output Low Voltage | VOL | 220 | 300 | mV | Device set for 5V, VIN = 4.5V, IOL = 250 µA | 6 | |
| Flag Upper Threshold Voltage | 40 | 60 | mV | Device set for 5V (Note 10) | 6 | ||
| Flag Lower Threshold Voltage | 75 | 95 | mV | Device set for 5V (Note 10) | 6 | ||
| Flag Hysteresis | 15 | mV | Device set for 5V (Note 10) | 6 | |||
| Enable Input Logic Voltage Low (OFF) | 0.8 | V | 7 | ||||
| Enable Input Logic Voltage High (ON) | 2.4 | V | 7 | ||||
| Enable Pin Input Current | 100 | 600 | µA | VEN = 26V | 7 | ||
| Enable Pin Input Current | 0.7 | 2 | µA | VEN = 0.8V | 7 | ||
| Regulator Output Current in Shutdown | 10 | 500 | µA | VEN <= 0.8V and VIN <= 26V, VOUT = 0 | 7 | ||
| Input Supply Voltage | VIN | -20 | 60 | V | Note 1: limited duration (<100 ms), duty cycle <=1% | 4 | |
| Enable Input Voltage | VEN | -0.3 | V | Maximum is VIN | 4 | ||
| Maximum Operating Input Voltage | 26 | V | 4 | ||||
| Storage Temperature Range | TS | -65 | 150 | °C | 8 | ||
| Operating Junction Temperature | TJ | -40 | 125 | °C | 8 | ||
| Lead Temperature | 260 | °C | Soldering, 5 sec. | 8 | |||
| Thermal Resistance TO-263 Junction-to-Case | θJC | 2 | °C/W | 8 | |||
| Dropout Voltage | 250 | mV | MIC2930x IOUT = 1.5A | 5 | |||
| Ground Current | IGND | 37 | mA | MIC2930x IOUT = 3A | 5 | ||
| Ground Pin Current at Dropout | IGRNDDO | 1.7 | mA | MIC2930x, VIN = 0.5V less than specified VOUT × IOUT = 10 mA | 5 | ||
| Output Noise Voltage (10 Hz to 100 kHz) | en | 400 | µVRMS | IL = 100 mA, CL = 10 µF | 6 | ||
| Output Noise Voltage (10 Hz to 100 kHz) | en | 260 | µVRMS | IL = 100 mA, CL = 33 µF | 6 |
CAD (KiCad official)
- Symbol:
MIC29301-5.0WU-TR - Footprint:
Package_TO_SOT_SMD:TO-263-5_TabPin6 - 3D model: TO-263-5 (KiCad packages3D, STEP)
- 3D model files:
mic29301-5-0wu-tr-etched.step/mic29301-5-0wu-tr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mic29301-5-0wu-tr.step/mic29301-5-0wu-tr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (42 pp, sha256
e4243475719303fc, retrieved 2026-10-27, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# MIC29301-5.0WU-TR
**Microchip Tech** · Pre-ordered MCUs · TO-263-5
MIC29301-5.0WU-TR from Microchip Tech, in a TO-263-5. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | EN | input | CMOS compatible control input: logic-high enables the regulator and logic-low shuts it down, and the EN input may be directly tied to 30V or below. |
| 2 | IN | power_in | Supplies the current to the output power device. |
| 3 | GND | power_in | Ground pin; the TAB is also connected internally to the IC's ground. |
| 4 | OUT | power_out | The regulator output voltage. |
| 5 | FLG | output | Active-low open-collector error flag output that pulls low to indicate an output fault condition and may sink 10 mA. |
| 6 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | TO-263-5 |
| Category | Single Chip Microcomputer/Microcontroller |
| Pins | 6 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Output Voltage | VOUT | -1 | | 1 | % | IOUT = 10 mA | 5 |
| Output Voltage | VOUT | -2 | | 2 | % | 10 mA <= IOUT <= IFL, (VOUT + 1V) <= VIN <=26V (Note 3) | 5 |
| Line Regulation | | | 0.06 | 0.5 | % | IOUT = 10 mA, (VOUT + 1V) <= VIN <= 26V | 5 |
| Load Regulation | | | 0.2 | 1 | % | VIN = VOUT + 1V, 10 mA <= IOUT <= 1.5A (Note 3, Note 4) | 5 |
| Output Voltage Temperature Coefficient | dVO/dT | | 20 | 100 | ppm/°C | Output Voltage (Note 4) | 5 |
| Dropout Voltage | | | 80 | 175 | mV | dVOUT = -1% (Note 5); MIC2930x IOUT = 100 mA | 5 |
| Dropout Voltage | | | 370 | 600 | mV | dVOUT = -1% (Note 5); MIC2930x IOUT = 3A | 5 |
| Ground Current | IGND | | 10 | 35 | mA | MIC2930x IOUT = 1.5A, VIN = VOUT + 1V | 5 |
| Current Limit | ILIM | | 4.5 | 5 | A | MIC2930x, VOUT = 0V, (Note 7) | 5 |
| Flag Output Leakage Current | | | 0.01 | 1 | µA | VOH = 26V | 6 |
| Flag Output Low Voltage | VOL | | 220 | 300 | mV | Device set for 5V, VIN = 4.5V, IOL = 250 µA | 6 |
| Flag Upper Threshold Voltage | | 40 | 60 | | mV | Device set for 5V (Note 10) | 6 |
| Flag Lower Threshold Voltage | | | 75 | 95 | mV | Device set for 5V (Note 10) | 6 |
| Flag Hysteresis | | | 15 | | mV | Device set for 5V (Note 10) | 6 |
| Enable Input Logic Voltage Low (OFF) | | | | 0.8 | V | | 7 |
| Enable Input Logic Voltage High (ON) | | 2.4 | | | V | | 7 |
| Enable Pin Input Current | | | 100 | 600 | µA | VEN = 26V | 7 |
| Enable Pin Input Current | | 0.7 | | 2 | µA | VEN = 0.8V | 7 |
| Regulator Output Current in Shutdown | | | 10 | 500 | µA | VEN <= 0.8V and VIN <= 26V, VOUT = 0 | 7 |
| Input Supply Voltage | VIN | -20 | | 60 | V | Note 1: limited duration (<100 ms), duty cycle <=1% | 4 |
| Enable Input Voltage | VEN | -0.3 | | | V | Maximum is VIN | 4 |
| Maximum Operating Input Voltage | | | | 26 | V | | 4 |
| Storage Temperature Range | TS | -65 | | 150 | °C | | 8 |
| Operating Junction Temperature | TJ | -40 | | 125 | °C | | 8 |
| Lead Temperature | | | | 260 | °C | Soldering, 5 sec. | 8 |
| Thermal Resistance TO-263 Junction-to-Case | θJC | | 2 | | °C/W | | 8 |
| Dropout Voltage | | | 250 | | mV | MIC2930x IOUT = 1.5A | 5 |
| Ground Current | IGND | | 37 | | mA | MIC2930x IOUT = 3A | 5 |
| Ground Pin Current at Dropout | IGRNDDO | | 1.7 | | mA | MIC2930x, VIN = 0.5V less than specified VOUT × IOUT = 10 mA | 5 |
| Output Noise Voltage (10 Hz to 100 kHz) | en | | 400 | | µVRMS | IL = 100 mA, CL = 10 µF | 6 |
| Output Noise Voltage (10 Hz to 100 kHz) | en | | 260 | | µVRMS | IL = 100 mA, CL = 33 µF | 6 |
## CAD (KiCad official)
- Symbol: `MIC29301-5.0WU-TR`
- Footprint: `Package_TO_SOT_SMD:TO-263-5_TabPin6`
- 3D model: TO-263-5 (KiCad packages3D, STEP)
- 3D model files: `mic29301-5-0wu-tr-etched.step` / `mic29301-5-0wu-tr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `mic29301-5-0wu-tr.step` / `mic29301-5-0wu-tr.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Microchip Tech datasheet](docs/mic29301-5-0wu-tr-datasheet.pdf) (42 pp, sha256 `e4243475719303fc`, retrieved 2026-10-27, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/mic29301-5-0wu-tr-datasheet.pdf)