Generated by kicad-footprint-generator · KiCad file format 20260206
MIC29150-12WT
Microchip Tech · Power Management Specialized - PMIC · TO-220
MIC29150-12WT from Microchip Tech, in a TO-220. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | IN | power_in | Supplies the current to the output power device. Line transient protection allows survival of input spikes between -20V and +60V, and the overvoltage sensor disables the regulator above approximately 32V. |
| 2 | GND | power_in | Ground connection. The TAB is also connected internally to the IC's ground. |
| 3 | OUT | power_out | The regulator output voltage. A minimum output capacitor of 10 µF at full load is required for the MIC2915x (Table 4-1). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | TO-220 |
| Category | Power Supply Chip |
| Pins | 3 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Output Voltage | VOUT | -1 | 1 | % | IOUT = 10 mA | 5 | |
| Output Voltage over load and line | VOUT | -2 | 2 | % | 10 mA ≤ IOUT ≤ IFL, (VOUT + 1V) ≤ VIN ≤26V (Note 3) | 5 | |
| Line Regulation | 0.06 | 0.5 | % | IOUT = 10 mA, (VOUT + 1V) ≤ VIN ≤ 26V | 5 | ||
| Load Regulation | 0.2 | 1 | % | VIN = VOUT + 1V, 10 mA ≤ IOUT ≤ 1.5A (Note 3, Note 4) | 5 | ||
| Output Voltage Temperature Coefficient | ΔVO/ΔT | 20 | 100 | ppm/°C | Output Voltage (Note 4) | 5 | |
| Dropout Voltage MIC2915x | 80 | 200 | mV | ΔVOUT = -1% (Note 5); MIC2915x IOUT = 100 mA | 5 | ||
| Dropout Voltage MIC2915x | 350 | 600 | mV | MIC2915x IOUT = 1.5A | 5 | ||
| Ground Current MIC2915x | IGND | 8 | 20 | mA | MIC2915x IOUT = 750 mA, VIN = VOUT + 1V | 5 | |
| Current Limit MIC2915x | ILIM | 2.1 | 3.5 | A | MIC2915x, VOUT = 0V, (Note 7) | 5 | |
| Ground Current in Shutdown | 2 | 10 | µA | MIC29150/1/2/3 only | 6 | ||
| Ground Current in Shutdown | 30 | µA | VEN = 0.4V | 6 | |||
| Regulator Output Current in Shutdown | 10 | 500 | µA | VEN ≤ 0.8V and VIN ≤ 26V, VOUT = 0 | 7 | ||
| Input Logic Voltage Low (OFF) | 0.8 | V | 7 | ||||
| Input Logic Voltage High (ON) | 2.4 | V | 7 | ||||
| Enable Pin Input Current | 100 | 600 | µA | VEN = 26V | 7 | ||
| Enable Pin Input Current | 750 | µA | VEN = 26V | 7 | |||
| Enable Pin Input Current | 0.7 | 2 | µA | VEN = 0.8V | 7 | ||
| Enable Pin Input Current | 4 | µA | VEN = 0.8V | 7 | |||
| Output Leakage Current (Flag) | 0.01 | 1 | µA | VOH = 26V | 6 | ||
| Output Leakage Current (Flag) | 2 | µA | VOH = 26V | 6 | |||
| Output Low Voltage | VOL | 220 | 300 | mV | Device set for 5V, VIN = 4.5V | 6 | |
| Output Low Voltage | VOL | 400 | mV | Device set for 5V, VIN = 4.5V, IOL = 250 µA | 6 | ||
| Upper Threshold Voltage | 40 | 60 | mV | Device set for 5V, (Note 10) | 6 | ||
| Upper Threshold Voltage | 25 | mV | Device set for 5V, (Note 10) | 6 | |||
| Lower Threshold Voltage | 75 | 95 | mV | Device set for 5V, (Note 10) | 6 | ||
| Lower Threshold Voltage | 140 | mV | Device set for 5V, (Note 10) | 6 | |||
| Hysteresis | 15 | mV | Device set for 5V, (Note 10) | 6 | |||
| Minimum Load Current | 5 | mA | MIC2915x (Table 4-2) | 25 | |||
| Input Supply Voltage | VIN | -20 | 60 | V | Note 1: 60V limited to <100 ms and duty cycle ≤1% | 4 | |
| Maximum Operating Input Voltage | 26 | V | 4 | ||||
| Storage Temperature Range | TS | -65 | 150 | °C | 8 | ||
| Operating Junction Temperature | TJ | -40 | 125 | °C | 8 | ||
| Lead Temperature | 260 | °C | Soldering, 5 sec. | 8 | |||
| Dropout Voltage MIC2915x | 220 | mV | MIC2915x IOUT = 750 mA | 5 | |||
| Ground Current MIC2915x | IGND | 22 | mA | MIC2915x IOUT = 1.5A | 5 | ||
| Ground Pin Current at Dropout | IGRNDDO | 0.9 | mA | MIC2915x, VIN = 0.5V less than specified VOUT; IOUT = 10 mA | 5 | ||
| Output Noise Voltage (10 Hz to 100 kHz) | en | 400 | µVRMS | IL = 100 mA, CL = 10 µF | 6 | ||
| Output Noise Voltage (10 Hz to 100 kHz) | en | 260 | µVRMS | IL = 100 mA, CL = 33 µF | 6 | ||
| Thermal Resistance TO-220 | θJC | 2 | °C/W | 8 |
CAD (KiCad official)
- Symbol:
MIC29150-12WT - Footprint:
Package_TO_SOT_THT:TO-220-3_Vertical - 3D model: TO-220 (KiCad packages3D, STEP)
- 3D model files:
mic29150-12wt-etched.step/mic29150-12wt-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mic29150-12wt.step/mic29150-12wt.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (42 pp, sha256
e4243475719303fc, retrieved 2026-10-28, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).